Week 9 - Attachment Feature Creation - Challenge 2

                                                                          UNDERBODY COATING      The underbody coating that…

                                                                                            …

                                                                                                                    DESIGN OF ROOF PANEL    An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Because…

                                                                                                                      FENDER DESIGN    A fender is the part of a car that protects and frames its wheels and keeps mud from splashing it. Most modern vehicles have fenders on their front wheels. When you get into a minor car…

                                                                                           …

WHEEL ARC AREA  The wheel arc area determines the horizontal gap between the fender and the wheel. These standards are set by different countries as the main purpose of this is for pedestrians safety. As we are dealing with European standards we have to look for the clearance it should be greater than 10mm. as you can…

BENCHMARKING FOR DESIGNING OUR PRODUCT WE HAVE TO CHOOSE THE CAR MODEL TYPE AND AFTER THAT WE HAVE TO DO A LOT OF MARKET RESEARCH REGARDING THE EXISTING PRODUCTS. THE MAIN OBJECTIVE OF BENCHMARKING OR "STRUCTURAL ANALYSIS" IS TO COMPARE OUR OWN IN-MAKING CAR  MODEL WITH EXISTING CAR MODELS OF COMPETITORS IN SUCH A…

Design and development of Hood outer and inner panel.(hemming part is remaining)     The Hood or we also called it the bonnet or engine compartment is an opening body panel that covers the engine in a front-engine vehicle. the hood is also considered as another type of door in a vehicle as it consists of an outer panel…

                                                                         DEVELOPMENT OF DOOR TRIM PANEL METHODOLOGY BEHIND DOOR PANEL Door…

AIM - TO DESIGN AND PERFORM DRAFT ANALYSIS ON DOOR ARMREST. OBJECTIVE:- WITH THE HELP TOOLING AXIS WE WILL PERFORM DRAFT ANALYSIS ON THE CLASS A SURFACE AND ON THE CLOSED SURFACE. WE WILL ALSO CREATE CLASS B SURFACE AND C SURFACE WITH THE HELP OF CLASS A SURFACE. METHODOLOGY:- FIRST WE WILL EXTRACT THE CLASS A SURFACE…

AIM:- TO CREATE B-PILLAR MASTER SECTION. OBJECTIVE:- TO CREATE A B PILLAR WITH THE HELP OF THE MASTER SECTION. IN THIS WE CREATE CLASS A, CLASS B, CLASS C SURFACE AND CLOSED CAD PART OF THE B -PILLAR. WE WILL ALSO ADD B-SIDE FEATURES TO IT. AND ALSO PERFORM THE DRAFT ANALYSIS FOR THE WHOLE CAD PART. A GENERAL IDEA ABOUT…

AIM:- TO CREATE 4 WAY LOCATORS, 2 WAY LOCATOR, AND HEAT STAKES ON DOOR APPLIQUE. ALSO, PERFORM DRAFT ANALYSIS ON THE COMPONENT. OBJECTIVE:- To create the 4 way and 2-way locators and heat stakes on door applique with the help of class a surface. the 4-way locators and 2-way locator will add up to the door applique and…

AIM:- CREATION OF DOG HOUSE AND SCREW BOSS ON THE COIN HOLDER COMPONENT. TO PERFORM THE DRAFT ANALYSIS ON DOG HOUSE AND SCREW BOSS AS WELL AS ON COIN HOLDER. OBJECTIVE:- The main objective is to create a dog house under design rules .the dog house should follow the design rules. also the creation of tooling axis and to…

AIM:-  To perform draft analysis on the coin holder rib design with the help of the tooling axis. Objective:- the main purpose of this project is to design a rib for the coin holder component considering all the design parameters which are required to design a Standard plastic product. we will discuss the design rules…

AIM:- To perform draft analysis on switch bezel design with the help of tooling axis. by with the help of the class A surface, we will make class B and class C surfaces and by making all of them we will go for the construction of the core and cavity for the plastic module switch bezel. Objective:-   Our main objective…

AIM:- To perform draft analysis on coin holder component. To create class B and C surfaces with the help of class A surface. Objective:- By creating tooling we will perform a draft analysis on the coin holder final component .then with the help of class A we will create a class B surface by extracting class A and then…

AIM: - To perform draft analysis on switch bezel design by combing class A, B, and C surface b using tooling axis. OBJECTIVE: - The main objective is to perform draft analysis with the help of using class a surface then with the help of class surface we create the class b surface and class c surface. after creating class…

AIM: - To perform draft analysis on Class A Surface with the help of tooling axis by using bisection method and to create class B and C surface with the help of class a surface. Objective: - The main objective is to perform draft analysis on class A surface with the help of tooling axis by using Bisection method .then…

AIM:- TO PERFORM DRAFT ANALYSIS ON FAN COVER OBJECTIVE:- THE objective is to perform draft analysis by creating a tooling axis for a Fan cover. With the help of the tooling axis, we have to perform a draft analysis on a fan cover. Procedure:- Design check First of all, we have to check the design of Class a surface by…