Creation of geometries by Coordinate system methods using AutoCad

Q-1

A)P-1

Aim :-

To draw the given drawing using AutoCAD by absolute coordinate method

Procedure :-

1. Set all limits as per given drawing
2. Take line command and set origin point at (2,1)
3. And draw the second point (6.0)and continue with (0,1)(-5,0)(4,0)(0,5).....
4. Joint all the lines correctly and then measure dimension and check with drawing

P-2

Aim:-

to draw the given drawing using AutoCAD by absolute co-ordinate method

Procedure:-

1. Set all the limits as per given drawing
2. Take line command and set origin point as per (2,1)
3. And draw the second point (3,0) and continue with (0,4)(1,0)(0,-4)(0,7).......
4. joint all the line correctly and then measure dimension and check with drawing

P-3

Aim:-

to draw the given drawing you will AutoCAD by absolute coordinate method.

Procedure:-

1. Set all the limits as per given drawing
2. Take a line command and set origin point as (2,1)
3. Andrew the second point (3,0) and continue with (0,4)(1,0)(0,-4)(0,7).....
4. joint all corthe lines and then measure diamenion and check with drawing

P-4

Aim:-

To draw the given drawing using AutoCAD by absolute coordinate method

Procedure :-

1. Set all the limits as per given drawing
2. Take line command and set origin point as (2,1)
3. And draw the second point (8,0) and continue with (7,0)(1,0)(0,-6)(-4,0)....
4. Joint all the line correctly and then measure diamention and check with drawing

P-5

Aim:-

To draw the given drawing using autocad by relative rectangular coordinate method

Procedure :-

1. Set all the limits as per given drawing
2. Take line command and set origin point as (@2,1)
3. And draw the second point (@8,0) and continue with (@0,4)(@1,0)(@0,-10)(@0,6)....
4. Joint all the line correctly and then measure diamention and check with drawing

P-6

Aim:-

To draw the given drawing using autocad by relative rectangular coordinate method

Procedure :-

1. Set all the limits as per given drawing
2. Take line command and set origin point as (@0,0)
3. And draw the second point (@10,0) and continue with (@0,4)(@1,0)(@0,-10)(@0,2)....
4. Joint all the line correctly and then measure diamention and check with drawing

P-7

Aim:-

To draw the given drawing using autocad by absolute coordinate method

Procedure :-

1. Set all the limits as per given drawing
2. Take line command and set origin point as (1,1)
3. And draw the second point (5,0) and continue with (0,2)(0,-3)(0,3)(4,0)....
4. Joint all the line correctly and then measure diamention and check with drawing

P-8

Aim:-

To draw the given drawing using autocad by absolute coordinate method

Procedure :-

1. Set all the limits as per given drawing
2. Take line command and set origin point as (1,1)
3. And draw the second point (2,0) and continue with (0,3)(0,7)(0,-1)(3,0)....
4. Joint all the line correctly and then measure diamention and check with drawing

P-9

Aim:-

To draw the given drawing using autocad by absolute coordinate method

Procedure :-

1. set all the limits as per given drawing
2. Take line command and set origin point as (0,0)
3. And draw the second point (10,0) and continue with (1,0)(0,4)(2,0)(0,1)....
4. Joint all the line correctly and then measure diamention and check with drawing

P-10

Aim:-

To draw the given drawing using autocad by absolute coordinate method

Procedure :-

1. set all the limits as per given drawing
2. Take line command and set origin point as (1,1)
3. And draw the second point (10,0) and continue with (4,0)(0,1)(2.53,0)(0,-1)....
4. Joint all the line correctly and then measure diamention and check with drawing

P-11

Aim:-

To draw the given drawing using autocad by absolute coordinate method

Procedure :-

1. set all the limits as per given drawing
2. Take line command and set origin point as (1,1)
3. And draw the second point (6,0) and continue with (2,0)(0,2)(2,0)(0,-2)....
4. Joint all the line correctly and then measure diamention and check with drawing

P-12

Aim:-

To draw the given drawing using autocad by relative rectangular coordinate method

Procedure :-

1. set all the limits as per given drawing
2. Take line command and set origin point as (0,0)
3. And draw the second point (1,0) and continue with (2,0)(3,0)(4,0)(5,0)....
4. Joint all the line correctly and then measure diamention and check with drawing