Challenge

Internal Geneva Mechanism

AIM: -

To perform a motion analysis of internal Geneva mechanism

Introduction: -

In this challenge, I have performed a motion analysis of internal Geneva mechanism in solid works and also compared the different result of different specified data like, with precise contact and without precise contact and also derived data for the angular velocity of driving member (wheel) and angular displacement of driven member(wheel)

Theory: -

Geneva mechanism is basically coverts continuous rotary motion into intermittent motion of driven wheel it was founded by a watchmaker from swiss, at that time function of this mechanism was to prevent from over-winding of watch spring that’s why it is also called as Geneva stop

There are two main members involved in this mechanism

(1) Driving wheel,

(2) Driven wheel

Driving member or wheel is directly coupled with motor or gearbox which drives the driving wheel. It also has a pin on the surface of it which comes in contact with a groove of the driven wheel.

The driven member has a groove in its body. Motion is transferred through contact between the pin of driving member and groove on driven member. And its constant continuous rotary motion gets converted into discrete motion

Grooves or slots of the driven member is decided on the bases of the angle which we required to rotate our driven member in this setup I have used 4 grooves which will rotate the driven member to the angle of 90 degrees after one revolution of driving wheel

This mechanism has two version

1.External version

2.Internal version

External version is smaller in size then internal version and dwells time for the driven wheel is higher in the external version then internal version and in terms of withstanding stresses external drive is more useful

Motion study setup: -

For this motion study, I have designed this internal Geneva mechanism in solid works with dimension showed in below images

Driving wheel

Driven wheel

This is the assembly of internal Geneva mechanism

for this first I have added both members in assembly file then I started giving mate to both of them

For constraining driving member on the front plane I have constrained front plane of driving member with the front plane of assembly workspace by using coincident mate after that I have fixed Z-axis of assembly workspace as an axis of rotation for driving member by constraining the original axis of driving wheel with the top plane and the right plane of assembly workspace by using coincident mate one by one for both respectively by doing this my driving wheel was constrained to rotate about the z-axis of assembly workspace and it was coincident to the front plane of assembly workspace.

After that, I constrained driven member by giving distance coincident mate between the front plane of driven member and front plane of assembly workspace by a distance of 20 mm which is a thickness of driving wheel so bottom surface of driven member and the upper surface of driving member get coincident by using this approach after that I have constrained axis of the driven member with the right plane of assembly workspace for fixing its axis on that plane but still, it was under defined so I have constrained it by giving the center distance between both the axis of driven member and driving member respectively distance between them was 266.27 mm

For finding this distance I went to sketch of the driven member then drawn a 3 point circle of 320mm diameter tangent to center line 2 consecutive grooves as shown in below image because the distance between the center of driving wheel and center of the pin on the driving wheel was 160 mm so the perimeter of this 320 mm circle is taken as a path of pin

Now, both the members are fully defined and can be used for further motion analysis

Result and Explanation: -

In Motion workspace, I have given motor to the driving wheel as a 10 rpm first and defined solid contact between the driving wheel and driven wheel in a motion analysis environment

At first, it was set to 25 fps and without precise contact from this result has given below with comparison with excel sheet graph

Contact force (between driving and the driven wheel) as a function of time.

Angular Displacement of the driven wheel.

After that, I have set it to 60 fps and without precise contact at 10 rpm, the result is shown below

Without precise 60fps 10 rpm

After that, I changed the setting to “Use Precise Contact” and after calculating again result has shown below with excel chart

After this, I edited motor function and changed rpm to 20 rpm and then I changed settings to 120 fps and without precise contact and again calculated this result shown below

Without precise 120 fps

Then again I changed setting to 120 fps and with enabling “Use Precise Contact” and again calculated result shown below

With precise

And then I also found a graph for the angular velocity of driving wheel result shown below

Angular velocity of driving wheel

Conclusion: -

In motion simulation for contact, forces result in there is a difference between 60 fps with 10 rpm and 120 fps with 20 rpm due to change in FPS higher the fps exact will result in 60 fps max. the reaction force is 7332 newton and in 120 fps max. the reaction force is 6520 newtons

As well as we also found a difference in result with “Use Precise Contact” disabled and enabled because if we enable this option that motion is used to be precise and according to guidelines of solid works the result with this option enabled is considered as an analytically correct result

CONTACT FORCE RESULT

60 FPS & 10 RPM

120 FPS & 20 RPM

WITHOUT PRECISE CONTACT

7332 N

6520 N

WITH PRECISE CONTACT

6340 N

6020 N

Your portfolio, next

Ship work like this
in your own course.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.