Roof Design

AR BACK DOOR DESIGN Aim: To design back door of car using given outer class 'A' surface. What is back door of a car? A door which is located at the rear side of a car which gives access for the boot space to store luggage, spare wheel etc. These doors can be operated manually or electric powered. In most of the…

OBJECTIVE:           1.Main objective of the project is to create the Roof Sheetmetal design in NX cad, and also designing Front roof rail, rear roof rail, bow roof front, bow roof rear, center roof rail and Reinforcement are creating to build the strong roof.          …

AIM : From the given CLASS A SURFACE of the FENDER we have to made changes in the design and develop the model with some extra features that are : Mounting Area Bumper Drip A Pillar Sill Baffel Introduction: Fender: Fender is a part of the vehicle that frames the wheel . The primary purpose of the fender is to prevent…

Aim :  To Calculate the Wheel Arch gap at required points and check whether the car passes the European standard.     Fender Arch :   Wheel arch is the semi circular part of the fender positioned above the wheel of the vehicle . The design of the wheel arch of the fender should be such that it must shield wheels and protect…

Aim To calculate section modulus of hood and optimize the design to have improved section modulus.     Section modulus:- Section modulus is a direct measure of a strength of any cross sectional area of an object about an reference axis. The formula of section modulus is given by, S=I / Ymax Where, I = Moment…

HOOD DESIGN- CHALLANGE Introduction:- Hood is main component of a car at the front portion. It is used to decorate the car & add luxurious look. The shape of the bonnet is made aerodynamic in order to minimize the air effect. Hood design consideration:- The hood of a car is considered as the frontal BIW enclosure component.…

Development of a Door Trim panel - Final project Aim: In this project we create the door trim panel Components that is (Lower substract,Arm rest, Bottle holder, map pocket) with the necessary input surfaces provided and generating the necessary B side features ( heat stakes, 4 way locators, Dog houses, push clips, Ribs,…

UNDER BODY COATING : Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years,…

BENCHMARKING Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying companies with superior…

A-PILLAR DESIGN WITH MASTER SECTION   AIM: To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. CLASS A SURFACE:           Class…

Objective: The main aim of this challenge is to create a solid body of 'Door Trim Lower' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Door trim. Overview:Initially, we need to offset the given…

Dog house design for the Door Trim:   Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis. Objective: Create the Tooling axis  Design the class-B and class-C surfaces and…

AIM   To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.     Tooling Axis creation: It is defined…

BUMPER Object :- Create a tooling axis in proper way for finding better draft analysis from given class A surface. Create draft analysis of class A surface and create class B and class C surface from class A surface. And finally create draft analysis of finished body. Consider the thickness of the component 3…

Aim: To create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. REPORT ON DRAFT ANALYSIS: INTRODUCTION: CLASS-A SURFACE: a…

REPORT ON ASSEMBLY WORKBENCH DRAWINNG 1 QUICK RETURN MECHANISM     COMPONNENTS MADE BODY 1 BODY 2 BODY 3 BODY 4 BODY 5 STEPS FOLLOWED STEP 1 ADDING  BODY 2 AND I MADE THIS PART AS FIX PART BY USING FIX CONSTRAINTS . STEP 2 THEN AFTER I ADD BODY 2 AND MADE IT REVOLVE AROUND THE FIX PART BY USING SURFACE CONTACT…

REPORT ON Assemble and apply GD&T to the butterfly valve assembly drawing TREE TABLE -   FOLLOWED STEPS STEP 1.- STEP 2.- STEP 3.- STEP 4.- STEP 5.- STEP 6.-   STEP 7.-   ISOMETRIC VIEW   FRONT VIEW     SIDE VIEW     TOP VIEW