Analysis & Design of RCC shear walls in the model using ETABS

AIM: 1. To calculate and assume data from the given Architectural and site information    2. To model, Analysis and design the frame structure using Etabs Software  3. To model, Analysis and design the foundation using safe software 4. To produce a structural typical floor plan& typical Rebar Drawing …

AIM: 1. To Know the general design procedure of spread footing with safe software  2. To Know the general design procedure of pile foundation with safe software  PROCEDURE: SPREAD FOOTING : 1. Open the software  2. Select the New Model  3. Determine the units and other aspects  4. Determine the…

OBJECTIVE : 1. To know the general design procedure for spread footing  2. To practice how the inputs can be collaborated and arrived as data for calculation AIM: To Design of Shallow Foundation (Isolated Footings)

OBJECTIVE:  1. To model an apartment with all seismic considerations based on architectiral input  2. To Know how to check the seismic performance of an apartment using Etab    AIM: Using Etabs for structural modeling  PROCEDURE:  1. Open a new Etabs file for analysis and designing  2.…

Objective: 1. To know the design of the RC shear wall using Etabs analysis  2. To know the basics of shear wall reinforcement dealing with respect to the primary standard  3. To ensure the ductility reinforcement required by IS13920:2016 has been satisfied in the reinforcement drawing  AIM: To Analysis…

Objectives of the challenges : 1. To know the design of the RC column Using Etabs Analysis  2. To know the basics of RC column Reinforcement Detailing with respect to primary standards  3. To ensure the Ductility reinforcement required by IS-13920-2016 has been Satisfied in the reinforcement drawing  AIM: To design Reinforcement…

AIM:          i) To design the beams in detail from the Etabs           ii) To provide the detailing of longitudinal and shear reinforcement for two continuous beams.         iii) To calculate the value of maximum shear force in any one of…

OBJECTIVE = 1. To know how to extract Different seismic responses for the structure. 2. How to alter certain properties in the Etab model  3. Know the factor influencing the Dynamin characteristic of the building  4. Know the Factor influencing the time period of the building  5. know the Factor influencing…

OBJECTIVE : 1. To know the modeling of high-rise buildings in Etab Software  2. To verify the seismic code requirements from Etabs Analysis  AIM: To Model a 25-story building on ETABS with structural properties as specified  PROCEDURE:  1. Open the ETABS software. Click the file menu and choose…

OBJECTIVE: 1] To investigate the suitability of the given plan With respect to seismic behavior 2] To schematically draw a viable seismic structure.  Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three…

OBJECTIVE=1. To understand the impact of vertical and horizontal load members in a seismic behavior of a structure structure  2. To understand different irregularities in the building    Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions…

A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and its associated…

Q1. Differentiate Static analysis and Dynamic analysis by properly representing pictures ANSWER= STATIC ANALYSIS: 1. A Static Structural analysis calculates the effect of steady loading conditions on the structure  2. Static means stationary or fixed  3. Eg. Dead load  its intensity doesn't change over the…

1a]  OBSERVATION:  1. Concrete is crushed and the reinforcement is exposed  2. Concrete spalled beyond the reinforcement which may be a sign of the rupture. 3. Beam top portion look safe because of the flange advantage from the slab  4. The crack develops from bottom to top means rebar yielding occurs…

1) Use the Architecture/ Structure Project file developed by you in weeks 6 to 8. Export the Revit architecture and structure model to the Navisworks Cache file following the export settings discussed in class ANSWER= AIM: To Export the Revit architecture model to the Navisworks Cache file following the export settings…

 1) Using Dynamo creates a set of sinusoidal points and creates a curve and create a surface out of the curve. ANSWER= AIM: To Use Dynamo and create a set of sinusoidal points and create a curve and create a surface out of the curve. PROCEDURE: 1. Just open thy Dynamo 2. In order to create the sinusoidal point…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School ANSWER: Office Building  2) Assume reasonable assumptions for geographic and location details…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level AIM: To Model a Ceiling from the architecture tab above the walls at the first-floor level. PROCEDURE: 1. Open the project from challenge 3 2. click on the…

1.  AIM: To Draw the elevation and details of a wardrobe as shown in the Figure. PROCEDURE: 1. First and for most set the unit to decimal and mm  2. Then setup the dimension setting  3. Sketch the plan with the given dimension with the help of line and rectangular command  4. make sure you hatch…

