Creating Architectural and Structural model with 3D rendering using REVIT

ANS 1 (AIM: SELECT THE TYPE OF STRUCTURE YOU WANT TO BUILD FROM ONE OF THE THREEE BELOW

a MULTI UNIT RESIDEN TIAL 

b OFFICE BUILDING 

c SCHOOL

ANS ) OFFICE BUILDING 

ANS 2 

AIM: ASSUME REASONABLE ASSUMBTION FOR GEOGRAPHIC AND LOCATION DETAILS FOR YOUR PROJECT MODELING . BASED ON ASSUMBTION AND TYPE OF STRUCTURE SELECTED IDENTIFY THE MODELING REQUIRMENTS FROM NBC .

PROCEDURE : My project is in plain area .

It is in commercial area .

Road width infront of my structure is 70ft 

MODELLING REQUIRMENTS FROM NCB ARE : 

An exit must be provided in every building sa as to permit safe escape of employes in case of earthquake or fire hazards .The minimum height of basement should be 2.5m and maxm height should be 4.5m 

ANS 3 

AIM: USING THE STRUCTURAL MODEL ,INCLUDED THE FOLLOWING COMPONENTS BASED ON THE TYPE OF STRUCTURE SELECTED 

a FOUNDATION -ISOLATED / WALL / MATT FOUNDATION 

B COLUMNS 

c BEAMS CONNECTED TO COLUMNS 

d ROOF FRAMING / TRUSS 

e FLOOR / DECKS 

f FLOOR OPENINGS FOR ELEVATOR AND STAIRS 

PROCEDURE : 

• Open revit and make horizontal and verticals grid at spacing of 30' as per ncb 
• Go to elevation and increase the number of levels upto roof and change their names 
• Select columns from ribbon and places the columns at intersction of grids as 
• Place another columns on the grid interesection from the ground floor to first floor 
• Now select beam from ribbon and connect this beam to dion fferent columns 
• Now go to isolated option from the ribbon and place them on the different column 
• Select the entire figure and go to the copy option and assign them to first floor and section floor 
• Now go to the wall option and select the floor you want to assign the wall copy it andassign to different level 
• Let make a roof to place stairs , go to the floor option and draw rectangle in the plan , change the view to 3d
• Draw a shaft and makes stairs in that and place it different floor level 

ANS 4 

AIM : USING THE ARCHITECTURAL MODEL , INCLUDED THE FOLLOWING COMPONENTS BASED ON THE TYPE OF STRUCTURE SELECTED 

1. Wall layout with apporopriate material and finishing 
2. Exterior facade with fancy finish 
3. Interior partition walls to size room 
4. Components to add details to a room 
5. Add components such as stairs elevator 
6. Have at least one side of the building with curtain walls and glass panels 
7. Included interior and exterior lightb fixtures 
8. Places proper topographic components from outside 

PROCEDURE : 

1. Initially , we have to link the architectural and structural template .
2. For this , first open architectural template and then insert the structural template into it .
3. for this , go to insert tab --> Revit link --> choose the link 
4. change the front wall of the building with curtain walls or glazed panel as copy the entire figure and place it first floor 
5. Draw the roof by making a rectangle along all the sides of second floor 
6. now go to the plan view and draw a rewctangular floor and view it in 3d 
7. Go to place a component and add the required component from the library and place it 

ANS 5 AIM :PROVIDE A SET OF DRAWING IN AN ARCHITECTURAL AND STRUCTURAL MODEL TO LIST THE FOLLOWING DETAILS WITH CATEGORIES AND APPOROPRIATE SHEETS TEMPLATE INCLUDED 

A ) FLOOR PLANS WITH ANNOTATION 

B) ELEVATION 

C) SECTION 

PROCEDURE : For to the sheets option , as the sheet opens there is another option below it called view and select the required view you want to place 

ANS 6 

AIM : USING THE RENDERING SETTINGS, RENDER IMAGES OF THE 3D MODEL PRODUCED AND INCLUDED THE RENDERED IMAGES TO DRAWING SHEET 

a Rendering from interior rooms 

B Rendering from out showing topographic features 

c Rendereing through structural framing 

PROCEDURE:

In order to render any figure go to render option from the ribbon and change the setting you want and click render will turn to realistic 

ANS 7 AIM : TO PRINT AND SET OF DRAWING SHEETS CREATED AND SUBMIT THE DRAWINGS FROM THE ARCHITECTURAL  AND STRUCTURAL MODEL