3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
ANS 1
AIM : TO MODEL A CEILING FROM THE ARCHETECTURAL TAB ABOVE THE WALLS AT THE FIRST FLOOR LEVEL
PROCEDURE :
- Open revit software and click on new to open the architectural template file
- In the file tab , load the week 3 project that we did earlier
- Now we have to create the celling to this first - floor level
- Go to the architectural tab and click on celling
- There are two methods for creating the celling
- For this floor plan , we use the sketch celling portion
- We select the sketch the celling option from the architectural toolbar
- pick the exterior lines of the wall carefully
- Click on the green tick mark and press Esc to close
RESULT :
The celling for the first - floor level has been created successfully for the residential building
ANS 2
AIM : TO MODEL A ROOF ABOVE THE CELLING BY SELECTING THE FOOTPRINTS OF THE CELLING
PROCEDURE : STEP
- Open the architectural toolbar and select the roof by footprint option
- Next we select the roof and adjust the roof to 10 degree by selecting it
- The roof has been created
RESULT
The roof has been created successfully to the model in the revit in detailed manner
AIM : TO CREATE PLAN VIEWS FOR A GROUND FLOOR LEVEL INCLUDING ALL THE WALLS , FLOORS ,AND COMPONENTS
AND TO SEPARATE THEM TO ARCHITECTURAL AND STRUCTURAL PLAN
PROCEDURE : STEP
- First we draw the architectural plan of first floor and second floor
- Next we draw the structural plan of the first floor and second floor
RESULT :
- Created plan view for ground floor level and first -floor level including all the walls , floors , and components
- and separated them to architecture and structural plan
ANS 4
AIM: TO ADD DIMENSIONS TO ALL THE WALLS AND FLOOR WITH REFERENCE TO THE LONGITUDINAL AND TRANSVERSE GRIDS CREATED IN THE PROJECT FILE
PROCEDURE : STEP
- Here we draw the longitudinal and trasverse grids to the architectural floor plan
- And add the dimension to the architectural plan
- Next we draw the longitudinal and transverse grids to the structural floor plan
- And add the dimension to the structural plan
RESULT :
- The dimension are added to the structural floor plans and the architectural floor plans
- And the longitudinal and transverse grids are also created in the project file
ANS 5
AIM : TO CTREATE A SHEET TEMPLATE FROM THE VIEW TAB AND ADJUST THE PARAMETER ON THE SHEET TO ADD APPOROPRIATE VIEWS
PROCEDURE : STEP
- First we click on the sheet option from the view toolbar
- After the clicking the sheet , The new tab will be visible on the screen
- In that new tab we select the A1 metric , then the sheet template will be displayed
- In the sheet template we insert the first floor plan and second floor plan separately
Next edit the project name and the sheet number
RESULT :
Created a sheet template from the view tab and ajusted the parameters on the sheet for adding appropriate views .
ANS 6
AIM : TO CREATE THE ELEVATION VIEWS LOOKING AT YOU BUILDING FROM EAST , NORTH ,SOUTH , AND WEST USING THE ELEVATION TAB
PROCEDURE : STEP 1
- First we click on the elevation option from the view toolbar
- Next the elevation from the east will be visible
- Next the elevation from the south will be visible on the screen
- Next the elevation from the north will be visible on the screen
- Next the elevation from the west will be visible on the screen
ANS 7
AIM : TO PRODUCE SECTION CUT THROUGH EACH ROOM EITHER CUTTING ACROSS LONGITUDINALL OR INA TRANSVERSE DIRECTION
PROCEDURE : STEP
- First we click on the section option from the view toolbar
- Next we produce the section view of the bed room
- next we produce the section view of the toilet room
- Next we produce the section view of the kitchen room
- Next we produce the section view of the living room
RESULT :
Created the section view of a model in the revit in detailed manner
ANS 8
AIM: TO CLASSIFY THE VIEW PLAN VIEWS , SECTION VIEWS AND ELEVATION VIEW TO EITHER DESIGN OR DOCUMENTATION CATEGORY USING PROPERTIES BROWSER
PROCEDURE : STEP
- First we open the project browser , the views, plan view, section views and elevation views are visible in that project browser
- Next we insert these plans one by one in the sheet saparetly
- first we insert the front elevation in the sheet template
- next we insert the left side elevation in the sheet template
- Next we insert the right side elevation in the sheet template
- Next we insert the back side elevation in the sheet template
- Next we insert the first floor plan in the sheet template
- Next we insert the section 1 in the sheet template
- Next we insert the section -1 in the sheet template
RESULT :
View , plan views , section views and elevation views are classified to design category using properties browser
ANS 9
AIM : TO CREATE THE MULTIPLE SHEETS AND PRODUCE THE DRAWINGS IN THE SHEETS , FROM THE GIVEN DRAWING LIST
PROCEDURE : STEPS
- First we produce the groodfloor plan in the sheet template A - 101
- Next we produce the first floor architectural plan in the sheet template A- 102
- Next we produce the roof plan in the sheet template A- 103
- next we produce the ground floor structural plan in the sheet template s - 101
- Next we produce the first floor structural plan in the sheet template s -102
- next we produce the roof framing plan in the sheet template s- 103
- Next we produce the east ands west elevation view in the sheet template A-202
RESULT :
Created the multiple sheets and produced the drawings in the sheets , from the given drawing list
ANS 10
AIM : To create a camera specific view or a 3d view in living room , dinning room and bredroom in the sheets separately.
PROCEDURE : STEP
- First we take the go sheets and name it as A -501
- next go to the floor plan and place the camera in the bed room , and the camera view of bedroom will be
- Next we take the sheets and name it as A-502
- Next go to the floor plan and place the camera in the kitchen room and the camera view of kitchen room will be
- Next we take the sheet and name it
- Next go to the floor plan and place the camera in the living room , and the camera view of living room willbe
RESULT: room and a camera specific view or a 3D view in living room , dinning room and bedroom in the sheet separattely