Project on Concrete Mix Design for various grades of Concrete  Calculate the Concrete Mix Design for M35 grade concrete with fly ash & M50 grade concrete without Fly ash  AIM: To Calculate the Concrete Mix Design for M35 grade concrete with fly ash & M50 grade concrete without Fly ash  INTRODUCTION:…

the drawing and the answers are been attached in the below document

Creation of geometries by Coordinate system methods using AutoCAD  *************************************************************************************  Create the geometries from P1 to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where required you need…

Creating a Floor plan, footing detail and Isometric view using AutoCAD  ************************************************************************************  Cross section of load bearing wall over spread footing.  Aim: To draw cross section of wall over footing.  Commands used:  Line. …

Drafting of various geometries using Chamfer, Fillet tool in AutoCAD  **********************************************************************************  AIM: To draw the geometries using Chamfer, fillet tool in AutoCAD.  Commands used: Line, circle, chamfer, fillet, mirror, trim, move, rotate, annotate. …

Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCAD  *************************************************************************************  Aim: To draw the layout of a residence plan.  Commands used:  XL-V OR XL-H.  Offset.  Fillet.  Extend. …

Creation of Column Schedule and Drawing Template using AutoCad ************************************************************************************** 1. Create a column schedule as shown in figure     INTRODUCTION   1. Column C1 is provided with 4 bars of 20 mm dia. and 6 bars of 12 mm dia. The 12 mm dia…

Creating a Wardrobe detailed drawing, Floor Plan, Kitchen Layout and Column Detail using AutoCAD  *********************************************************************************  1. AIM:  To draw the elevation and details of a wardrobe as shown in the figure. After sketching, WE need to provide…

Creating a Layout, Section and Elevation with dimensions using AutoCad  **************************************************************************      Aim:- To draw the floor plans and sections using the proper dimension techniques and dimension styles to document the project.   …

Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings  ************************************************************************************    Aim: To draw the plan, section and elevation of a building by the given plot area.  Architectural drawing…

Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCAD  ******************************************************************************************* Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can…

Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCAD  ******************************************************************************************************* 1) Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever…

Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCAD  ****************************************************************************** 1) Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure.…

  Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCAD  ***********************************************************************************  AIM: To create 3D model and view of:  Furniture element  Isolated footing  AASTHO type girder …

Creating 3D Isometric view of various structural elements in AutoCAD    Commands Used in this challenge  Line  Rectangle  Trim  Move  Copy  Explode  Circle  Dim linear  Dim continue  Boundary  3Dorbit  3D rotates  Extrude  Region  UCS …

Project 2_Creating a 3D rendered model for a Residential Building in AutoCAD  ********************************************************************* PROJECT- 2  AIM OF THE PROJECT:   Creating a 3D rendered model for a Residential Building in AutoCAD.     INTRODUCTION- COMMANDS USED FOR…

3D Creation of Ceiling, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT    Aim:  To create the ceiling above the walls at the first-floor level.  Procedure:  Initially open the week 3 assignment from the Revit software. …

  Creating Architectural and Structural model with 3D rendering using REVIT  Introduction  Revit enables the project to be completed in a combined effort. Structural engineers that are using Revit and are working with architects using Revit Architecture can directly link to the architectural model. Linking…

Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo 1. Aim: To create a set of sinusoidal points, a curve and a surface out of the curve using dynamo. Procedure:  Initially, open the architecture template of Revit software and go to manage tab. In manage tab select…

Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork 1)  AIM: To use the architecture/structural project file developed from week 6-8, Export the Revit file to Navisworks cache file. PROCEDURE : 1.the Revit file which is to be exported to the Navisworks file is to be opened with the help…

1. Write the steps involved to upload a .std file through web mail? Steps involved to upload a .std file through web mails are as follows; Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then, browse for the. Std…

WEEK 2 CHALLANGE FOR STAAD PRO ******************************************************************************************** Question 1. How will you assign Circular section to column?     2. How will you assign Unit system to a .std model file?     3. What are the parameters to be specified while…

WEEK 3 CHALLENGE IN STAAD PRO *********************************************************************************** Q1. State the primary load cases to be considered for design. The primary load cases that are to be considered for design are listed below: Dead Load (IS 875: Part I). Live Load (IS 875: Part II). Wind Load…

PROJECT 1 IN STAAD PRO   Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows: Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity…

1) Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements.…