Mix design for M35 grade concrete with fly ash.  STEP 1- Stipulation for proportion  • Grade of design - M35  • type of cement - OPC 43  taken from the  IS 8112 • Type of mineral admixture - fly Ash  • Maximum nonimal size of3 aggregate - 20MM  •Minimum cement…

Aim -   To sketch a G+1 floor residential plan according to vastu Shastra and to list down the names of structural drawings required to be provided to the site for construction. To assume the size of structural elements (Column, Beam, slab etc) and to calculate the loads from the members as per IS code.   Dimensions of…

TASK: Create the geometries from Pl to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where required you need to use the circle tool. Please read the drawings and find out the missing dimensions before working on the sketches.  Note: Use the Imperial Template and…

AIM:  To Creating a Floor plan, Footing detail and Isometric view using AutoCAD.   INTRODUCTION: The main objective of this assignment is to get in touch with various tools in AutoCAD like the rectangle, polylines, modifications tools like copy, move, offset and modes like snap mode and ortho mode. These…

AIM : To draw the given drawing using AutoCAD software PROCEDURE STEP 1 : • In the command prompt type Units and select decimal unit STEP 2: •In the command prompt type PL (Polyline) In the command prompt specify start point 1,1 In the command prompt type @3<0 In the command prompt type @2.12 <45 In…

  Q1) AIM: To draw the given residential plan with the details given.   INTRODUCTION: Residential Layout is ideal for students and practitioners of urban design, planning, engineering, architecture and landscape seeking a comprehensive guide to the theory and practice of designing and laying out residential areas.…

AIM:   To create a column schedule as given in figure by using AutoCAD   Introduction:The column schedule is created by the help of line tool. Specification of the column schedule wrriten by the text    command. The step-by-step procedure are as followed and result shown by the diagram  …

Q1  Step1: The plan of the wardrobe is drawn with the help of horizontal and vertical construction lines. The doors of these cabinets are drawn with the help of arc and line command as shown in the figure. Step2: The front elevation of the same is drawn of the same size and with the help of line command it is achieved. …

  AIM:To Design and Draft a layout of a residential building with plot size (18.3 m x 6 m)  Commands Used: xl  offset trim Extension ADC (design centre ) line rectangle lt (linetype) arc Procedure: step 1: In the command prompt type Units >meters  In the command prompt type limmax >100,100 In…

Q1  Aim:To create the templates using autocad command and tools as per drawing required. Introduction:  Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can assume it as per the size of the paper. Use text and attributes wherever required. After creating…

Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm.   Procedure:-   step 1:- units are set to mm limits and limax are also set zoom comand is also used Steps for drawing Below Counter Plan…

 INTRODUCTION:-   A drawing template file is a drawing file that has been saved with a . dwt file extension, and it specifies the styles, settings, and layouts in a drawing, including title blocks. The default drawing template files are provided as samples. Efficiency is also gained through template files because…

1. Create a 3D Furniture element as shown in the Figure. Assume dimensions that are missing.   AIM: To create a 3D model of the Furniture element as per the given drawing    INTRODUCTION: 3D modeling in AutoCAD includes 3D solids, surfaces, meshes, and wireframe objects.   Types of 3D Models:  …

1. Create a 3D Isometric View of the building with plan and elevation given.   AIM:- To create a 3D isometric view of the given building with plan and elevation.   INTRODUCTION:-    An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. One of the defining…

Create a 3 dimensional model of the residential building with a rendered view.  AIM: To create a 3 dimensional model of the residential building  To create a rendered view of the developed model. To use materials and light setting.   Procedure: Here in the project we are going to create a 3d model of a residential…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level.       AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level.       INTRODUCTION:-  …

Q1)   AIM:    Select the type of structure you want to build from one of the three below:         a. Multi-Unit Residential Apartment         b. Office Buildings         c. School.   ANS) OFFICE BUILDING   Q2)   AIM :    Assume…

Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo   Introduction:   Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code; while…

  1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class   Aim: Using the Architecture/ Structure Project file developed and exporting the Revit architecture and…

1. Write the steps involved to upload a .std file through web mail?     Steps involved to upload a .std file through web mails are as follows;   Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then,…

1.   1. How will you assign Circular section to column? Open STADD Pro Software. Create two nodes in vertical direction since it is a column. Then go to properties and create new property. Select circular and give the diameter. Then press ok. The property will be created. Then select the property and use curser to…

1. 1. State the primary load cases to be considered for design.   Ans: Dead Load         Live Load         Snow Load         Seismic Load         Wind Load      …

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180 kN/m2…

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows: Width 30m Length50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements. Follow IS800:2007, IS1893 and IS…

1.What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as a failure? Are the damages repairable? Elaborate Answer:   a. The above image shows a Damage at the Beam-column joint. It is clearly observed that the Damage is more for the part of Beam. The Damage…

1. Differentiate Static analysis and Dynamic analysis with proper representing picture.   Static Analysis: Static analysis of structures considers static loads acting on the structure such as dead,live load which does not vary with time and are not considered to be sudden. In static analysis stiffness matrix alone…

  Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived.