Engine firing order and balance calculator
Pick an engine layout, or type your own crank angles and bank angles, and see every firing order the crankshaft allows, with a cycle chart of what each cylinder is doing. It also gives the engine's primary and secondary shaking forces and rocking couples, says which a crank counterweight can cancel and which need balance shafts, and covers inline, V and flat engines. Free, no sign-up, runs in your browser.
It opens on the worked example from Skill-Lync's four-cylinder engine guide: a Honda City 1.5 (73.0 × 89.5 mm) at its 6,600 rpm power peak, with an illustrative 0.5 kg reciprocating mass and r/l = 0.30.
16 layouts · four- and two-stroke · exact slider-crank peak · checked against an independent script (960 checks at build) · Updated 22 Nov 2026
Crank lag ψ: how many degrees this cylinder's crank pin trails throw 1, in the direction of rotation. Bank β: the cylinder's axis from vertical, seen from the front, clockwise positive (0 for an inline engine, ±45° for a 90° V). Throw: which crank throw it sits on, front = 1; throws are a pitch a apart.
- Even firing: a power stroke every 180° of crank angle. This crank allows 2 firing orders that start at cylinder 1.
- No primary force: it cancels exactly.
- The secondary force (12,826 N peak) shakes the engine up and down at twice crank speed. Cancelling it takes a pair of counter-rotating balance shafts at twice crank speed.
- No primary couple: it cancels exactly.
- No secondary couple: it cancels exactly.
- Couples are taken about the middle of the crankshaft; with an unbalanced force they change with the reference point.
Left: the crank throws (numbers) and cylinder bores seen from the front, throw 1 straight up. Middle and right: the path traced over one revolution by the primary (blue, 1st order) and secondary (orange, 2nd order) shaking force and rocking couple. A circle rotates at constant size; a straight line acts along one direction.
How to use the firing order calculator
- Pick a layout from the list or the buttons. That fills the cylinder table with its crank lags, bank angles and throws. To try your own crankshaft, edit the table; the layout switches to Custom.
- Set the size and speed: the reciprocating mass per cylinder (the piston, pin, rings and about a third of the connecting rod), the stroke, r/l and the rpm. The pitch a is the distance between throws, used for the couples.
- Read the firing orders. Every order the crank allows is listed; click one to see its cycle chart. If no order fires evenly, the calculator shows the most even ones and their gaps.
- Read the balance. Each force and couple is given as its peak over a revolution and as a type: cancels, rotates with the crank (a crank counterweight can remove it), rotates against it, or acts along one line (half of a primary one yields to counterweights; a secondary one needs a pair of balance shafts).
How is the firing order of an engine worked out?
Start from the crank angle at which each piston reaches top dead centre. With θ the angle of throw 1, cylinder i's crank is αi past its own TDC, where ψi is its crank lag and βi its bank angle:
A four-stroke cylinder reaches TDC twice in its 720° cycle, once ending compression and once ending exhaust, and it fires on one of them. So every cylinder after the first has two possible firing angles:
The calculator tries all 2N−1 combinations and keeps those whose firings are equally spaced. On an inline-four's flat crank, pistons 1 and 4 reach TDC together, and so do 2 and 3. Cylinder 4 must fire 360° after cylinder 1, and of cylinders 2 and 3 one fires at 180° and the other at 540°. That leaves exactly two orders, 1-3-4-2 and 1-2-4-3. A two-stroke fires on every TDC, so its crank fixes a single order.
Numbering decides how a firing order reads. This page numbers inline engines front to back. V engines go along the left bank first, then the right; flat engines go along the crank, with the banks alternating. Manufacturers differ: GM numbers V8s alternately bank to bank, while Ford numbers one bank and then the other. A published firing order only matches this page's numbering after you renumber the cylinders.
Firing orders and balance of common engine layouts
All computed by the calculator for equal throw pitch a. Forces are in multiples of m r ω² (primary) and m r ω²/n (secondary); couples in multiples of m r ω² a and m r ω² a/n. "rot." means the part left rotates with the crank at constant size, so crank counterweights can cancel it. "0" means it cancels exactly.
