3D Creation of Ceiling, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level

Answer =

Aim :- Model a Ceiling from the architecture tab above the walls at the first-floor level

Introduction :- To create the ceiling like wise the roofs and floors.The main thing is that to check the ceiling before we start.

Procedure :-

• First we open the revit sofware, and select the ceiling option from the architecture toolbar.
• After selecting the ceiling option, then select the each room one by one.
• Then the ceiling will be created, as shown in the below figure.
• View it on the 3D view
• The ceiling has been modeled successfully from the architecture tab above the walls at the first-floor level.

2) Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees

Answer =

AIM = Model a roof above the ceiling by selecting the footprints of the ceiling.

Introduction =

• Roofs have been constructed in a wide variety of forms flat, pitched, vaulted, domed, or in combinations as dictated by technical, economic, or aesthetic considerationsThe earliest roofs constructed by man were probably thatched roofs that were made of straw, leaves, branches, or reeds; they were usually set at a slope, or pitch, so that rainfall could drain off them.

Procedure =

• Open the architecture toolbar, and select the Roof by Footprint option.
• Next we select thr roof and adjust the roof to degree by selecting it.
• The roof has been created, as shown below.
• The roof has been created successfully to the model in the revit in detailed manner.

3) Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to architecture and structural plans

a. Architecture plan must have walls, floors, and all the components placed within the building
b. Structure plan must have details of only walls, floors, and columns

Answer =

AIM =

• To create plan views for ground floor level and first-floor level including all the walls, floors, and components And to Separate them to architecture and structural plans

INTRODUCTION =

• The structural plan view is the default view when you start a new project using a structural template. . Most projects include at least one structural plan. New structural plan views are created automatically as you add new levels to your project. You can create multiple structural plan view types
• The floor plan view is the default view in a new architectural project. - Most projects include at least one floor plan.
• Floor plan views are created automatically as you add new levels to your project.

PROCEDURE =

• First we draw the architectural plans of first and the second floor
• Next draw the structural plans of first and secoond floor plans
• the plan views for ground floor and first floor has been created.
• Both the architectural and structural view is created.

4) Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file

a. The architecture plan dimensions include details on where the components are placed within the buildings with relation to grids. Overall dimensions are sufficient for architecture plans

b. The Structure plan dimensions must include details on the position of all the walls and interior walls with reference to grids. Locate all the framing components of the building with reference to a fixed point using Structural plans

Answer =

AIM:- To add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file.

INTRODUCTION:-

• The structural plan view is the default view when you start a new project using a structural template.
• Most projects include at least one structural plan. New structural plan views are created automatically as you add new levels to your project. You can create multiple structural plan view types.
• The floor plan view is the default view in a new architectural project. Most projects include at least one floor plan.
• Floor plan views are created automatically as you add new levels to your project.

PROCEDURE:

• Here we drawn the longitudinal and transverse grids to the architectural floor plans as shown below.
• And add the dimensions to the architectural plans as shown below.
• Next we draw the longitudinal and transverse grids to the Structural floor plans as shown below.
• And add the dimensions to the Structural plans as shown below.
• The dimensions are added to the structural floor plans and the architectural floor plans.
• And the longitudinal and transverse grids are also created in the project file.

5) Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views

Answer =

AIM

• To create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views

INTRODUCTION

• Create views on a project template before you start building the model to streamline the project documentation process.
• When creating a project template you can include sheets in the template Start with a blank project file and create the standard views and levels that each project should include
• Leave the views empty but assign standard names to them. To create a standard set of construction documents, create sheets using the desired title blocks
• Add views to the sheets, using the desired viewport templates and view title types
• Then save the empty project as a project template.
• When you create a project using this project template, all of the views and sheets are already created and listed in the Project Browser
• As you start to draw the building model in the project views, the views on the sheets update automatically.
• This technique streamlines the project documentation process and maintains organizational standards.

PROCEDURE ]=

• First we click on the sheet option from the view toolbar, as shown below.
• After clicking the sheet. The new tab will be visible on the screen.
• in that new tab we select the Al metric, then the sheet template will be displayed.
• In the sheet template we insert the first floor plan and second floor plan separately as shown below.
• Next edit the Project name and the sheet number as shown in the below figures.
• Created a sheet template from the view tab and adjusted the parameters on the sheet for adding appropriate views.

