REVIT_Creation of Basic Drawing_Week 2

QUESTION : Consider the structure as cladded by steel sheeting and Grade A material is used according to IS 2062 Consider Live, Dead, Wind, and Seismic loading. Even though the height does not exceed 10m, the analysis and manual calculations of wind load need to be done For load calculation kindly refer to IS Codes …

QUESTION :  Develop general arrangement for the RC office building. Analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. The building to be designed for dead, live, wind and seismic loading. Report of each member to be generated and extract drawings…

Q1 )   Generate report for the steel building design from challenges 1 – 6 along with the loading summary. ANS 1) AIM : To generate report for the steel building design from challenge 1-6. TOOLS USED : Report. Model report. Show report. PROCEDURE : 1. Open the structure and analyze it.   2. Now click…

Q1 )  Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations). ANS 1) AIM : To design the slab and roof foundations of the model and to outline the thought process for designing of the elements. TOOLS USED : Design. Settings.…

Q1)  Based on the analysis design RC column and beam. ANS 1) AIM : To design RC column and beams based on the analysis. TOOLS USED : Review. Check member. Static. PROCEDURE : 1. First we have to open the file in which we have completed the structure.   2. Next we have to validate the model in search on any…

Q1 ) Generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly. AIM : To generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly. TOOLS USED : Load. Loadcases. Seismic wizard. Seismic load. PROCEDURE…

Q1 ) Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load ANS 1) AIM : To calculate the dead load based on the design and apply it on the structure. TOOLS USED : MS Excel. Loads. Loadcases. Dead load. Area.…

Q1) Setup model for RC building design and based on following parameters for cover. ANS 1)   AIM : To setup model for RC building design and based on following parameters for cover.   TOOLS USED : Tekla software. File. Settings. Structural Defaults.   PROCEDURE : 1. First open a new tekla file for starting…

QUESTION )   Analyze and design a steel building to 10T CRANE as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. Provide bracings and moment connection for lateral stability.  Consider dead, live, equipment and wind loading. Consider the brick wall loading for 150mm…

Q1 ) Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model. ANS 1) BENDING MOMENT :  The bending moment can be defined as the bending effect which is caused due to any internal or external force. It is only of the important concept to be studied and…

Q1 )  Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 ANS 1 : AIM:   Generate manual wind loading in the design report based IS code as per the following input TOOLS USED : Excel. IS codes. Calculator. PROCEDURE :…

  QUESTION )   Create a G+4 Residential building as per NBC standards and make it a central model file. Your model should contain: The sloped roof at the top level of the building (10 degrees) Architectural components including furniture and home appliances Room tags and Annotations Section cut through each…

QUESTION 1)  Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. ANS 1) AIM : To usse the architecture/structural project file developed from week 6-8. Export…

QUESTION 1)  Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. ANS 1) AIM :   To create a seet of sinusoidal points and create a curve and create a surface out of the curve. TOOLS USED : Dynamo. Code block. Range. Mat.sin. Integer slider. Product…

QUESTION 1 )  Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? ANS 1 )          With the help of revit we can draw, design and model a structure. Only designing or modeling is not the task, we have to follow some basic set of rules and regulations…

QUESTION 1)     Based on the project saved from Week 3, proceed from First Floor Level .Model a Ceiling from architecture tab above the walls at first floor level. ANS 1) AIM :       To model a celing to the previously created project with the help of architectural tab above the walls…

ANS 1) AIM :            Based on your previous layout add floor using floor option from architecture tab and set the thickness, and draw the grids for the ground plan. TOOLS USED :  Architecture. Floor. Levels. Grids. Material. Thickness. Property browser. PROCEDURE : Open the project…

ANS 1)     AIM:           To form a file menu, create a new project and name the project appropriately.     TOOLS USED: Revit software. file new project     PROCEDURE :  First open revit 2019 software. Then click on file menu and drop down box appears. Then click…

ANS 1)         BIM stands for Building Information Modeling. It is a very effective and advanced software which plays a vital role in drafting and planning softwares. BIM is a 3D modelling software which helps us in understanding and explaining about the project. BIM was invoked by autodesk and we can…

QUESTION 1)    Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout   …

QUESTION 1)   What are HVAC systems ? Why are they essential in modeling of buildings? ANS 1)         HVAC system is one of the important component in the modeling of a building. The term HVAC stands for Heating, Ventilation and Air conditioning. Now lets get into these terms, Heating…

QUESTION 1)  Select the type of structure you want to build from one of the three below        a. Multi Unit Residential Apartment        b. Office Buildings        c. School ANS 1)      From the above given options the type of structure…

QUESTION 1)   Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project. ANS 1) AIM :  To open an architectural tab and set project base point and project shared cocordinates using manage tab for the project. TOOLS USED : Collaborate.…