AIM: To draw a 3D-rendered model for a residential building in Autocad PROCEDURE: 1. First and foremost change the unit to decimal and mm 2. Now create the layer for the model  3. Now create the plan for the building with the help of the layer created  4. BUILD-UP size of the building is 15450x6000mm  External…

1.  AIM: To Create a 3D Isometric View of the building with a plan and elevation given PROCEDURE: 1. First set the unit to engineering and inches  2. Creating the necessary layer for the project  3. Create the first object with the help of the BOX command of size 10'9"x10'9"x4" 4. Over that box create…

1. AIM: To Create a 3D Furniture element PROCEDURE: 1. First change the unit to engineering and inches 2. Then create a plan for the table with the help of the polyline command  3. Then turn it into REGION with the help of the region command  4. With the help of EXTRUDE command extrude it in the z-axis as per…

1.  AIM: To Create a layout of the Plan and Section A of the project in Challenges 7 PROCEDURE: 1. First set the page setup manager to opt for A1 paper size 841x594mm  2. Select the template from the cade file that is  Tutorial-mArch.dwt 3. Now with the help of the ATTEDIT command  edit the…

AIM: Create the layouts of the Kitchen and provide a hatches pattern  PROCEDURE: Set the unit to decimal and mm  First create a wall of thickness of 250mm Now create the counter wherever it's required as per the given dimension  Making all components required on the counter And label them with the number…

1.  AIM: To create the template as shown in figure PROCEDURE:  1. So basically we can use line, rectangle, offset and text commands to draw the templates. 2. And to convert it into the block we have to first invoke the block command 3. Make sure we have to invoke the command after creating the object  4.…

AIM= To design and draft a layout of a residential building for plot size 18.3x6m  PROCEDURE=  PLAN  1. Start with changing the unit to decimal and mm  2. Set the dimensional style manager  3. Creating the appropriate layer for drafting  4. Now start with the Architecture plan by drawing the…

  1. AIM: TO  Create a column schedule PROCEDURE :  1. Change the unit to engineering and inches. 2. Draw the tabular column with line and rectangular command 3. Use the Text command to create text in a tabular column  4. Use font name: Romans.shx; Height: 8”, Justify: Left 5. Create the…

1.O AIM:  To sketch the layout of the residence. Consider all dimensions as a reference to sketch the unit plan.  Procedure: 1. Change the unit to Engineering and inch  2. Determine the number of layers you need to create the layout  3. Eg: Layer 1 = Internal and External Walls Layer 2 = Staircase  Layer 3 =  Furniture …

1. AIM: To create geometries using the given command  PROCEDURE: 1. Change the unit to decimal and MM  2. Draw the outer boundary with the help of a line command  3. Use the relative Rectangular method and relative polar method for the outer boundary  4. Now use the circle command to draw the circle…

C1 AIM: To create the C.S of load bearing wall on the spread footing as per the given dimension in the attachment in the auto-cad with the help of the commands    COMMANDS USED:  LINE COMMAND  RECTANGULAR COMMAND  OFFSET COMMAND  DIMENSION COMMAND  TEXT COMMAND  TRIM COMMAND …

Aim: To Create the geometries for the given drawing using all the coordinates system methods. By using the line tool and circle tool  P1 Absolute Coordinate     P1 Relative Rectangular Coordinate  P1 Relative Polar Coordinate  P1 Direct Distance Coordinate    P2 Absolute Coordinate method  P2 Relative Rectangular coordinate …

AIM= To Sketch a G+1 Floor residential plan, According to Vaastu Shastra, list down the names of the structural drawing required to be provided to the site for construction, and compute the required load for column, beam and slab.    IMPORTANT STRUCTURAL DRAWINGS FOR A PROJECT Centre line drawing Footing and…

Aim: to determine the mix proportion of M30 Grade concrete using fly ash. 1] Stipulation for proportioning  a. Grade of desigination= M35  b. Type of cement= OPC43 c.Type of mineral admixture= Fly ash  d.Maximum nominal size of aggregate= 20mm e.Minimum cement content= 320kg/m^2 f.Maximum W/C ratio=0.45…