| Layout | Firing interval | Firing orders (this page's numbering) | Primary force | Secondary force | Primary couple | Secondary couple |
|---|---|---|---|---|---|---|
| Single | 720° even | 1 | 1.000 | 1.000 | - | - |
| Parallel twin, 360° | 360° even | 1-2 | 2.000 | 2.000 | 0 | 0 |
| Parallel twin, 180° | 180/540° uneven | 1-2 | 0 | 2.000 | 1.000 | 0 |
| Parallel twin, 270° | 270/450° uneven | 1-2 | 1.414 | 0 | 0.707 | 1.000 |
| Inline-3 | 240° even | 1-2-3 | 0 | 0 | 1.732 | 1.732 |
| Inline-4 | 180° even | 1-3-4-2, 1-2-4-3 | 0 | 4.000 | 0 | 0 |
| Inline-5 | 144° even | 1-2-4-5-3 | 0 | 0 | 0.449 | 4.980 |
| Inline-6 | 120° even | 1-5-3-6-2-4, 1-5-4-6-2-3, 1-2-4-6-5-3 (+1 more) | 0 | 0 | 0 | 0 |
| V-twin, 90° | 450/270° uneven | 1-2 | 1.000 rot. | 1.414 | - | - |
| Flat twin (boxer) | 360° even | 1-2 | 0 | 0 | 1.000 | 1.000 |
| Flat-4 (boxer) | 180° even | 1-4-2-3, 1-3-2-4 | 0 | 0 | 0 | 2.000 |
| Flat-6 (boxer) | 120° even | 1-6-4-2-5-3, 1-6-3-2-5-4, 1-5-4-2-6-3 (+1 more) | 0 | 0 | 0 | 0 |
| V6, 90°, shared pins | 90/120/150° uneven | 1-4-6-5-3-2, 1-3-6-5-4-2, 1-4-2-5-3-6 (+1 more) | 0 | 0 | 1.732 rot. | 2.449 |
| V8, 90°, cross-plane | 90° even | 1-5-6-8-7-2-4-3, 1-2-6-8-7-5-4-3, 1-5-4-8-7-2-6-3 (+5 more) | 0 | 0 | 3.162 rot. | 0 |
| V8, 90°, flat-plane | 90° even | 1-8-3-7-4-5-2-6, 1-8-2-7-4-5-3-6, 1-8-3-6-4-5-2-7 (+5 more) | 0 | 5.657 | 0 | 0 |
| V12, 60° | 60° even | 1-12-5-11-4-10-6-7-2-8-3-9, 1-12-5-11-3-10-6-7-2-8-4-9, 1-12-2-11-4-10-6-7-5-8-3-9 (+29 more) | 0 | 0 | 0 | 0 |
A few patterns stand out. The inline-six, the flat-six and the V12 cancel everything at first and second order, which is why they are the classic smooth engines. Inline-3 and inline-5 cancel their forces but rock end to end. An inline-4 leaves a pure secondary force of 4 m r ω²/n, and a flat-plane V8 leaves 5.657× that unit (4√2) acting sideways. The cross-plane V8 cancels every force, and its only first-order leftover is a couple that rotates with the crank, which counterweights remove.
Primary and secondary forces and couples
Each piston's reciprocating parts, mass m, push on the block along the cylinder axis with the familiar two-term inertia force:
The cos α term repeats once per revolution (primary) and the cos 2α term twice (secondary, from the connecting rod's angle). The calculator adds them up as vectors in the end view, with êi the unit vector along cylinder i's axis, and takes the couples about the middle of the crankshaft:
Over a revolution each sum traces an ellipse. The calculator splits it into a part rotating with the crank and a part rotating against it. A part rotating with the crank at crank speed can be cancelled by counterweights on the crankshaft. A part rotating against it needs a counter-rotating balance shaft. A force along a single line is two equal parts, so at crank speed counterweights can take half and a counter-rotating shaft the rest; at twice crank speed it takes a pair of shafts. Secondary terms rotate at twice crank speed, so only balance shafts at twice crank speed touch them; crank counterweights cannot.
Rotating masses (crank pins, webs, the big end of the rod) are assumed balanced by the crankshaft's own counterweights; the calculator deals only with the reciprocating mass. When a net force is left over, the couple depends on the point you take it about. This page uses the middle of the throws.
Worked example: a 1.5-litre inline-4 at 6,600 rpm
Honda publishes the City 1.5 i-VTEC's bore and stroke as 73.0 × 89.5 mm and its peak power at 6,600 rpm. The rod length and reciprocating mass are not published, so r/l = 0.30 and m = 0.5 kg are illustrative. Then r = 44.75 mm, ω = 691.2 rad/s and m r ω² = 10,688 N per cylinder.
- Primary: pistons 1 and 4 are 180° from 2 and 3, so the four primary forces cancel. The two ends mirror each other, so the couples cancel too.
- Secondary: at twice the crank angle, 180° becomes 360° and all four add: 4 × 10,688 × 0.30 = 12,826 N, straight up and down at 2 × 6,600/60 = 220 Hz.
