Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad
1. AIM:- To draw a residence plan of figure 1 with the use of AutoCAD 2022
PROCEDURE:-
- Click on AutoCAD application and open the application
- Type a command QNEW to save the file
- Type a command units.
- Select architectural type,0'-0 1/2" in precision,insertion scale units in inches,decimal type and precision in 0 for decimal.Click OK
- Type a command limmax
- Enter new value for limmax:- 100',100'
- Type a command zoom and select all
- Type a command limits
- Specify lower left corner:- 0,0
- Specify upper right corner:- 70',70'
- Type a command zoom and then select all
- Type a command XLINE
- Specify the line:- Vertical
- Specify through point:- Click it anywhere
- Type a command XLINE
- Specify the line:- Horizontal
- Specify through point:- Click it anywhere
- Type a command and then trim at corner edge
- Type a command:-Offset
- Specify offset distance:- 9"
- Type a command:- Offset
- Specify offset distance:- 43'6.5"
- Type a command offset
- Specify offset distance:- 9"
- Type a command offset
- Specify offset distance:- 25'
- Type a command trim and then trim the unwanted lines
- To draw a bed 1, type a command offset
- Specify offset distance:- 11'7.5"
- To draw an inner wall, type a command offset
- Specify offset distance:- 4.5"
- Type a command offset
- Specify offset distance:-12'
- Type a command trim and then trim the unwanted lines
- To draw a bed 2,type a command offset
- Specify offset distance:- 11'6"
- Type a command trim and trim the unwanted lines
- To draw a toilet 1, type a command offset
- Specify offset distance:-4.5" for interior wall
- Type a command offset
- Specify offset distance:-4'6"
- Type a command offset
- Specify offset distance:-4.5" for interior wall
- Type a command offset
- Specify offset distance:-8'3"
- Type a command offset
- Specify offset distance:-4.5"
- Type a command trim
- Trimmed the unwanted lines
- To draw a toilet 2, type a command offset
- Specify offset distance:-8'1.5"
- Type a command offset
- Specify offset distance:-4.5"
- Type a command trim
- Trim the unwanted lines
- To draw a kitchen, type a command offset
- Specify offset distance:-2'
- Type a command offset
- Specify offset distance:-6'8"
- Type a command offset
- Specify offset distance:-11'7.5"
- Type a command offset
- Specify offset distance:-9"
- Type a command offset
- Specify offset distance:-6'4"
- Type a command trim
- Trimmed the unwanted lines
- To draw a living room, type a command offset
- Specify offset distance:-11'
- Type a command offset
- Specify offset distance:-9"
- Type a command trim
- Trimmed the unwanted lines
- To draw a door section, type a command circle,offset and extend
- To draw a staircase, Specify offset distance for 1' for each step ( 9 steps)
- Select the mid point of the line and draw an inclined line at the end point of it
- Type a command D or dimension style manager
- Select text height of 2 1/2",Precision of 0'-0" and overall scale factor of 5 units
- Type a command mtext
- Specify text height of 10"
- Dimensions of the above geometry is done with the use of command Dimension Linear
- Type a command layer properties to group down geometry is done in distinct and seperate categories
RESULT:- The above residence plan is done with the use of commands such as Xline,offset,Circle etc on AutoCAD 2022
2. AIM:- Sketch the seating plan for an outdoor canopy of figure 2 with the use of AutoCAD 2022
PROCEDURE:-
- Click on AutoCAD application and open the application
- Type a command QNEW to save the file
- Type a command units.
