Challenge

Planetary Gear

AIM: -

Motion Analysis of Planetary gear in different condition

INTRODUCTION: -

In this Challenge, I have done Motion analysis of planetary gear mechanism which is consist of 4 planet gear in different torque input and output condition in solid works and concluded different plots for these conditions

THEORY: -

Planetary gear which is also called epicyclic gear train is an assembly of gears revolving around each other and transmits power (torque). these gears can be spur gear or helix gear. there are three main parts in this assembly (1). SUN GEAR (2). PLANETARY GEARS (3). RING GEAR (4). CARRIER

1.SUN GEAR

Sun gear is the main gear located at the middle of the gear train in most cases it is the power input source in gear train all planetary gear and ring gear revolved around the axis of the sun gear

2.PLANETARY GEARS

Planetary gear or gears can be one or more than one as per the requirement. they Revolve around the Sun gear. They all are connected with each other by means of a carrier. This gears mainly takes power from sun gear or transfers power to a sun gear

3.RING GEAR

Ring gear is the biggest member of this mechanism which consists of a planetary gear and sun gear. Ring gear is a kind of internal gear. It is in direct contact with planetary gears. It also provides support to planetary gears and sun gear as well as it also gives casing to all these gears.

4.CARRIER

Carrier is a supporting part for planetary gears which gives them support and at time of motion transmission it helps to keep planetary gears in position

In planetary gear mechanism, all gears have the same module for power transmission and there is one term called pressure angle which is an angle between a line tangent to face of tooth and a line tangent to pitch circle diameter of both gears.

STUDY SETUP: -

As per the given data Module and number of teeth of the sun gear and ring gear was given from that I have derived no. of teeth for planetary gears and Pitch circle diameter of all gears using the following equation

Planet gear teeth calculation

ZR = 2 * ZP + ZS

ZR = No. of teeth in ring gear

ZS = No. of teeth in sun gear

ZP = No. of teeth in planet gear

Module (m) = 2.5

No. of teeth of sun gear (Zs) = 14

No. of teeth of Ring gear (ZR) = 46

Now putting data in the equation

46 = 2 * ZP + 14

ZP = 16

Pitch Circle Diameter

Sun gear

DS = M * ZS

DS = 2.5 * 14

DS = 35 mm

Planetary gear

DP = M * ZS

DP = 2.5 * 16

DP = 40 mm

Ring gear

DR = M * ZS

DR = 2.5 * 46

DR = 115 mm

No. of Planetary gear used is 4

Gears are modeled in ANSI metric system with MMGS

Now we have all the required data as shown in below table

SUN GEAR

PLANETARY GEARS

RING GEAR

No. of teeth

14

16

46

Pitch Circle Diameter (mm)

35

40

115

Module

2.5

Pressure angle

20

Thickness (mm)

12

As per the data, I have modeled all the parts for planetary gear mechanism in solid works shown in below images

SUN GEAR

RING GEAR

PLANETARY GEARS

CARRIER

Then Assembly was done as shown in below images for assembly constraints are given in such a way that all gears are coincident to the right plane of assembly workspace

Then I gave concentric mate as well as coincident mate to all 4 planetary gears and carrier so that their places can be secured as shown in below image

Here is the whole assembly in which planetary gear, as well as carrier and ring gear, is revolving around a sun gear

RESULT AND EXPLANATION: -

Case 1

In case 1 Ring Gear was settled as fix component so only movement can be done by sun gear and carrier through planetary gear 200 RPM was given to Sungear and Graph of Angular velocity of Carrier was taken from it

Here is the graph of the angular velocity of Carrier in the excel sheet

Case 2

In Case 2 Sun Gear was settled as fix part so that ring gear and carrier can be movable then again motor (Torque) of 200 RPM was given to Ring gear and Graph of the angular velocity of the carrier was taken from it

Here is the graph of angular velocity of Carrier in excel sheet

CASE 3

In case 3 carrier was fixed by means of that ring gear and sun gear can be movable so here motion transfer was done by sun gear to planet gears to ring gear in this case planetary gears can rotate on their individual axis but they can’t rotate around an axis of a sun gear

Here again, motor (Torque) of 200 RPM was given to sun gear Graph of the angular velocity of ring gear was taken from it

Here is the graph of the angular velocity of Ring gear in excel sheet

Solidworks parts and assembly of this gear mechanism is attached herewith as well as excel graph and videos of motion transmission in every case are also attached

Your portfolio, next

Ship work like this
in your own course.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.