Underbody Coating

SECTION MODULUS Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. Other geometric properties used in the design include an area for tension and shear, the radius of gyration for compression, and moment of inertia and polar moment of inertia for stiffness.…

BACK DOOR  Backdoor are one of the type of door of the vehicle which are located next to the passanger seat which provides access to the luggage compartment. In the most of the cars, these back door are operated with the help of gas stay which in turn reduces the effort required to lift the door. Car doors may be manually…

ROOF  An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Because the earliest automobiles were designed in an era of horse-drawn carriages, early automobile…

FENDER A fender is different than a bumper because it's a metal structure that frames the wheel well of your car, instead of the front or back. The fender extends between the front door to the front bumper covering the front wheels of the vehicle. For vehicles with a narrow car body that exposes the tire, the fender…

AIM: To Calculate the Wheel Arc area and prove whether the car will pass the standards  WHEEL ARC:  Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. The main intention for the calculation of wheel arc radius is to position the wheel inside the fender body, because…

AIM: To create the Core and cavity blocks for the switch bezel designed TO DESIGN: >Tooling axis >Class B surface  >Class C surface >Solid surface CREATION OF TOOLING AXIS: >The tooling axis is created by the bisecting method >The base of the class A is extracted and create a centre point in…

part 1 part 2 part 3 part 4 part 5    

Aim To create B pillar with the given master section Input  Class A Master section for flange, dog house, 4 way located.    Flange In the B pillar the flanges are created through the master section. We need to create a boundary Then sweep it by 3 deg with tooling axis as draft direction      …

AIM: To create  the Door Applique Plastic component through the given Class-A surface TO DESIGN: >Tooling axis >Class B surface  >Class C surface >Solid surface CREATION OF TOOLING AXIS: >The tooling axis is created by the bisecting method >The base of the class A is extracted and create…

AIM: the boss and Dog House for the Centre console coin holder considering the design rules To create  TO DESIGN: >Tooling axis >Class B surface  >Class C surface >Solid surface CREATION OF TOOLING AXIS: >The tooling axis is created by the bisecting method >The base of the class A is extracted…

AIM: To create the rib for the Centre console coin holder considering the design rules  TO DESIGN: >Tooling axis >Class B surface  >Class C surface >Solid surface CREATION OF TOOLING AXIS: >The tooling axis is created by the bisecting method >The base of the class A is extracted and create…

AIM: to create Coin Holder Plastic component through the given Class-A surface and create tooling axis to do draft analysis. TO DESIGN: >Tooling axis >Class B surface  >Class C surface >Solid surface CREATION OF TOOLING AXIS: >The tooling axis is created by the bisecting method >The base of…

AIM: To create a design Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model  TO DESIGN: >Tooling axis >Class…

AIM: To Create the Base Bracket Plastic component tooling axis. PROCEDURE FOR TOOLING AXIS : *first step is to create a tooling axis , to create it we create a dummy tooling axis *second step is to get a bisecting line  then that line will be the tooling axis *here in this case viewing from z direction we can…

WHAT IS HOOD  A car hood also referred to as a bonnet in some other countries is the hinged cover that rests over the engine of a front-engine vehicle. Its purpose is to provide access to the engine for repair and maintenance. Car hoods are typically constructed from steel and sometimes from aluminum.On…

UNDER BODY COATING : Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years,…

BENCH MARKING Bench marking involves a structured comparison between similar products, services or processes on some dimensions of performance. For example it can be used to compare the availability and delivery of features in a product and in this form often provides the basis of consumer tests and reviews. These look…

AIM To create a door interior part from the inputs of class A surface along with master section by following the design rules followed inindustries in catia v5 SOFTWARE USED CATIA V5 OBJECTIVES • Create a sketch by using Positioned sketch . All the should be sketches should be Iso-Constrained   • Ensured…

    AIM: To do a draft analysis in a surface of fan cover and understand the drafting. PROCEDURE: First we should check whether the cad part is a single cad ore multi.. to check this we can use 'Join' or 'Boundary' tool Next step is to  create a 'intersect' line  Throught the intersect lines we create…

%stalagmite function function s = stalagmite(vector) x= vector(1); y= vector(2); f1x = (sin(5.1*pi*x+0.5).^6); f1y = (sin(5.1*pi*y+0.5).^6); f2x =exp(-4*log(2)*((x-0.0667).^2)); f2y =exp(-4*log(2)*((y-0.0667).^2)); s =-(f1x.*f1y.*f2x.*f2y); end %main code ga clear all close all clc %values for x and y x = linspace(0,0.6,150);…

%main program clear all close all clc %opening the data f1= fopen('THERMOS.DAT','r') %reading the header files b1 = fgetl(f1) global_temp = fgetl(f1) %getting the global temperature temp_range = strsplit(global_temp,' ') %changing the values into numbers global_lt = str2num(temp_range{2}) global_mt = str2num(temp_range{3})…