Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge

The Motor blower assembly consists of 5 Parts which are first created as part files and later on assembled in an assembly file using different constraints. LOWER HOUSING: The lower housing was created using different features like Extrude, shell, cut and mirror.   UPPER HOUSING: The upper housing was created using…

OBJECTIVES Create the Door trim Panel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. To Create the Heat stakes and locators in the lower…

A-PILLAR DESIGN WITH MASTER SECTION   AIM: To create the A-Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. CLASS A SURFACE:           Class…

 AIM: Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create the Heat Stakes and the locators considering the…

Attachment Feature Creation - Challenge 2 AIM Create the Dog House for the Door Trim considering the design rules INTRODUCTION DOG HOUSE The dog house is an engineering feature used in plastic design. Dog houses are used as a support feature. Sometimes other engineering features like snaps, locators, and screw bosses are…

                                                  Attachment Feature Creation (Ribs & Screw Boss) AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling…

                                                                      Bumper Design   AIM: to make a model from the provided class-A…

OBJECTIVE:-  The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help of Bisecting method. INTRODUCTION:-  The control panel bezel is the frame part of the window switch that holds its switch covers and buttons into place.…

  AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. REPORT ON DRAFT ANALYSIS: Given Class A Surface:…

HERE ALL DATA ZIP FILES ARE ATTACHED BELOW. QUICK RETURN MECHANISM  CV JOINT ALL PARTS AND ASSEMBLY ARE IN A ZIP FILE AS MENTIONED IN THE QUESTION.

Aim:- To Design Back Door using given Styling Surface. Introduction:- The backdoor or tailgate is the rearmost part of the automobile which opens upwards, downwards, and sideways to give access to the luggage space or seating. In most automobiles, the backdoor opens upwards. It is hinged to the roof and a gas stay support…

                                                                                 Roof Design   OBJECTIVE : The…

CALCULATING AND OPTIMIZING THE SECTION MODULUS OF DESIGNED CAR HOOD USING NX-CAD SOFTWARE   Objective: To calculate the section modulus using the hood cross section and to come up with new section of optimized section modulus as compare to the previous section in order to increase the stregth and stiffness of the…

                                                           Project :- FENDER DESIGN USING NX 12   Objective : The main object of this project is to design the BIW(Body…

FENDER:- Fender is the term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spary from being thrown into the air by the rotating tire. Fenders are typically rigid and can be…

                                                                     Answer of Design Of Hood inner panel     Design Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section mentioned with the Design parameters explained in  ASSEMBLY of Hood Inner Panel, Outer Panel, Latch, Hinge and…

                                                                           UNDERBODY COATING   In Indian road conditions,…

Question:- Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, a five-year-old boy, his father, and his mother. He visits his native place…

Final Project - 2: Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings to all bundle. First of All to Download all requireed data from given…

                                                               Project 1:- Engine Wiring Harness Here First of All download the data given in the question and download it and follow the process which shown in tutorial Downloaded data arrange to in on single assembly and define all necessary parts of electrically and arrange…

Answer:-  Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view which swon in below. First of all make one new product and rename in after that add flattening parameters into…

Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameter 10MM. Use the connectors provided.  First of all start to this challange download all cad data and routing mapping data. All connectors download from link and all file convert to electrically define and make them…

Week 4 Answer:- Route the following harness layout in Electrical workbench. Here Make assumption for harness bundle diameters are 15 mm . Use Following connectors as shown in layout diagram. Here Add protective covering on all branches connected to connectors and  Keeping end extremity at 30mm (from connectors end)…

                        Here Saw The P clamp,Backshell and Different types of Corrugated tubes In a week 3  we saw a p clamp to define electrically and here are some pictures of that  first of all we have cad data which shown in video anddownload from…

                                            WIRING HARNESS DESING IN CATIA V5-3D MODELING In Wiring Harness tutorial i have working on catia v5 sofwere. Catia v5 workbench use for all process which i followed…

SUNSEEKER PREDATOR YACHT   OBJECTIVE: The main aim of this project is to create a surface model of different yacht parts. To assemble the parts modeled using the SolidWorks 2021 software. To create a photorealistic model of the yacht and render the model using the SolidWorks visualize PART MODELLING: Part Modeling-parts…

Design, Assembly and Rendering of an American Chopper Motorcycle Using Solidworks   INTRODUCTION: Choppers evolved from bobbers in the 1940’s and 1950’s. The term “chopper” means to part off modify a motorcycle. However, over the years it has come to represent a particular style of modified…