- Exact peak: with the full slider-crank motion the peak is 13,445 N, 4.8% higher, from the harmonics the two-term formula drops. At 3,000 rpm the same engine shakes with 2,650 N, because the force grows with speed squared.
These are the guide's published numbers (10,688 N, 12,826 N, 13,445 N), and the build stops if the calculator drifts from them. The exact force uses the slider-crank acceleration with λ = r/l:
Why does an inline-3 rock end to end?
Its throws are 120° apart, so the three primary forces add to zero, and at twice the angle (240°) so do the secondaries. The couples don't cancel. Take them about the middle cylinder: cylinder 1 is a pitch a in front at TDC angle 0°, cylinder 3 a pitch behind at 120°, and the middle cylinder has no lever arm. That gives (Skill-Lync's derivation, which the calculator and its check script confirm):
The secondary couple works the same way at 2θ and is √3 m r ω² a/n. For the example sizes (pitch 84 mm) that is 1,555 N·m primary and 467 N·m secondary at 6,600 rpm. The primary part can be halved with crank counterweights but not removed; some three-cylinder engines add a balance shaft for it. The inline-5 behaves similarly: its 1-2-4-5-3 order leaves a small primary couple (403 N·m) and a larger secondary one (1,341 N·m).
V-twins, V8s and flat engines
90° V-twin, one shared crank pin. With the cylinders at ±45° their primary forces are at right angles, and they add to a vector of constant size that turns with the crank:
So |Fp| = m r ω² (10,688 N here) at every angle, and a counterweight equal to one cylinder's reciprocating mass, at crank radius opposite the pin, cancels it completely. That is why the 90° V-twin is said to have perfect primary balance. The secondary force does not cancel: it is √2 m r ω²/n (4,535 N), acting horizontally. The twin fires 270° then 450° apart.
Cross-plane V8 (throws 0°, 90°, 270°, 180°): every primary and secondary force cancels, and so does the secondary couple. The primary couple is √10 m r ω² a (2,839 N·m here), but it rotates with the crank at constant size, so the crankshaft's counterweights balance it. The flat-plane V8 is two inline-4s at 90°: their vertical secondaries cancel and the horizontal ones add to 18,139 N.
90° V6 on shared pins (an inline-3 crank under 90° banks): its primary couple turns into a rotating one (1,555 N·m) that counterweights can cancel, but its secondary couple (660 N·m) stays, and it cannot fire evenly. Early 90° V6s built this way ran at alternating 90°/150° intervals. Later ones used split crank pins offset by 30° to fire every 120°. Flat engines: opposed pistons cancel each other's forces, but the two are offset along the crank, so a small couple is left. On the flat-4 the primary couples of its two pairs cancel and a secondary couple (539 N·m) remains. The flat-6's three pairs cancel completely in this model.
What this calculator does not cover
- Torque fluctuation and torsional vibration from gas pressure: the firing order changes these, and the flywheel and crank damper handle them. Balance here is about inertia forces only.
- Rotating-mass imbalance (crank pins, webs, big ends): assumed counterweighted.
- Fourth and higher orders. The table and tiles use the two-term formula. Only the exact peak includes all harmonics, which is why a "balanced" six or V12 still shows a few newtons there.
- Side-by-side connecting rods and bank offsets in V and flat engines (each cylinder's small axial offset), and staggered or unequal throw spacing; enter separate throws to approximate them.
- Engine mounts, balance-shaft sizing and phasing, and bearing loads.
Engine and NVH teams work out firing orders, balance and the forces on the block before a prototype runs, then model the whole engine in 1D tools like GT-POWER. Skill-Lync's IC engine courses teach that workflow.
Frequently asked questions
What is the firing order of a 4-cylinder engine?
Almost every inline-four fires 1-3-4-2; some engines, historically several British ones, use 1-2-4-3. Both give a power stroke every 180°. The flat-plane crank (throws 0°, 180°, 180°, 0°) puts pistons 1 and 4 at TDC together, and so 2 and 3, which leaves exactly these two orders. The calculator finds both.
What is the firing order of a 6-cylinder engine?
The usual inline-six order is 1-5-3-6-2-4, one power stroke every 120°. Its crank pairs throws 1-6, 2-5 and 3-4, and each pair can fire either way round, so the same crank allows 4 orders. All of them leave the inline-six with no unbalanced primary or secondary force or couple.
How do you find the firing order from the crank angles?
Work out the crank angle at which each piston reaches top dead centre. In a four-stroke engine each cylinder reaches TDC twice per cycle and fires on one of them. Try both choices for every cylinder and keep the combinations whose firings are equally spaced, 720° divided by the number of cylinders.
What is primary and secondary balance in an engine?
