Objective: To simulate the full hydro setup of a Port-fuel injection engine which uses Iso-octane (IC8H18) as the fuel and based on the results from the simulation evaluate the following parameters: Compression ratio of the engine. The need of a wall heat transfer model and why can\'t we predict the wall temperature from…

Objective Setup the case to simulate flow through a solid pipe using CONVERGE and visualize the conjugate heat transfer between the pipe walls and the fluid flowing inside the pipe using Paraview. Perform grid dependency test. Study the effect of super-cycle stage interval on the simulation time. Introduction Conjugate…

Introduction Throttle valves are used to control the amount of fuel flow and have main application in carburetted fuel systems. In this project, a steady-state flow is simualted in an elbow joint that contains a throttle valve which remains stationary throughout the simulation. Objective To perform steady-state simulation…

Objective To run closed cycle simulation of a CAT3410 Engine with two different piston profiles: Open-W and Omega. To characterize the emissions (Soot, NOx and UHC) and compare IMEP and power values. Introduction With the rising competition in engine industry and emission restrictions due to the environmental concerns,…

Objective To setup a transient shock tube simulation and plot the: Pressure and temperature curves and explain the result Cell count as a function of time and explain the result. Introduction Shock waves A shock wave is a propagating discontinuity in a flow that travels faster than the speed of sound. Shocks are very thin,…

Introduction Throttle valves are used to control the amount of fuel flow and have main application in carburetted fuel systems. In this project, a transient flow is simualted in an elbow joint that contains a throttle valve. Objective To perform transient simulation in an elbow joint containing a throttle valve and post-processing…

Objective To simulate the flow through a backward facing step with three base mesh sizes and post process the results using Paraview software. Geometry                                                 …

Objective To visualize the Prandtl Meyer expansion fan over an expansion corner using Converge and Paraview software and also understand the effect of Sub-Grid Scale(SGS) on the shock location. To study types of boundary conditons used for shock problems. To understand the reason of usage of Neumann boundary condition…

Aim To apply Reynold's decomposition to the NS equations to get the RANS equations and expression for Reynold’s stress.                  1. Understanding of the term Reynold's stress.                  2. What is turbulent viscosity?…

Aim: To model transmission belt, kick stand, rear fender and front fender of an Americsan chopper using Solidworks. Commands used: Following were the commands used to model the parts,  2D sketch Offset entities Extruded boss base Fillet Trim Spline 3-point arc Smart Dimensions Appearance Dome Dynamic Mirror Entities…

Aim: To model oil tank, chain and pedal of an American chopper using Solidworks. Commands used: Following were the commands used to model the parts,  2D sketch Offset entities Fillet Spline 3-point arc Smart Dimensions Appearance Dome Mirror Chamfer Shell Combine feature Linear pattern Curve driven pattern Extruded…

Aim To model rear wheel and front fork of an American chopper using Solidworks. Objective Understanding the projected curves and revolve cut features by designing the rear wheel and the front fork. Rear wheel Components: Rim, rotor, tyre, sprocket and caliper. Commands used: Following were the commands used to…

Aim To create photorealistic rendered images of the American Chopper using Solidworks Visualize. Rendered images: Following are the rendered images, Downtown Route 66 Fall street Sunny Driveway  

AIM & OBJECTIVE To create different parts of a Sunseeker Predator Yacht in Solidworks using various types of sketches, features and surfacing tools. To assemble the different modelled parts to create a Yacht. To create photorealistic rendered images of the Yacht using Solidworks Visualize. INTRODUCTION …

AIM & OBJECTIVE To create different parts of a American chopper in Solidworks using various types of sketches and features tools. To assemble the different modelled parts to create the chopper. To create photorealistic rendered images of the chopper using Solidworks Visualize. INTRODUCTION  The chopper…

TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Casing Design. OBJECTIVE: To design a Sheet metal Casing and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one…

TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Box Assembly. OBJECTIVE: To design a box assembly and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of…

TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Odd shaped enclosure. OBJECTIVE: To design an odd shaped enclosure and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal…

TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Bracket. OBJECTIVE: To design a bracket and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of the fundamental…

TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Metal Bracket-II. OBJECTIVE: To design a metal bracket and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of…

TITLE OF THE PROJECT: Final Independent Project - Modelling and rendering of Audi A7. OBJECTIVE: To model and assemble an Audi A7 using Solidworks and render it using Solidworks Visualize. INTRODUCTION Solidworks It is a solid modelling computer-aided design (CAD) and computer-aided engineering (CAE) computer…

Screw 1 (To connect the disc and shaft) Following are the images of the screw; Front and back view Top view Bottom view Right and left side view Isometric view Below is the link of the file containing modelled part; https://drive.google.com/file/d/1EBDN-Y63TsVxu1ujtqHdYykBa88ta9gy/view?usp=sharing  Screw 2 (To…

INTRODUCTION A car’s underbody is exposed to the most wear and tear caused by muddy water, potholed roads, stones and other obstacles on the road. Because it’s not in plain sight, we often do not see the damage. In Indian road conditions, a car’s underbody is most prone to corrosion. Underbody coating…