Aim :- The aim is to draw all the objects using absolute rectangular and polar coordinate system Introduction:- we will draw all the objects using different cordinates system. In this we have absolute cordinate system in which we will use the origin point as a refrence to give the various commands. In rectangular system…

Aim Sketch a G+1 residential plan according to Vaastu Shastra and Calculation of Loads as per IS code Introduction Here we are going to Sketch the G+1 Residential Plan of height 3 m according to Vastu and also we will calculate the Dead load,Live Load and wind Load on the building. Procedure Calculation Of Dead Load  …

1.Aim: To determine the mix design for M35 concrete with fly ash consisting of the following properties: Grade designation : M35 Type of cement : OPC 43 grade (confirming IS 12269) Type of mineral admixture : Fly ash Maximum nominal size of aggregate : 20 mm Minimum water-cement ratio : 0.45 (Table 5 of IS 456:2000) Workability…

1. AIM:- Design and Draft a layout of a residential building with the following details: a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East    c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections)              …

Aim:- Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad Introduction:- In this challenge we are going to design some doors, templates. Also we will create the blocks of those design and insert them in our auto cad file. Procedure:- 1. Create the templates…

AIM:- Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad INTRODUCTION:- In this challenge we are going to do hatching using H command. Also we will be using various patterns of the hatching, with the help of which we will hatch objects of our auto cad file.…

AIM:- Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad INTRODUCTION:- In this challenge we are going to create various layouts of the plans with the help of various commands like layout, model space,paper space,page setup etc. For creating the layouts firstly we have to set the size…

AIM:-  Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad Introduction:- In this challenge we are going to create 3d models in auto cad. For 3d we have to extrude a 2d image and the thickness is provided to the model. Procedure:- 1. Create a 3D Furniture element…

1.Create a 3D Isometric View of the building with plan and elevation given.   2.. Create the 3D View of the Building Façade as given in the plan and elevation. Also, see the detail of the window.   3.Create the ismoteric 3d view of a stair with railing as shown in the plan and elevation. Assume the size…

Aim:- Create a 3 dimensional model of the residential building with a rendered view.   Introduction:- In this project we are going to create a 3d model of a residential building. Rendering is a process in which the solid blocks are given texture using various materials like paint,glass, concrete,wood etc. AutoCAD…

1. 1. Write the steps involved to upload a .std file through web mail? ANSWER Steps involved to upload a .std file through web mails are as follows:- Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then, browse for…

1. 1. How will you assign Circular section to column? ANSWER Go to properties tab Click on define Select circle Give diameter of column and choose material     2. How will you assign Unit system to a .std model file? ANSWER We have two ways in which we can assign the Unit system to a .std model file, they are:…

1. 1. State the primary load cases to be considered for design. The primary load cases that are to be considered for design are listed below: Dead Load (IS 875: Part I). Live Load (IS 875: Part II). Wind Load (IS 875: Part III). Snow Load (IS 875: Part IV). Seismic Load (IS 1893: 2016).    …