A piston's inertia force has a part at crank speed, m r ω² cos θ (primary), and a smaller part at twice crank speed, m r ω² cos 2θ/n (secondary), from the connecting rod's angle. An engine is primary or secondary balanced when those parts cancel across its cylinders, as forces and as end-to-end rocking couples.
Why does an inline-4 need balance shafts?
Its secondary forces don't cancel: all four add, so the block shakes up and down at twice crank speed with 4 m r ω²/n. For the 1.5-litre example at 6,600 rpm that is 12,826 N. Bigger inline-fours use two shafts turning in opposite directions at twice crank speed (Lanchester shafts) to cancel it.
Is an inline-3 engine balanced?
Its forces are: the primary and secondary forces of the three cylinders cancel. Its couples are not, because the outer cylinders are a pitch either side of the middle one. The primary couple is √3 m r ω² a, 1,555 N·m for this page's example, and rocks the engine end to end.
Related on Skill-Lync
- Four-cylinder engine: how it works, firing order 1-3-4-2 and balance (the guide this example comes from)
- Theory of Machines interactive book (balancing of reciprocating masses)
- IC engine performance test calculator
- Otto, Diesel and dual cycle calculator
- Cam profile calculator
- How do IC engines work?
- IC engine and combustion courses
- All free engineering tools
Sources
- Wikipedia, Firing order: "Straight-four engines typically use a firing order of 1-3-4-2, however some British engines used a firing order of 1-2-4-3"; even firing "requires a firing interval of 720 divided by the number of cylinders"; for the inline-3 "no effective difference between the possible firing orders of 1-2-3 and 1-3-2". Read 22 Nov 2026.
- Wikipedia, Engine balance: inline-six "uses a 120° crankshaft and firing order 1-5-3-6-2-4" with perfect primary and secondary balance; the inline-four's "secondary reciprocating forces are high, due to all four pistons being in phase at twice the rotating frequency", cancelled by shafts that "rotate in opposite directions at twice engine speed, known as Lanchester shafts"; 90° V6s with Honda's 30° offset pins "resulting in an even firing interval". Read 22 Nov 2026.
- Wikipedia, Straight-five engine: "Most four-stroke straight-five engines use a firing order of 1-2-4-5-3", giving "the minimal primary (crank speed) rocking couple". V-twin engine: 90° "can achieve a perfect primary balance"; "the second cylinder firing 270 degrees after the first cylinder, then a 450 degrees interval". V6 engine: early 90° V6s had a 90°/150° firing pattern; many use "split crankpins offset by 30 degrees". Read 22 Nov 2026.
- Wikipedia, Crossplane: the end and middle throws give "a primary (crank speed) rocking couple", offset by counterweights in a 90° V8, and the banks "cancel the second-order free forces entirely". Flat-four engine: the opposed primary couples cancel, leaving "a secondary rocking couple". Flat-six engine: "perfect primary and secondary balance". Read 22 Nov 2026.
- Engine Labs, flat-plane vs cross-plane V8: on the flat-plane, "the horizontal components add together ... while the vertical components cancel out". Engine Labs, firing order swaps: GM "number their cylinders by alternating from bank to bank", Ford "sequentially down the right side and then the left". Read 22 Nov 2026.
- NPTEL, Dynamics of Machines (course 112101096), Module 5, unbalance in multi-cylinder engines: four-cylinder cranks at θ, θ+180°, θ+180°, θ: "the primary forces are completely balanced but not the secondary forces" and "the primary and secondary moments are completely balanced". Read 22 Nov 2026.
- CodeCogs, Balancing of reciprocating masses: "Inertia Force = M r ω² (cos θ + cos 2θ / n)"; "one-third of the mass of the connecting-rod may be treated as being concentrated at the cross head pin". Read 22 Nov 2026.
- Skill-Lync, Four-cylinder engine guide (refreshed 16 Nov 2026): the Honda City 1.5 example (73.0 × 89.5 mm, 6,600 rpm, Honda's figures; r/l 0.30 and 0.5 kg illustrative) and its results, 10,688 N, 12,826 N and 13,445 N exact, which this page reproduces.
- Skill-Lync, scripts/verify/engine_balance.py: recomputes every case without the two-term formula. Forces come from the exact slider-crank geometry, with finite-difference accelerations, Fourier fits and singular values, and couples as 3-D cross products. Firing orders come from a backtracking search over cylinder sequences. It covers the 16 layouts, 4 other set-ups and 40 random engines, and the page compares 960 numbers with it when it is built. The √3, √2, √10 and 4√2 factors on this page are Skill-Lync's derivations, confirmed by that script.