Underbody Coating

MODELING AND REBDERING OF AMERICAN CHOPPER USING SOLIDWORKS OBJECTIVE: The main objective of this project is to model different parts of a custom designed American chopper using SOLIDWORKS. To assemble the different parts modeled for the American chopper. To create a photo-realistic view of american chopper by rendering…

AIM: To Design the outer upper and lower panel, inner panel with the necessary reinforcements by following the Master section with the design parameter for the given class A surface.  INTRODUCTION: A door is a hinged part which is used for entry and exit of the vehicles. Back doors are one of the type doors of the…

ROOF DESIGN OBJECTIVE: • The objective of this project is to design car roof with essential flanges and reinforcements like ditch area,front roof rail, bow roofs, central roof rail and rear roof rail for the the given styling surface • Perform a curvature study on the roof and perform the calculations for the…

FENDER DESIGN OBJECTIVE: The main objective of this project is to design a fender using a new age design software - NX - CAD INTRODUCTION: Design of any product starts from an requirement. The design engineer sketches the product based on the the requirement. Then the 2D sketch with the proper dimensions is converted into…

                                                    SECTION MODULUS OF AN HOOD • Section modulus is a direct measure of strength of any sectional area of an object about an referenceaxis(neutral…

1. Wheel Arch: • Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. • The design of Wheel arch of a fender should be such that it must shield wheels and protect both passengers' compartment and pedestrians from projection of water, mud and stones. • For the vehicle…

INTRODUCTION Car's hood panel plays a vital role in asthetics and safety of padestrians. Hood panel is important component in BIW which consists of two panels Outer panel and inner panel and both are hemmed.                                …

Underbody Coating A car body or a BiW is constructed with several metals like steel, aluminum, etc. So as per the nature of metals, they react with oxygen & water (or air moisture) resulting in corrosion which is not favorable to the automotive industries & their customers. So, in order to prevent the corrosion…

AUTOMOTIVE BENCHMARKING Benchmarking is the process of comparison of similar products on some dimensions of performance Automotive Benchmarking is the process of analyzing the choices of similar products based on the selection factor and deducing it to final conclusion.   REPORT The above case of Mr. Pughazhyendhii…

HERE I CREATE COMPLETE MOLD FOR CPU FAN BEZEL IN WHICH I'LL CREATE INSERT, HOLE FOR NUT TO HOLD INSERT, SLIDERS, WASHERS, SPACE FOR WASHERS IN CORE AND CAVITY, SPACE IN CORE FOR LOCKING MECHANISM, SPRUE, RUNNER, GATE, AIR VENTS. 1. SCALE First step in creation of mold is to scaleing component as per it's shrinkage value…

Following parts were created in this week :- 1. Ejection system with ejrctor pin and plates. 2. spure in cavity and runner & gate. 3.air vent in core 4. cooling channels in core  

Following steps were followed. 1. 1st create a slider for the undercuts. 2. then create a another slider for undercuts. 3. create washer for slider. 4. then finally create a insert and there bolts.  

MOLD DESIGN, SLIDERS & EJECTION PINS CREATION FOR TABLE FAN BASE USING SOLIDWORKS In this report mold design, creation of ejection pins and sliders for table fan base was done by creating each individual part in assembly workbench following step by step process to attain best results. As there was the necessity of…

Following steps are follow during the assignments:- 1. Open priviously made core and cavity blocks 2. draw the slider where the undercuts are present. 3. draw the coller for the slider 4. draw the washer, nut and bolts .

1 MODELING AND RENDERING OF AN YACHT 2 OBJECTIVE . Model the diffrent parts of an yacht using solidworks. • Assemble the parts of yacht. • To create photo relistic view of an yacht by rendering the model using solidworks photo view 360 3 PART MODELING Part modeling in general means to create a virtual prototype…