Challenge

MBD Simulation on a Piston Assembly

Aim:-

Motion Analysis on Piston - Crank assembly

Introduction:-

In this Project, motion study has been done on Piston crank assembly in solid works in different conditions of position for gudgeon pin in the piston head

Theory:-

Piston crank assembly is the main part of any engine where power generates and converted into the rotary motion for Movement of a machine or further usage

This assembly consists of parts 1). Piston head 2). Connecting road 3). Gudgeon pin 4). Crankshaft

1.PISTON HEAD

The piston head is work as an isolator in the cylinder where combustion takes place and in power stroke the only movable component is piston head so energy produced in power stroke pushes the piston head downward and converts that energy into rotary motion by means of gudgeon pin and connecting rod to the crankshaft

- Piston ring

There are three piston rings located on the surface of piston out of these three rings two rings are compression ring and one ring is oil scrap ring

1.Compression ring

Compression rings are essential for maintaining contact between the piston head and cylinder and sealing the combustion chamber as well

2.Oil scrap ring

Oil scrap ring is used to scrap the lubrication oil from cylinder inner surface because if lubrication oil mixes with fresh charge then there can be uneven combustion which can result in lower efficiency of the engine

2.Gudgeon pin

Gudgeon pin is used for connecting the piston head with the connecting rod. It is kind of cylindrical pin whom both ends are connected with piston head and smaller section of the connecting rod is connected in the middle of the gudgeon pin

3.Connecting rod

The connecting rod is a motion as well as an energy transmitting element between the piston head and crankshaft. Its smaller end is connected with piston head by the help of gudgeon pin and the bigger end is connected with the crankshaft with help of Endcap

- Endcap

The end cap is used to connect the connecting rod with the crankshaft it is bolted with the bigger end of connecting rod

4.Crankshaft

The crankshaft is a motion converting element that converts translating motion into rotary movement. It is consisting of series of crankpin and cranks main output of the engine is a rotation of crankshaft from that we get useful rotary motion to rotate any wheel so gear, for speed variation we use gearbox attached with it crack shaft also gives motion to valve mechanism of the engine by means of gear transmission

Study setup: -

Setup is consisting of all the parts explained above, dimension position of elements of this parts are shown in figure

1.Piston head

Then on the surface of the piston, there is a slot given for three piston rings

for a first case, we have located gudgeon pin in the center of the piston

Then created a cut in the lower portion of piston to ensure that connecting road can’t strike with the inner surface of the piston

  1. Connecting rod

3.Crankshaft

4.Endcap

5.Gudgeon pin

Assembly of this all parts shown in below images for specific movements constraints are given in such a way that they move in desired direction piston head can only move up and down in its position and crankshaft only can rotate about its axis no translation movement allowed in any direction

For motion study, there is three conditions of position for gudgeon pin in the piston is given

  1. 0 mm offset

2. 10 mm positive offset from the center

3. 10 mm negative offset from the center

For motion study 2000 RPM motor(torque) was given to axis of the crank in clockwise direction and gravity was also defined in downward ( Z ) direction and contact between all the parts were defined as steel (dry) material

Results and explanation: -

For a better understanding of movement at every point, motion study was done in 12000 frames per sec for the time of 0.2 sec

For every case graph of linear displacement of piston head are shown below

  1. 0 mm offset

For the first case distance to the topmost position of the piston head is archived as 324 mm and lower position is noted 225 mm from the center of crankshaft graph in excel sheet is shown below

2. 10 mm positive offset

For 10 mm positive offset distance to the topmost position of the piston head is archived as 307 mm and the bottom position is at 207 mm from the center of crankshaft also graph In excel sheet is shown below


3.10 mm negative offset

For 10 mm negative offset distance to the topmost position of the piston head is archived as 307 mm and the bottom position is at 207 mm from the center of crankshaft also graph In excel sheet is shown below

In the below graph, all the conditions are shown in the graph

Here we can see that with offset we can get a smaller size of the engine in terms of vertical length along with the movement of the piston

In a comparison of 10 mm positive and 10 mm negative there is no change in the top and bottom position of piston head but piston with 10 mm negative offset start moving a little bit earlier than 10 mm positive offset from same initial start position rather than that there is no change in cycle time also

  • Solidworks files of part and assembly piston crank mechanism as well as graph and data for different conditions in excel are attached herewith
Your portfolio, next

Ship work like this
in your own course.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.