Week 8 - Challenge 5 - Core & Cavity Design

BOEING 747-8 DESIGN BY USING SOLIDWORKS OBJECTIVE:  The main ojective of this project is to design Boeing 747-8 Aircraft by using Solidworks Part and Surface Modelling Environment, and after completion of modelling, assembling the individual parts by using Solidworks Design Environment.  INTRODUCTION OF BOEING…

Define tooling direction Ans-The Tooling Direction is basically the direction that the mold pulls apart. The mold is built in two separate pieces, basically. You have a Cavity side and you have the Core side. The Core pulls apart from the Cavity and that's the Dyeline or the Tooling Direction. Write the definition…

Parametric_modeling_structure     Create a CATIA parametric structure with publication command          

Aim:-To get to know the types of converters used in HEV and EV vehicles. -To find the speed using torque-speed relation. - To get to know about induction and DC brushless motors.  Q1:-Which types of power converter circuits are employed in an electric and hybrid electric vehicle?   Ans:-There are two…

Aim:-To Write a Code On File Parsing Of Nasa Thermodynamic Data By Using Mat-Lab And Evaluate The Following Things:- Write a Function That Extract The 14 Coefficient And Calculate The Enthalpy(H),Entropy(s, Specific Heat (Cp) For All The Species In Data. Where R Is The Universal Gas Constant,T Is Temperature.The First…

Aim:- To understand the Speed control of a DC motor BJT-H bridge circuit. To study the Four-Quadrant Chopper DC Drive (DC7) block and compare it with the H bridge circuit. To do modifications in DC7 in order to get the EV cycle.   Q1.Run MATLAB demo ‘Speed control of a DC motor using BJT H-bridge’. Modify…

Aim:-To Use The Advisor Tool And Simulate The Given Questions. 1.For Ev_Defaults_In File, If Cargo Mass Is 500 Kg With All Other Default Conditions, Can The Vehicle Travel For 45 Km With Ftp Drive Cycle? 2.In The Above Case, Try Changing The Battery Capacity And Repeat The Simulation. 3.Perform Gradeability Test With Prius_Jpn_Defaults_In…

  Aim:-1.To Make a Simulink Model Of Doorbell Using Solenoid Block Where The Switch Is Closed For 2 Second And Then Released.& Observed The Movement Of Plunger. Use a Thermistor To Sense The Temperature Of a Heater & Turn On Or Turn Off The Fan As Per The Following Conditions: Temperature Source:20C From 0to…

AIM:- 1.To Implement a control logic of a “washing machine” using Stateflow as per the given sequence:  If the power supply is available, the system gets activated  If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by Washing…

  Aim:-To Write Code in mat-lab to optimize the stalagmite and find global maxima of the function. Theory:-  Genetic Algorithm:- Is a Method For Solving Both Constrained And Unconstrained Optimization Problems That Is Based On Natural Selection, The Process That Drives Biological Evolution. The Genetic Algorithm…

Aim:- To Write a Program In Mat-Lab That Will Simulate The Pendulum Motion. Objective:- The Objective Of The Program Is To Simulate The Motion Of Pendulum With Give Values. Gravity g=9.81(m/s) Length Of Pendulum l=1(m) Mass of ball =1(kg ) Damping coefficient,b=0.05(kg/s) Total Duration t=20(s)   Initial Condition…

Aim: To create an outer and inner hood panel, positioning the stiker, hinge and their reinforcements. Data to be used: Hood Thickness Information Outer Panel Thickness = 0.75mm Inner Panel Thickness = 0.75mm Reinforcement Thickness = 1.5mm Master sketch:                    …

OBJECTIVE:- Class A Surface Was Received From The Styling Team. My Objective Is To develop the Class A Surface Received into Manufacturable Product Design Following The OEM Design Standards Using CATIA V5 Surface Workbench. SUMMARY:- The Project Report explains, in brief, the Design life cycle followed in the automotive…

Aim: To design & develop the Roof of a car with its components by following the master section and design parameters. Objective: To develop the essential flanges and reinforcements using roof styling as input. To do a curvature study on the roof and perform calculations to determine the position of the Bow-roof. To…

OBJECTIVE:-  Class A Surface Was Received From The Styling Team. My Objective Is To develop the Class A Surface Received Into Manufacturable Product Design Following TheOEM Design Standards Using CATIA V5 Surface Workbench. SUMMARY:- The Project Report explain in brief the Design life cycle followed…

OBJECTIVE:- The objective of the project is to design a Body in White front Fender of a car with its mountings using the information provided by the styling team. The Skin data and Master sketch are the information provided by the styling team. INTRODUCTION:- -Fender is the American English term for the part of an automobile,…

Aim:-To Calculate the section modulus for the previously designed hood and optimized hood.& To Come up with the new section that has improved section modulus of the previous section. Introduction: Section properties involve the mathematical properties of structural shapes. They are of great use in structural analysis…

Aim:-1.To Evaluate The Hill Climbing Ratio Of Tata Ultra-Truck At Fully Loaded Conditions.  2.Analyse The Grade-Ability And Its Associated Parameters. 3.Analyse The Force Acting On The Vehicle By Creating a Drive Cycle And Plot Graph Of Speed Vs Time.4.Modeling Of Wot (Wide Open Throttle)Of Gm Ev1 Car And Compare…

Q. For The Given Component, Check The Geometrical Error Meshing With The Give Element Quality Criteria. After Meshing the Component the Thickness Has to Be Assigned .Write A Detailed Report on Your Process and Also Mention Which Method You Used to Extract the Mid-Surface Along With the Reason. SR.NO. QUALITY CRITERIA VALUE…

For The Given Component, Check The Geometrical Error Meshing With The Give Element Quality Criteria. After Meshing The Component The Thickness Has To Be Assigned .Write A Detailed Report On Your Process And Also Mention Which Method You Used To Extract The Mid-Surface Along With The Reason. Sr.No. Quality Criteria Value…

Aim:-To Design B-Pillar  Through Master Section Development And Write a Detailed Report. Given: -A-Surface  -Master Sections  -Distance Between Ribs Should Be 50mm  -B-Pillar The B-Pillar Is The Central Pillar Of The Car. This Pillar Is Actually a Sheet Metal Part Which Is Welded…

Aim:-  To Create the Core and cavity blocks for the switch bezel designed.   -All views of switch bezel ( Final surface) -All views of switch bezel ( Solid body)with Draft analysis at 2.5degree with 2.5mm thickness     -Core and Cavity blocks for the switch bezel designed

Aim:- To Write a Program In Mat-Lab That Will Simulate The Pendulum Motion. Objective:- The Objective Of The Program Is To Simulate The Motion Of Pendulum With Give Values. Gravity g=9.81(m/s) Length Of Pendulum l=1(m) Mass of ball =1(kg ) Damping coefficient,b=0.05(kg/s) Total Duration t=20(s)   Initial Condition…

Aim:-To Plotting Pv Diagram For Otto Cycle And Calculating The thermal Efficiency Of Otto Cycle By Using Mat-lab. Theory:-An Otto Cycle Is An Idealized Thermodynamic Cycle That Describes The Functioning Of a Typical Spark Ignition Piston Engine.It Is The Thermodynamic Cycle Most Commonly Found In Automobile…

Aim:-To Write A Mat-lab Program On Forward Kinematics Of A 2R Robotics Arm And Creat A Animation File. Objective:-Our Main Objective Is That How The End Effector Varies With Different Value Of Theta For Both Link So That We Could Get The Required Work Space Of Manuplatar And Make Animation Of 2R Robotic Arm. Theory:- A…