Challenge

MBD Simulation on IC Engine Valve Train

AIM: -

To perform a motion analysis of IC engine valve train

Introduction: -

In this challenge I have performed a motion analysis of IC engine valve train in solid works and also concluded contact forces between different parts like 1. cam and push rod 2.push rod and rocker arm 3.rocker arm and valve with respect to two different cams with 3.5 mm and 6 mm cam lift respectively

Theory: -

IC engine valve train is the most important part of any internal combustion engine, In an internal combustion engine, there is a term called VALVE TIMING DIAGRAM which is responsible for the smooth running of engine it simulates the time for every single process in I.C. engine with help of camshaft.

valve train consists of different parts which take energy from crankshaft and transfers to the valve on the top of the cylinder

1.Cam

Cam or camshaft is a rotating element of valve train which takes rotation energy from the crankshaft by means of gears. speed ratio of gears depends on the no. of stroke per cycle in the engine for 4 stroke engine speed of camshaft will half of crankshaft and for 2 stroke engine speed of camshaft will be same as the speed of the crankshaft

Design of cam is important criteria as Opening length depends on the cam lift and time for opening and closing of the valve depends on rise, fall & dwell period of cam

2.Pushrod

The pushrod is a motion converting element which converts the rotary motion of cam into linear motion and also gives height to transfer motion to the valve on top of the cylinder

3.Rocker arm

Rocker arm is just a motion transmitting element here but it also changes the direction of motion upward to downward as it has a pivot axis

4.Valve

The valve is our main part of interest in the valve train, it simulates the inlet and outlet of fresh charge and exhaust gases respectively it is located in the cylinder head and it has spring connection with valve stem

-valve stem

The valve stem is fixed part in cylinder head which gives support to spring as well as help to position the valve in cylinder head

Motion study setup: -

1.Cam

2.Pushrod

3.Rocker arm

4.Valve

5.Valve stem

For motion study assembly has been done as shown in image and material for all parts are given as CAST CARBON STEEL

Constraints are given in such a way that all parts move in the required direction and by using physical move option assembly is now ready for motion study

In motion study option

  1. Motor (Torque) of 1500 rpm was given to the center axis of the cam.
  2. Contact was given between cam and push rod and material was chosen as steel (dry).
  3. Contact was given between push rod and rocker arm and material was chosen as steel (dry).
  4. Contact was given between rocker arm and valve and material were chosen as steel (dry).
  5. Spring was given between valve head and valve stem with 20 N/mm stiffness And the length was given as 45 mm

-Then time was taken as 0.2 second and all the calculation are done in 9000 frames per second and with precise contact

Result and Explanation: -

CASE 1. – 3.5 mm cam lift

Graph of linear displacement of valve is shown below: -

The graph in excel sheet is also shown below

The contact force between the surface of cam and pushrod is shown in below graph:-

The same graph is also given in excel sheet where maximum force noted is 2999 N in magnitude

The contact force between the pushrod and rocker arm is shown in the below graph:-

The same graph is also done in an excel sheet and here maximum force is noted as 3116 N in magnitude

The contact force between the rocker arm and valve in magnitude is shown in the below graph: -

the graph is also done in an excel sheet and here maximum force is noted as 743 N in magnitude

The contact force between the rocker arm and valve in the X direction is shown in the below graph: -

the graph is also done in excel sheet and here maximum force is noted as 84 N and minimum force is noted as -181 N in the X direction

In below graph comparison between contact force in magnitude and X direction is shown

CASE 2. – 6 mm cam lift

Graph of linear displacement of valve is shown below: -

Graph in the excel sheet is also shown below

The contact force between the surface of cam and pushrod is shown in below graph:-

The same graph is also given in excel sheet where maximum force noted is 2325 N in magnitude

The contact force between the pushrod and rocker arm is shown in below graph:-

graph is also done in excel sheet and here maximum force is noted as 1638 N in magnitude

The contact force between the rocker arm and valve in magnitude is shown in the below graph: -

graph is also done in an excel sheet and here maximum force is noted as 494 N in magnitude

The contact force between the rocker arm and valve in the X direction is shown in the below graph: -

graph is also done in excel sheet and here maximum force is noted as 126 N and minimum force is noted as -120 N in the X direction

In below graph comparison between contact force in magnitude and X direction is shown

Conclusion: -

Linear displacement of the valve

(Approx.)

Contact force between

Cam and push rod in magnitude

Pushrod and rocker arm in magnitude

Rocker arm and valve in magnitude

Rocker arm and valve in the X direction

3.5 mm cam lift

4 mm

2999 N

3116 N

746 N

+84 & -181 N

6 mm cam lift

7 mm

2325 N

1638 N

494 N

+126 & -120 N

Here linear displacement is a little bit bigger than cam lift it is due to the shape of the rocker arm

Also here is difference between contact force in magnitude and in the X direction, because In x-direction it shows only normal forces in x-direction when in magnitude it shows force vector of normal force and friction force in directions

- All part files and assembly file of Solidworks is attached herewith as well as all the graph and data in excel is also attached

Your portfolio, next

Ship work like this
in your own course.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.