Wiring harness routing & packaging Rules Week 3 Challenge

AIM: Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end) Steps to be followed:…

Aim : To define given P clamp CAD data as an electrical support using electrical part design workbench & define all the necessary properties. to define given Backshell CAD data as an electrical backshell using electrical part design workbench & define all the necessary properties. To create COT tubes with outer…

Wiring harness design in CATIA V5 - 3D modeling CONNECTOR MODELING Download the specified connector from te.com. In the part design workbench provides the center point and axis system to the wire inserting end and connection end. The axis must be given in a specified way:  X-axis: Towards the clamp  Y-axis: Towards the…

Final Assembly of Yacht Objective:-    Design the individual components of a yacht and assemble them together by using solidworks. Introduction:-      A yacht is a watercraft used for pleasure or sports. The term originates from the Dutch word Yacht, and originally referenced light, fast sailing…

  Assembly of American chopper: Objective: To design individual parts  of an American chopper with fully defined sketches and appropriate appearances. To assemble all the individual parts of the American chopper to create the chopper model. To render the chopper model by adding appearances, decals, lights, cameras,…

BACK DOOR DESIGN AIM: To develop back door design by given class A surface following automotive design rule by using NX CAD. INTRODUCTION: Back Door is a Automotive component of a car to cover the rear side of the vehicle and it is also called Tailgate.It is the most important component during the rear crash and it should…

ROOF DESIGN: INTRODUCTION: An automobile roof is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Though it just looks like a styling surface that protects from sun, wind and other elements, various environmental…

FENDER DESIGN INTRODUCTION: ABOUT FENDER:                                                                      A fender is the…

Objective:                   To increase the section modulus of the hood by necessary changes. SOFTWARE USED: NX CAD Section modulus:             Section modulus is a geometric property for a given cross-section used in the design of beams…

Automotive Hood Design Introduction:                      The term car hood is a North American term, used primarily in America and Canada. Hood comes from the Old English word hod which means a hood, a soft covering for the head. Interestingly, hood is used by…

UNDERBODY COATING                    ABOUT UNDERBOADY COATING: Automotive underbody coatings are applied on the underside of vehicles to provide a protective layer of protection between vehicle’s underside and damaging forces such as moisture, corrosion, stone chip damage and weather resistance. Automotive underbody coatings…

BENCHMARK REQUIREMENT:         Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, five-year-old boy, his father, and his mother. He visits his native place Madurai which is 500kms away from Bangalore…

DESIGN OF VEHICLE DOOR TRIM PLANE  AIM:         To create a solid body of side door including engineering features by using given class A surface and master section. SOFTWARE USED: CATIA V5 INDRODUCTION:     By using class A and mastersection we going to create calss B,class c.In this…

AIM:  To create the part model and assembly for the given drawing.DRAWING - 1CV JOINT First create sketches for the given diagram in part workbench and then assemble it.Sketches and CAD part are given belowAfter creating all parts go to assembly workbench START -> MECHANICAL DESIGN -> ASSEMBLY DESIGN.Insert…

AIM :         To design a B pillar with the given mastersection. MASTER SECTION:   Mastersection helps you to do decide the fesibility the clearance,packaging,and the fixation stratege of component before bucking it into the component.mastersection are the guide for design recuriments which decide…

AIM :         To create a door applique design from the given class A surface and create engineering features. PLATFORM USED : CATIA V5 INTRODUCTION : HEAT STAKING :         Heat staking is a pulsed heat process to join two or more part out of whish one at least is made of plastic…

                                                                                           …

                                                                                           …

AIM :        To create core and cavity design for SWITCH PANEL BEZEL. SOFTWARE USED :   CATIA v5 PROCEDURE : Take boundary by using class A surface  and then extrapolate .  Join extrapolate surface with class c and trim it off.with the trim surface join class B surface and create parting surface. After creating parting…

AIM:        Create coin holder design through class A surface. PROCEDURE : First create tooling direction by using class A surface. Keep class A as a reference to create class B and class C surface. Join class A and c together and class B surface and trim it. Finally analysis tooling direction by draft…

DOOR ARM REST : AIM :         Create class B and Class c surface by using given class A surface at thickness of 2.5mm.   PROCEDURE : First create tooling direction,if required create side tooling also. By using class A surface create class B and C surface. Join A,B and C surface together and…