6) Using the elevation tab create the elevation views, looking at your building from East, North, South, and West

Answer =

AIM:- To create the elevation views, looking at your building from East, North, South, and West using the elevation tab.

INTRODUCTION:-

• An elevation is a view of a building seen from one side, a flat representation of one view.
• This is the most common view used to describe the external appearance of a building.
• Each elevation is labelled in relation to the compass direction it faces, e.g. looking toward the north you would be seeing the southern elevation of the building.

PROCEDURE:-

• First we click on the elevation option from the view toolbar
• Then Click on East West South And North In the elevation tab
• then all sides will be covered

7) Produce section cut through each room either cutting across longitudinally or in a transverse direction

Answer =

AIM:- To produce section cut through each room either cutting across longitudinally or in a transverse direction.

INTRODUCTION:-

• Sectional views reveal hidden details in a mechanical drawing.
• These views assume that a cutting plane has removed portions of the object represented by the drawing, displaying the appropriate section of the interior.
• Sectional views are used in engineering and architectural drawings.
• They help civil engineers, architects, and airplane designers communicate their ideas to their peers.

PROCEDURE:-

• First we click on the section option from the view toolbar, as shown below.
• Next we produce the section view of the bed room and each room of the plan as shown in the below figure.

8) Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser

Answer =

AIM:- To classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser.

INTRODUCTION:-

• The structural plan view is the default view when you start a new project using a structural template.
• Most projects include at least one structural plan. New structural plan views are created automatically as you add new levels to your project. You can create multiple structural plan view types.
• The floor plan view is the default view in a new architectural project. Most projects include at least one floor plan.
• Floor plan views are created automatically as you add new levels to your project.
• Sectional views reveal hidden details in a mechanical drawing.

PROCEDURE:-

• First we open the project browser, the views, Plan Views, Section Views, and Elevation views are visible in that project browser as shown below.
• Next we insert these plans one by one in the sheets separately.

9) Using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations

Add additional sheets based on the sections created in your Revit file

Answer =

AIM:- To create the multiple sheets and produce the drawings in the sheets, from the given drawing list.

INTRODUCTION:-

• Create views on a project template before you start building the model to streamline the project documentation process.
• When creating a project template, you can include sheets in the template. Start with a blank project file, and create the standard views and levels that each project should include.
• Leave the views empty, but assign standard names to them. To create a standard set of construction documents, create sheets using the desired title blocks.
• Add views to the sheets, using the desired viewport templates and view title types.
• Then save the empty project as a project template.
• When you create a project using this project template, all of the views and sheets are already created and listed in the Project Browser.
• As you start to draw the building model in the project views, the views on the sheets update automatically.
• This technique streamlines the project documentation process and maintains organizational standards.

PROCEDURE:-

• First we produce the Ground floor architectural plan in the sheet template A-101
• Next we produce the First floor architectural plan in the sheet template A-102
• Next we produce the Roof plan in the sheet template A-103, as shown in the below figur
• Next we produce the Ground floor structural plan in the sheet template S-1
• Next we produce the First floor structural plan in the sheet template S-102
• and so on we will produced Plans for the other plans.

10) Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets starting A-501 (you can add as many sheets after, 502, 503.. n)to place the 3D view images. Produce the sheets as a part of project drafting.

Answer =

AIM:- To create a camera-specific view or a 3D view in living room, dining room and bedroom in the sheets separately.

INTRODUCTION:-

• Camera Views are really useful in Revit.
• They allow us to view what we would actually see if we were standing at any given location in our design.
• This can be invaluable for both understanding and communicating the nature of a space before we go to the expensive lengths of actually constructing it for real.

PROCEDURE:-

• First we take the sheet and name it as A-501.
• Next go to the floor plan and place the camara in the bed room, and the camera view of bed room will be shown below.
• Next we take the sheet and name it as A-502.Next go to the floor plan and place the camara in the Kitchen room, and the camera view of kitchen room will be shown below
• Next we take the sheet and name it as A-503.Next go to the floor plan and place the camara in the Living room, and the camera view of Living room will be shown below.