Roof Design

AIM : The objective of this project is to design a butterfly valve and apply GD&T to it's components and final assembly using Siemens NX.     INTRODUCTION  A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the…

AIM :- To create a CAD model for door trim panel's parts by considering the given inputs of class A surface along with master section by following the design rules followed in OEM and tier1 companies.   Objectives :-   To create individual tooling axis for the parts and perform draft analysis on…

OBJECTIVE: To create the Door Trim Lower's Plastic Component using the Class A Surface that is provided. Desired Thickness of the Plastic Component is 2.5mm with 3.2 degrees as the Draft Angle. Firstly, we have to create the required Tooling-Axis for…

4 Bar Quick Return Mechanism: First we have to create the all parts of this mechanism and then assemble this.     Creation of First part: Create the required sketch according to the given dimension.                 

Objective: The main objective of this challenge is to understand the given master section to create a solid body and B-side features for a given class A surface, by considering all the design parameters. Master Section: Master sections are the guides for design requirements which decide the component packaging…

Dog house design for the Door Trim:   Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis. Objective: Create the Tooling axis  Design the class-B and class-C surfaces and…

AIM Create the component through the given Class-A surface.  the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create the rib and screw boss as by considering the design rules   CLASS A…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface.CLASS-B SURFACE: a surface below a certain thickness from the class-A…

COIN HOLDER To create a coin holder plastic component by closed method with reference to the class A surface and do the draft analysis for the component. Steps followed The class A surface is checked for the connectivity of the surface and ensure it is completely joined and there will be no gap between the surfaces. If…

Aim: Create the Switch Bezel Plastic component through the given Class-A surface. - Objectives: - To create class B & C surface for the given component. - To form the tooling axis and capture the surface properly. - To check the feasibility of the component with a draft of 3 degrees. - Method: - In order…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.   INPUT CLASS-A SURFACE:  SOLID PART BODY:…

Aim :- To design a Hood outer panel, inner panel and the necessary reinforcements by the given Master section and design parameters. Theory :-  Hood is a main component of front portion of a car. It is an opening body panel that covers the engine in front engine vehicle. It consist of an outer panel and…

Design of Back door    Aim:- To Design back door of car using 'A' class surface.   Introduction:- The back door is a hinged door/tailgate at the rear of the vehicle. It may be used for loading and unloading cargo, or to get passengers in and out, in case there are seats present at the rear. The back…

ROOF DESIGN AIM: To design a roof with all the components like front roof rail, rear roof rail, and bow roofs by following the given master sections and the high-quality surface, considering all the design requirements as per the OEM standards. ROOF  An automobile roof or car top is the portion of an automobile…

                                                                 Fender Design With mounts Aim:- The main aim is to design the fender model with the necessary…

Wheel Arc Gap AIM  To calculate the wheel arch gap at required points and check whether the car passes the European standard. Study about the different wheel arch gap standards. Draw the lines at the required angle and points for the European standard. Measure the distance at each angles and mention given model is…

Section modulus of hood Aim:- To find the section modulus of hood and optimization to improve overall section modulus.   Section modulus is a geometric property for a given cross section used in the design of beam or flexural members.other geometric properties used in design include area for tension and shear,radius of…

    HOOD DESIGN The hood or bonnet is a hinged cover over the engine of motor vehicles that allows access to the engine compartment, or trunk for maintenance and repair. The inner panel provides strength while the outer panel functions as the metal cover. Hood comes from the Old English word hod which means a…

                                                                              UNDER BODY COATING   Underbody parts…

REQURIMENTS: Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, a five-year-old boy, his father, and his mother. He visits his native place…

DESIGNING OF AMERICAN CHOPPER   AIM & OB JECTIVE To sketch and design american chopper different parts and assemble to form complete chopper in suitable environment   the in solidworks. To create a photorealistic rendering of the chopper using photoview360 and solidwork work visualize. INTRODUCTIOIN…