Creating Architectural and Structural model with 3D rendering using REVIT

1)

AIM: TO SELECT THE STRUCTURE OF YOUR CHOICE FOR THE PROJECT , THE STRUCTURE SELECTED IS AN OFFICE BUILDING WHICH PROVIDES THE IT SERVICES .

ITS A 3 STOREY BUILDING WHICH IS SHAPED IN A TRIANGULAR MANNER.

2)

AIM: TO DETERMINE THE REASONABLE ASSUMPTIONS FOR GEOGRAPHIC AND LOCATION DETAILS OF YOUR PROJECT MODELLING, BASED ON ASSUMPTIONS AND TYPE OF STRUCTURE SELECTED IDENTIFY THE MODELLING REQUIREMENTS FROM NBC

STEPS THAT UDCPR SUGGEST:

• THE OPEN SPACE AROUND THE BUILDING SHALL NOT LESS THAN 4.5 M
• THE TYPE OF CONSTRUCTION AS TYPE 2 CONSTRUCTION , THE FAR VALUE FOR THE BUSINESS BUILDING SHALL BE TAKEN AS 2.9 AS PER UDCPR.
• THE PLOT SIZE IS TAKEN AS 40M X 70M. I.E 2800 M^2 AND INDIVIDUAL FLOOR AREA IS 2000 M^2. HENCE FAR VALUE OBTAINED IS 2.14 WHICH IS WITHIN THE PRESCRIBED LIMITS AS PER NBC .
• THE WIDTH OF THE ROAD ABUTTING THE BUILDING IS TAKEN AS 6 M (20')

3)

AIM : TO DETERMINE THE STRUCTURAL UNITS FOR THE STRUCTURE WHICH IS AS FOLLOWS

STEPS :

• FOOTINGS - THE FOOTINGS SELECTED ARE ISOLATED FOOTINGS BENEATH THE COLUMN , THE WALL FOOTINGS ARE ALSO SELECTED FOR THE STRUCTURES.
• COLUMNS - THE COLUMNS USED FOR THE STRUCTURE ARE CIRCULAR COLUMN OF 500MM DIA WHICH ARE PLACED ALONG THE PERIPHERY OF THE STRUCTURE.
• BEAMS - THE PRIMARY BEAMS ARE SELECTED SO AS THE LOAD DISTRIBUTION IS IN A UNIFORM PATTERN .
• JOIST - THE SUPPORTING JOISTS ARE PLACED WITHIN THE PRIMARY BEAM SO AS TO SUPPORT THE SLAB IN THE STRUCTURE .
• SLAB - THE THICKNESS OF THE SLAB IS 125 MM USED AND IT IS MOSTLY TWO WAY AS ALONG THE PERIPHERY THE SUPPORT IS PRESENTED IN THE SLAB .

4)

AIM: USING THE ARCHITECTURAL MODEL THE FOLLOWING COMPONENTS BASED ON STRUCTURE IS SELECTED.

• WALL LAYOUT WITH APPROPRIATE MATERIAL AND FINISHING: THE WALL SELECTED AT THE EXTERIOR OF THE STRUCTURE IS A CURTAIN WALL ALONG THE PERIPHERY OF THE STRUCTURE. THE PARTITIONS WALLS ARE ALSO SELECTED IN THE FLOOR SO THE DIFFERENT OFFICE SPACES ARE CREATED AT EACH LEVEL
• EXTERIOR FACADE : AS THE CURTAIN WALL ARE SELECTED ALONG THE PERIPHERY IT GIVES THE AESTHETIC VIEW TO THE BUILDING AS THE MULLIONS ARE ALSO CREATED .
• INTERIOR PARTITION : INTERIOR PARTITION WALLS ARE PROVIDED TO SEPERATE THE OFFICE SPACES IN THE STRUCTURE .
• COMPONENTS TO ADD DETAILS TO A ROOM : AS THE STRUCTURE IS AN OFFICE BUILDING THE FURNITURE ITEMS MOSTLY ARE TABLES & OFFICE CHAIRS .
• INTERIAOR AND EXTERIOR LIGHT PLACEMENTS ARE ALSO PLACED IN THE STRUCTURE TO LIT UP THE STRUCTURE DURING THE NIGHT TIME .
• TOPOGRAPHIC COMPONENTS ARE ALSO PLACED ALONG THE STRUCTURE AITE IT MAINLY INCLUDES THE TREES AND SHRUBS AND PARKING SITES IN THE MODEL.

5)

AIM: TO PROVIDE A SET OF DRAWINGS IN AN ARCHITECTURAL AND STRUCTURAL MODEL TO LIST THE FOLLOWING DETAILS AND CATEGORIES AND APPROPRIATE SHEETS INCLUDED THE SHEETS ARE ATTACHED IN THE PROJECT

• FLOOR PLANS WITH ANNOTATIONS: THE FLOOR PLAN OF ONE OF THE STOREY IS ATTACHED AS THE THE ABOVE TWO FLOOR HAS THE SAME UNITS
• ELEVATIONS: THE THREE SIDE ELEVATION OF THE STRUCTURE IS ADDED TO THE MODEL
• SECTIONS : SECTION LINE PASSING HORIZONTAL AND VERTICAL MANNER THROUGH THE MODEL IS PLACED AND THE RESPECTIVE DRAWING AS PER THE SECTIONAL LINE IS ALSO ATTACHED

6)

AIM: USING THE RENDERING SETTINGS , RENDER THE IMAGES OF THE 3D MODEL PRODUCED & INCLUDE THE RENDER IMAGES TO THE SHEETS .

THE RENDER IMAGES OF THE FOLLOWING ITEMS IS PASTED IN THE PROJECT WORK :

• RENDERING FROM INTERIOR ROOMS
• RENDERING FROM OUT SHOWING TOPOGRAPHIC FEATURES
• RENDERING THROUGH STRUCTURAL FRAMINGS

7)

AIM: TO PRINT THE SET OF DRAWING OF SHEETS CREATED AND SUBMIT THE DRAWINGS FROM ARCHITECTURE AND STRUCTURE MODEL.