Week 1 Understanding Different Battery Chemistry

Q. In a laboratory experiment, data of voltage and current has been recorded and the same is attached in an excel file ( VI.xlsx ). Read the excel file in the Matlab program and perform the interpolation in the range of -17.3:0.1:0.9. Generate the interactive plot for the interpolated data. Additionally, compute the current…

Q. Create a MATLAB model of electric car which uses lithium ion battery and suitable motor. Choose suitable blocks from Simscape or Powertrain block set. Implement the vehicle speed control using PI controller and generate brake and accelerator commands. Avoid using readymade driver block for speed control. Prepare a report…

Q. Create a detailed MATLAB model of an electric rickshaw (three wheel passenger vehicle) as per details below:  Rear wheels driven by PM brushed type motor Assume efficiency points of motor controller and motor Make an excel sheet of all input and assumed data  Results: For any three standard driving cycles…

ANS : Introduction to the Feature: The Highway Assistant supports the driver and takes over the longitudinal and lateral guidance of the vehicle in monotonous driving situations on highways. The partially automated function can automatically start, accelerate, brake as well as steer the vehicle to a certain extent. The…

ANS : Traffic Jam Assistant Feature Introduction to the Feature: Traffic Jam Assistant is one of the most common feature in Advanced Driver Assistance System. Traffic Jam Assistant helps the driver arrive more relaxed at their destination, even in dense traffic or in traffic jams. As a partially automated comfort function,…

                                                       STUDENT OF ONLINE EV BATCH 16  ANS : OBJECTIVE : Developing Adaptive Cruise Control feature as per the Requirement…

                                                                     STUDENT OF ONLINE EV BATCH 16 ANS : OBJECTIVE : Development of MATLAB Simulink model as per requirement. Tag the requirements to the simulink model; tagging requirement 1 & requirement 2 to their corresponding subsystems. MBD compliant changes, Data Dictionary…

                                                                            STUDENT OF ONLINE EV BATCH 16 ANS : For a 10 cell series…

                                                                                 STUDENT OF ONLINE EV BATCH 16  ANS : Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions. Cell: ANR26650M1-B                                           …

                                                                            STUDENT OF ONLINE EV BATCH 16 ONLY QUESTION NO. ONE WAS TOLD TO COMPLETE. ANS 1 : 1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results. https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms…

                                                                          STUDENT OF ONLINE EV BATCH 16 ANS 1 : 1. Prepare a table which…

                                                                                STUDENT OF ONLINE EV BATCH 16 I don't…

                                                              STUDENT OF ONLINE EV BATCH 16                     …

                                                                  STUDENT OF ONLINE EV BATCH 16 ANS 1 : 1. For a defined driving cycle, calculate the…

                                                                 STUDENT OF ONLINE EV BATCH 16 ANS 1 :      A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.     B. Comment on the armature current shoot-up from the scope results.     C. Refer to the help section of ‘The Four-Quadrant…

ANS 1 : 1. Which types of power converter circuits are employed in electric and hybrid electric vehicle?   Power Electronic Converters :  In Electric and Hybrid Electric vehicle (EV/HEV), the power electronic convertors are considered as the key elements that interface their power sources to the drivetrain…

                                                        STUDENT OF ONLINE EV BATCH 16  ANS 1 : 1. For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations. In the ADVISOR Vehicle input GUI select Load File as 'EV_defaults_in…

                                                   STUDENT OF ONLINE EV BATCH 16 ANS 1: What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type? MAPPED MODEL :  1. The mapped model is one type where the data points are pre_assigned in lookup tables. 2. The Engine…

Aim : To study and analyze the BAJA All - Terrain Vehicle(ATV) using MATLAB Simulink. Objective : To carry out a system-level simulation of an all-terrain vehicle and prepare a technical report explaining the model properties & comments on the results. 1. Study the Baja ATV model without a Dashboard. 2. Study…

Ans 1: Aim :   Implement control logic of a “washing machine” using Stateflow as per given sequence:  If the power supply is available, the system gets activated  If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by…

Ans-1: Objective : To simulate a model of doorbell using a solenoid and to create a situation where the switch is closed for 2 seconds and then released and also to observe the physical movement of the plunger. Blocks Used : Solenoid, Battery, Mechanical translatonal reference, Electrical Reference, Solver, Simulink-PS…