Week 5 Challenge : Surface wrap on Automotive Assembly

AIM:

        TO THE GIVEN MODELS, CHECKING THE GEOMETRICAL ERRORS AND DELETE SURFACE WHICH ARE UNWANTED FOR SURFACE WRAP. AFTER CLEARING THE GEMOTRY, MERGE ALL 3 MODELS AND PERFORM SURFACE WRAP.

PROCEDURE:

INTIALLY, DOWNLOAD ALL THE MODELS GIVEN IN CHALLENGE 

• FIRST IN THE ENGINE MODEL IS TAKEN TO CLEAN THE GEOMETRIC 
  
• HERE, THERE ARE MANY UNWANTED GEOMETRICS ARE THERE SO, WE NEED TO CLEAN OR DELETE DIRECTING THE LIKE UNWANTED RINGS AND DONUTS.
  
• FOR, DELETING THE ALL UNWANTED GEOMETRICS AND SHAPED WE CAN USING THE NOT OPTION AND HIDE THE ENGINE PARTS BY ENABLING THE PID REGION.
           
• BY CLICKING THE ALL ENGINE PARTS AND HIDED 
  
  
• NOW WE CAN DIRECTLLY DELETE THE ABOVE GEOMETRIC USING THE DELETE OPTION
  
• AFTER DELETING THE MAXIMUM UNWANTED GEOMETRICS IT WE LIKE THIS,
  
• THEN, NOW WE SHOULD CLEAN UP OUTER SURFACE RED COONS AND BLUE COONS ARE BEEN CLEANED.
  
  
  
• LIKE THIS ALL THE BLUE COONS ERRORS ARE CLEANED UP FOR THE BLUE COONS.
• THEN RED COON ARE ALSO CLEANING USING THE NEW CREATING THE SURFACE
  
  
• ONLY THE OUTER SURFACE IS CONSIDERED BECAUSE WE ARE DOING THE SURFACE WRAPING THE IT DOES NOT NEED THE INTERNAL ERRORS.
• AFTER DOING THIS THE ENGINE MODEL WILL LIKE THIS BELOW.
  
• AFTER, THIS WE NEED TO CLOSE THE ALL OTHER HOLES AND OPENING IN THIS ENGINE. 
  

NOW WE CLEAN UP THE NEXT MODEL TRANSMISSION UNIT 

• WHEN WE OPEN THE MODEL,
  
• NOW HERE ALSO WE NEED TO CLEAN UP ALL OUTER RED AND BLUE COONS
  
  
  
  
  
  
• AFTER THE CLEANING UP MODEL THE MODEL WILL LIKE THIS BELOW,
   
   

NOW THE NEXT MODEL IS GEAR BOX MODEL.

• AFTER OPENING THE MODEL THE IT WILL LIKE THIS,
  
• HERE ALSO THE CLEANING UP THE MODEL IN OUTER SURFACE ONLY 
  
  
  
• AFTER CLEANING THE RED AND BLUE COONS THE MODEL WILL LIKE THIS,
  

AFTER CLEANING UP ALL THE MODEL GEOMETRIC ERROR NOW WE NEED MERGE THE TRANSMISSION UNIT AND GEAR BOX.

FOR MERGING THE MODEL,

• GO TO THE OPEN AND CLICK THE MERGE.
  
• THEN IN THAT POP WINDOW,SELCET MODEL THE TRANSMISSION MODEL.
  
  
• DO NOT CLICK THE OK, CLICK CANCEL.
• THEN SAME FOR THE GEAR BOX MODEL ALSO DONE 
  
• THEN ALL OPENINGS ARE CLOSED IN ASSEMBLED MODEL USING THE NEW TOOL OPTION THE SURFACE HAVE BEEN CREATE.
  
• AFTER DOING THIS , THE UNWANTED ASSIGNED PIDS ARE DELETED USING THE COMPRESS TOOL.
  
  
• AFTER COMPRESS, THE CLICK THE CLASSIC MESH THEN IN ELEMENT THE WRAP OR IN THE OCTREE THERE IS ALSO WRAP.
  
• WHILE CLICK THE POP WINDOW SHOW THE CONSTANT WRAP OCTREE AND ASSIGN THE EMPTY ONE IN STATUS 
  
• THE UNTITLED PARAMETER ARE DONE.
  
• MESH LENGHT IS 5mm IS GIVEN.
  
• THEN CLICK CONTENT AND THEN SELECTE ALL THE PIDS AND CLICK THE GREEN ARROW AND CLICK OK.
  
  
• AFTER DOING THIS CLICK RUN THE CONSTANT WRAP OCTREE.
  
• NOW THE SURFACE WRAP DONE 
  
  
  
  
  
  
  
  
  
  
  

LEARNING OUTCOME:

• WRAP TOOL 
• CLEARING THE UNWANTED STRUCTURES
• MERGE OPTION IN FILE 

RESULT:

AS THE GIVEN MODELS ARE CLEARED THE GEOMETRIC ERROR AND DELETED THE UNWANTED SURFACES IN ALL MODEL AND THEN TRANSMISSION MODEL AND GEAR BOX MODEL ARE MERGED IN THE ENGINE AND USING THE WRAP TOOL THE SURFACE WRAP IS DONE THE TARGET LENGTH AS THE 5mm.
 

HERE IS LINK FOR ENGINE ASSEMBLY SURFACE WRAP 

CLICK HERE FOR THE MODEL