Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge

AIM:- The aim of this project is to model a butterfly valve and to apply GD&T to the different parts of the butterfly valve and the assembly. Parts of Butterfly Valve :- Body of Butterfly Valve Shaft Retainer Disc  Lever Nut Screw Final Assembly 1.BODY OF BUTTERFLY VALVE: 1.Initially, the sketch for the body…

WIRING HARNESS FOR ENGINEAIM:To route the wiring harness for the given engine.Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design.Apply Protection coverings as required.INTRODUCTION:WIRING HARNESS OR CABLE HARNESS:A cable harness, also known as a wire…

AIM- To Route the Wiring harness on the Given car body Backdoor and prepare the flatten view drawing in CATIA V5. OBJECTIVE- The objective of this project is to route the wiring harness and prepare flatten view drawing for the Backdoor of the car. All types of packaging rules have to be considered while routing the harness…

AIM- To prepare a flattened-view of a previously created harness assembly. OBJECTIVE- The objective of this project is to create a flattened-view for a harness assembly and then place it on the drawing sheet. It is desired that the bundles with protective coverings are represented with different visuals on the…

OBJECTIVE: Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, CONTENT: Let, we have provided the harness layout as below and accordingly we have to route it. For that we have to make assumption for harness bundle…

AIM:Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram.Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end) Download connector…

AIM:To solve the above assignment questions and define the necessary electrical properties in the respective workbench. OBJECTIVE:To download the P-Clamp CAD data and define it as Electrical Support in the Electrical Part design workbench and also define the necessary electrical properties.To download the Backshell CAD…

AIM:  To define Electrical properties of the given components. OBJECTIVE: To download the CAD data of the parts from the given source. To define the Electrical properties correctly. To create catalogues of the components so that it can be used later. CATALOGUE DOCUMENT: First a new 'catalogue document' is created…

OBJECTIVE: To create a tooling axis and then check draft analysis for given class A surface. To create B&C Surface For a Given class A Surface then also check draft analysis. To develop all Engineering Features (Push clip, Dog House, Heat Stake, Flanges, Locator) For a given component. To create a parting lines…

AIM:Create the part models and assembly for the given drawings  DRAWING 1- QUICK RETURN MECHANISM: CADPART: BODY 1: BODY 2: BODY 3: BODY 4: BODY 5: ASSEMBLY WORKBENCH: VARIOUS VIEW: 2D DRAWING USING DRAWING WORKBENCH: BODY 1: BODY 2: BODY 3: BODY 4: BODY 5: ASSEMBLY DRAWING:     DRAWING 2- CV JOINT: CADPART:…

Objective: The main objective of this challenge is to create A PILLAR through understand the give master section To create solid body and B-side features for a given class A surface, by considering all the design parameters. PILLARS: A-Pillars straddle the windshield, B-Pillars are in the middle of the passenger compartment…

OBJECTIVE: Create the Door Trim Lower Plastic component through the given Class-A surface. To create the tooling axis for the plastic component To perform draft analysis over the plastic component. Create the Heat Stakes and the locators considering the design rules.   OVERVIEW: Initially, we need to offset the given…

Objective:  The main objective of this challenge is to create the B-side features Dog House for a given door trim. Overview:  Creating the class B and class C surfaces to the door trim, and creating the B side features (Dog House) by considering all the design parameters.  DOG HOUSE: Dog house is an…

Objective:  The main objective of this challenge is to create the B-side features RIBs and Screw Bosses for a given door handle. Overview:  Creating the class B and class C surfaces to the door handle, and creating the B side features (RIBs and Screw Bosses) by considering all the design parameters. Create the Screw boss…

 OBJECTIVE: Create the Core and cavity blocks for the switch bezel. CREATING A TOOLING DIRECTION: The base surface of the class - A was extracted and a point at the centre is created and an axis system was inserted to the point with the current feature is disabled. Then,using project intersection along yz plane…

OBJECTIVE: Create the Bumber Plastic component through the given Class-A surface. To create the tooling axis for the plastic component To perform draft analysis over the plastic component. OVERVIEW: Initially, we need to offset the given Bumber class A surface in the inner direction to the required thickness (here the…

OBJECTIVE: Create the Door Trim Lower Plastic component through the given Class-A surface. To create the tooling axis for the plastic component To perform draft analysis over the plastic component. OVERVIEW: Initially, we need to offset the given Door Trim class A surface in the inner direction to the required thickness…

OBJECTIVE: Create the Coin Holder Plastic component through the given Class-A surface. To create the tooling axis for the plastic component To perform draft analysis over the plastic component. CLASS A SURFACE:   CREATING A TOOLING DIRECTION: For this model, to use a line at mid-point of the base of the coin holder…

OBJECTIVE: To Create the Switch Bezel Plastic component through the given Class-A surface. To create the tooling axis for the plastic component To perform draft analysis over the plastic component. CLASS A SURFACE:   CREATING A TOOLING DIRECTION: The base surface of the class - A was extracted and a point at the centre…

OBJECTIVE: To create base bracket plastic component from the given class- A surface. To create the tooling axis for the plastic component To perform draft analysis over the plastic component.  CLASS A SURFACE: CREATING A TOOLING AXIS: Creating a point by using the centre hole axis. Creating the intersection boundary…

INTRODUCTI0N: A "back door" in a car typically refers to the rear passenger door or the rear cargo door, depending on the type of vehicle. which gives access for the boot space to store luggage, spare wheel etc. The doors can be operated mannualy or eclectric powered.In most of the luxuary car is electric powered. Basically…

INTRODUCTION: A roof in a car typically refers to the top part of the car that covers the passenger compartment. It can be made of various materials such as metal, plastic, or fabric, and can be fixed or retractable. The roof provides protection from the elements and can contribute to the structural integrity of the vehicle.…

AIM:         To Design The Front Fender Using Fender Skin Data.   OBJECTIVE:         Design the Fender with the necessary Mounting areas given below: Drip area A-Pillar mount Sill mount Bumper mount Baffel mount   INTRODUCTION:         Fender is the American English term for the part of an automobile, motorcycle or other…

                                                          Fender Design - Wheel Arch Challenge Aim:  To calculate the wheel arch distance from fender and to compare it with European standards.   Introdution: Wheel arch comes with some standard specifications. When viewed from the front or top side of the vehicle, if the…

Aim: To find the section modulus of the hood and optimization to improve the overall section modulus.   Objective: Use the section from your Hood design and calculate the section modulus using the formula S= I/y.   Section Modulus: Section modulus is a geometric property for a given cross-section used in the…

                                                     DESIGN OF HOOD USING NX CAD OBJECTIVE :           To design outer panel of Hood with Hem and develop the Inner…

 AIM :          To make a detailed report explaining about under-body coating, its types and its pros and cons by adding relevant images WHAT IS UNDERBODY COATING?         Underbody coating provides long term protection from corrosion to car's underbody. It also protects…

1. As I Suggest Car for Mr.D.S. Pughazhyendhii Under 8 to 10 Lakhs on Road for Official and Family Purpose Traveling Distance Around 500km.  Suggested Cars Listed Below:-  01. Hyundai Vennu.02. Honda Amaze.03. Tata Tiago NRG.04. Kia Sonet. 2.Benchmarking is defined as the process of measuring products,…