- Select decimal type,0 in precision,insertion scale units in millimetres,decimal type and precision in 0 for decimal.Click OK
- limits command is used
- limmax command is also used
- Zoom command is also used
- Type a command circle
- Specify centre point of circle:-0,0
- Specify radius of circle:-452
- Type a command circle
- Specify centre point of circle:-0,0
- Specify radius of circle:-1398
- Type a command line
- Enter a line passing through the centre of the circle
- Type a command offset
- Specify offset distance:- 645 from the centre of the circle vertically
- Type a command offset
- Specify offset distance:- 225 from @-645,0 horizontally on both the sides
- Type a command rectangle
- Specify corner point:-@-645,0
- Specify length and width of the rectangle:-190,450
- Type a command fillet
- Select radius
- Specify fillet radius:-10
- Type a command fillet
- Specify fillet radius:-10
- Draw a semeicircle of radius 225 mm
- Type a command offset
- Specify offset distance:- 25 from @-1060,0
- Type a command offset
- Specify offset distance:- 75 from @ -1085,0
- Draw the end points of the line
- Type a command offset
- Specify offset distance:- 25 from @-835,0
- Type a command rectangle
- Specify length and width of the rectangle:-90,74
- Type a command trim
- Trimmed the unwanted lines
- Copying the selected object and move at remaining three corner of the sides of the circle
- Type a command rotate
- Rotate angle by 45 degree on remaining three corners
- Type a command D or dimension style manager
- Select text height of 2.5,Precision of 0 and overall scale factor of 25 units
- Dimensions of the above geometry is done with the use of command Dim Radius
RESULT:- The above seating plan is done with the use of commands such as 0ffset,Circle etc on AutoCAD 2022
3. AIM:- Sketch the plan for toilet and utilities room of figure 3 with the use of AutoCAD 2022
PROCEDURE:-
- Click on AutoCAD application and open the application
- Type a command QNEW to save the file
- Type a command units.
- Select decimal type,0 in precision,insertion scale units in millimetres,decimal type and precision in 0 for decimal.Click OK
- limits command is used
- limmax command is also used
- Zoom command is also used
- Type a command XLINE
- Specify the line:- Vertical
- Specify through point:- Click it anywhere
- Type a command XLINE
- Specify the line:- Horizontal
- Specify through point:- Click it anywhere
- Type a command offset
- Specify offset distance:-150
- Type a command offset
- Specify offset distance:-300
- Type a command offset
- Specify offset distance:-1900
- Type a command offset
- Specify offset distance:-150
- Type a command offset
- Specify offset distance:-2100
- Type a command offset
- Specify offset distance:-150
- Type a command offset
- Specify offset distance:-1700
- Type a command offset
- Specify offset distance:-300
- Type a command trim
- Trimmed the unwanted lines
- Type a command offset
- Specify offset distance:-150
- Type a command trim
- Trimmed the unwanted lines
- Type a command offset
- Specify offset distance:-150
- Type a command trim
- Trimmed the unwanted lines
- Type a command offset
- Specify offset distance:-631
- Type a command offset
- Specify offset distance:-25
- Type a command offset
- Specify offset distance:-50
- Type a command offset
- Specify offset distance:-702
- Joined the vertical line
- Type a command offset
- Specify offset distance:-150
- Type a command offset
- Specify offset distance:-402
- Type a command offset
- Specify offset distance:-150
- Type a command offset
- Specify offset distance:-150
- Type a command trim
- Trimmed the unwanted lines
- Type a command offset
- Specify offset distance:-201
- Type a command offset
- Specify offset distance:-351
- Type a command offset
- Specify offset distance:-150
- Type a command offset
- Specify offset distance:-402
- Type a command offset
- Specify offset distance:-150
- Type a command trim
- Trimmed the unwanted lines
- To draw a window, type a command window
- Specify offset distance:- 728
- To draw a ventilator type a command offset
- Specify offset distance:- 631
- To draw a door section, type a command circle,offset and extend
- To draw a toilet utilities, type a command circle,offset and extend and then trimmed it
- Type a command D or dimension style manager
- Select text height of 2.5,Precision of 0 and overall scale factor of 30 units
- Type a command mtext
- Specify text height of 7.5 units
- Dimensions of the above geometry is done with the use of command Dimension Linear
RESULT:- The above plan for toilet and utilities room is done with the use of commands such as 0ffset,Circle etc on AutoCAD 2022
