Drafting of various geometries using Chamfer, Fillet tool in AutoCad

Given: Column size = 400x400mm SBC = 150 kN/mm2">mm2 Compression axial load = 2000 kN fck">fck = M25 Steps to design a square footing: 1) Size of Footing 2) Net upward Pressure 3) Bending moment 4) Depth of Footing 5) Reinforcement 6) One way and Two-way shear Step 1: Size of Footing:  Load on column…

  Aim: To model and analyze the G+7 storey building using ETABS with application of proper load cases and load combinations for the given typical floor plan drawing. Step 1: Open the ETABS Software. Set the Grid and storey details using editing options.Provide 4 grids at x-Direction and 6 grid at y-Direction with…

AIM: This challenge aims to run the analysis and design of the RCC shear walls. And to extract the values of the longitudinal steel ratio, boundary element length and the shear reinforcement ratio from the design results. PROCEDURE: So first of all open the ETABS file which is given in the question itself. Open that file…

  Aim:   To analyse the given ETABS model and to extract the design results and detailing of two mentioned RC columns. Also the calculation for special confining reinforcement has to be ensured based on clause 8.1 of IS 13920-2016.   Design of RC columns:     Step-1:   Analyse > Check model   Analyse > Run analysis    …

  Aim To design the beams in detail, form the Etabs 2017 To provide the detailing of longitudinal and shear reinforcement for two continuous beams. To provide the reasons of failure at middle span along grid A.   Introduction   Beams are horizontal structural elements used for the supporting lateral loads.…

  AIM : Comparative study of different storey buildings for Seismic forces INTRODUCTION : There are 10 project of different story building (A, B, C, D, E, F, G, H, J, K).   Material Properties assigned as : Grade of Concrete : M30  Grade of Steel Reinforcement Bars : Fe 415    Loading : Dead…

  Challenge 6 – ETABS modelling of a 25 storey building Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres.  Structural…

Question 1 :  The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the…

Question 1. Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. To describe the symmetry, redundancy, bi-directional stiffness, and…

Understanding the concepts on Degrees of Freedom   Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures. Ans.- AIM-:  Differentiate Static analysis and Dynamic analysis  Static Analysis Dynamic Analysis  static analysis time invariant analysis of forces like Stress, strain and displacement etc. Dynamic analysis is time…

a)                                         OBSERVATIONS: In this picture we observe that concrete gets damaged/broken and reinforcement is visible at the bottom of the beam. The concrete spoiled beyond the reinforcement…

AIM:   To Create a 3D Isometric View RESIDENTIAL of the building with plan given.   INTRODUCTION: Isometric drawing is a method of presenting the designs in three dimensional form.  In order for a design to appear threee dimensional, a 30 degree angle is applied to its sides.   Isometric drawings…

CREATING 3D ISOMETRIC VIEW OF VARIOUS STRUCTURAL ELEMENTS   Introduction Isometric drawings: These drawings are not actual 3D drawings, they are made with 2D geometries but they appear like 3D. Isometric drawing in AutoCAD can be made by tilting viewing angle to 30 degrees for all of its sides in the 2D plane. Isometric…

Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing Aim:  To create a 3D Furniture element using AutoCAD software. Introduction: Various commands used: QNEW command UN command Box command Rectangle command Extrude command SUBTRCT command DIMLIN command 3DO command UCS command Procedure:…

1.Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing Aim:  To create a 3D Furniture element using AutoCAD software. Introduction: Various commands used: QNEW command UN command Box command Rectangle command Extrude command SUBTRCT command DIMLIN command 3DO command UCS command…

AIM: To create layout of plan and section, creating viewports, editing attributes and taking a plot. To create a kitchen layout in A4 sheet and take a plot To create Multiview ports for industrial section drawing, scaling it and taking a plot. COMMANDS USED: View Layout. Multiple View. Model Space. Paper Space. Scale.…

Q1. Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards.     Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques…

Aim - Creating Bar Bending Schedule, Different Door types, and Creation of Standard drawing templates using AutoCadCreating Bar Bending Schedule, Different Door types, and Creation of Standard drawing templates using AutoCad Introduction 1.…

 Design and Draft a layout of a residential building with the following details: Plot Size: 60’x20’(18.3m x6m)  Orientation- Facing East  Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections) 2. Structural Drawing (Column, Bean, Footing Plan)   Aim: To…

CHALLENGE 7-1. Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project. Assume the sizes of the doors and windows as per construction standards. Refer to sections for stair details if required. AIM- TO DRAW PLAN ELEVATION AND SECTION OF THE HOUSE…

Aim: To draw the cabinet, floor plan, kitchen, column details and raft layout drawing: Procedure: commands used in AutoCad are as follows: Line- to draw horizontal and vertical line of known distance we use the line command with command"L" by selecting the start point and end point. Rectangle- to draw the rectangle we…

1. COLUMN SCHEDULE: Aim: To prepare column schedule. Procedure: First we create a table by drawing a rectangle of 60'X20' and then explode it. By using offset command: offset the 20' line by taking offset at a distance of 5' and then offset the 60' line at a distance of 4' from bottom and 2' from top. Trim off the…

Aim: This challenge aims to show the application of the AutoCAD software in the Civil Engineering industry. In this challenge, the AutoCAD software is applied in the sketching of a Residence Layout, Seating Plan, and Toilet Rooms. With the combination of the different AutoCAD tools, the sketch can be provided easier…

Drafting of various geometries using Chamfer, Fillet tool in AutoCad AIM: To draw the geometries using Chamfer, fillet tool in Auto cad. Commands used: Line. Circle, chamfer, fillet, mirror, trim, move. Procedure: New sheet- units- decimal-precision 0.00- meter-ok. Limits- 0,0 and 420,210. zoom-All. Select Line tool and…

AIM :   To create the given footing plan, footing detail and isometric view using AutoCAD. Introduction: The main objective of this assignment is to get in touch with various tools in Auto Cad like rectangle, polylines, modification tools like copy, move etc. These tools will be understood by creating footing detail, two-bedroom…

AIM: To Create the geometric from P1 to P2 using all the coordinate system methods. Apparatus: Autocad software Coordinate systems: Absolute coordinate Relative coordinate Relative polar coordinate Direct distance entry Procedure: Open autocad QNEW command As decimal units are used (metric is selected) Template = Acad.dwg…

Aim: To calculate the Concrete Mix Design for M35 grade concrete with fly ash and        M50 grade concrete without fly ash. INTRODUCTION:        Concrete mix design is the method of finding the precise proportion of cement, sand and aggregates for concrete…

AIM: To prepare a residential plan for G+1 floor according to Vaastu shastra and to calculate corresponding loads for components of house. INTRODUCTION TO VAASTU SHASTRA :- Vaastu Shastra is the Ancient Indian Science of architecture and acts as a guideline to design your home in the way that enhances positive energy.…