Underbody Coating

AIM: To design an automotive BIW front fender using Siemens NX - CAD INTRODUCTION: Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being…

  PLEASE FIND THE REPORT IN ATTACHED DOC BELOW. DUE TO ISSUE WHILE SUBMITTING THE CHALLANGE I AM ATTACHING THE REPORT TO THIS GIVEN ANSWER SPACE.

1. QUICK RETURN MECHANISM: A quick return mechanism is an apparatus to produce a reciprocating motion in which the time taken for travel in return stroke is less than in the forward stroke. It is driven by a circular motion source (typically a motor of some sort) and uses a system of links with three turning pairs…

AIM : To design and assemble the roof of a car.  OBJECTIVE: We were given class A surface of the roof and our task in this particular project is to model the entire roof with the help class A surface and also model the roof reinforcements based on the master sections, dimensions and parameters given to us. Also I…

AIM: To Calculate the Wheel Arch gap from front fender at required points and  check whether the car passes the European standards. INTRODUCTION: Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary…

AIM: To perform section modulus calculation and design optimization for BIW hood component. INTRODUCTION: Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. Other geometric properties used in design include area for tension and shear, radius of gyration for…

AIM: Design and assembly of BIW Hood using NX-CAD application.  INTRODUCTION: The hood (American English) or bonnet (Commonwealth English) is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment, or trunk (boot in Commonwealth English) on rear-engine and…

UNDERBODY COATING: Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years, it’s…

BENCHMARKING : Benchmarking is the practice of comparing business processes and performance metrics to industry bests and best practices from other companies. Dimensions typically measured are quality, time and cost.Benchmarking is used to measure performance using a specific indicator (cost per unit of measure, productivity…

TITLE: METAL BRACKET DESIGN USING NX-CAD SHEETMETAL APPLICATION OBJECTIVE: The main objective of this project is to model the sheetmetal part (METAL BRACKET) and perform various sheetmetal operations using NX-CAD sheetmetal application to obtain the final output. INTRODUCTION: Metal Bracket is an intermediate component used…

 TITLE: BRACKET DESIGN USING NX-CAD SHEETMETAL APPLICATION OBJECTIVE: The main objective of this project is to model the sheetmetal part (BRACKET) and perform various sheetmetal operations using NX-CAD sheetmetal application to obtain the final output. INTRODUCTION: In this project intially I have created  a…

TITLE: CASING DESIGN USING NX-CAD SHEETMETAL APPLICATION OBJECTIVE: The main objective of this project is to model the sheetmetal part by using sheetmeetal tools and also to model with appropriate dimensions. INTRODUCTION: Creating fast, accurate flat patterns is the goal of any organization that manufactures products…

TITLE: MODELLING, ASSEMBLY AND RENDERING OF AN AMERICAN CHOPPER USING SOLIDWORKS OBJECTIVE: The main objective  of this project is to perform 2-D and 3-D part modelling of individual parts of an ‘American Chopper’.​ Further after successfully completing the respective modelling…

TITLE : DESIGN OF ODD SHAPED ENCLOSURE USING NX-CAD SHEETMETAL APPLICATION OBJECTIVE: The main objective of this project is to model the sheetmetal part by converting a solid model into a sheetmetal model and perform various sheetmetal operations using NX-CAD sheetmetal application. INTRODUCTION: In this project intially…

TITLE : DESIGN OF BOX ASSEMBLY USING NX-CAD SHEETMETAL APPLICATION OBJECTIVE: The main objective of this project is to model the sheetmetal part by using sheetmeetal tools and also to model with appropriate dimensions. INTRODUCTION: Creating fast, accurate flat patterns is the goal of any organization that manufactures…

  TITLE: MODELLING AND ASSEMBLY OF YACHT USING SOLIDWORKS OBJECTIVE : The main objective of this  project is to model the individual parts of an yacht and assemble them as a single model using SOLIDWORKS software. After the assembly I have tried to create a background scene and a photo-realistic rendering using…