BENCH MARKING Benchmarking is a process where you measure the performance of a company’s products, services, or processes against those of another business considered to be the best in our knowledge. Or we can say benchmarking is a process in automobile industry which we compare the performance of measuring products,…

 Underbody Coating   Underbody Coating is usually a dense cladding (often based on Rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if the underbody coating is applied on the car after a couple…

AIM: Our aim for this project is to create a hood assembly from the hood outer panel which is provided as input surface to us according to the master section sketch. Software used: Siemens NX 12.01 the report contains 1.introductions 2. Design Consideration 3. Design 4. Draft Analysis 5. Conclusion Introduction: Bonnet…

 SECTION MODULUS OF AN HOOD Section modulus is a direct measure of strength of any  sectional area of an object about an reference axis(neutral axis). Strength is nothing but, capable of supporting greater loads, so higher the strength it has a high capable of supporting  greater loads. This strength can measured directly…

 WHEEL ARCH CHALLENGE Aim :     To Calculate the Wheel Arch Area by given fender and Wheel Model Design and Prove whether the car will pass by using European standards or Not. Introduction : The wheel arch is the semicircular part positioned above the wheel of a vehicle. Designing of wheel arch…

FENDER DESIGN AIM: To design a  front fender of a car by following the given master section as per the design considerations of OEM. INTRODUCTION : Fender is the american english term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well. Its primary propose is to prevent sand,…

ROOF DESIGN OBJECTIVE : The objective of this project is to design car roof with  essential flanges and reinforcements  like ditch area , front roof rail , bow roofs, central roof rail and rear roof rail for the the given styling surface Perform a curvature study on the roof and perform the calculations for the…

                                                                 DESIGN OF BACKDOOR OBJECTIVE To design the back door of a To design an inner panel for the…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. REPORT ON DRAFT ANALYSIS: Given Class A Surface: STEP 1: Check…

DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL OBJECTIVE The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help of Bisecting method. INTRODUCTION The control panel bezel is the frame part of the window switch that holds its switch…

COIN HOLDER To create a coin holder plastic component by closed method with reference to the class A surface and do the draft analysis for the component. Steps followed The class A surface is checked for the connectivity of the surface and ensure it is completely joined and there will be no gap between the surfaces. If…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface.CLASS-B SURFACE: a surface below a certain thickness from the class-A…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  TOOLS USED: Boundary Join Multiple extract Bisecting…

Attachment Feature Creation - Challenge 2  AIM Create the Dog House for the Door Trim considering the design rules INTRODUCTION DOG HOUSE Dog house is an engineering feature used in plastic design. Dog houses are used as support feature. Sometimes other engineering features like snaps, locators, and screw bosses are…

Objective: The main aim of this challenge is to create a solid body of 'Door Trim Lower' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Door trim. Given sample design Overview:Initially, we need…

AIM :- To create assemblies of Quick return mechanism and CV joint and to also create 2D drawing of the given assemblies in CATIA.  ASSEMBLY :- Assembly modeling is a technology and method used by computer-aided design and product visualization computer software systems to handle multiple files that represent components…

A-PILLAR DESIGN WITH MASTER SECTION AIM: To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. CLASS A SURFACE:           Class A is an aesthetic surface with the highest quality…

NOTE: I have Attached the Report, Photos and CADpart in the Attachment Week 12- Final project AIM: To develop the Door Trim panel OBJECTIVE: Creation of CAD model considering following inputs as like in OEM and tier1 companies a) Class A surface b) Nominal thickness : Refer master sections c) Attachment strategy : …

Objective:      To design of Butterfly Valve body in appropriate dimension with the application of GD&T - ASME Y14.5 2009. To understand the concept of geometric tolerance and dimensioning.  Softwares Used Siemens NX 12  Introduction         Siemens NX…