ISRO Scientist/Engineer Electronics 2025 paper: Part A, questions 61 to 80, solved

Questions 61 to 80 of the ISRO Scientist/Engineer 'SC' Electronics written test of 26 Oct 2025 (Set A): 20 questions, each solved by Skill-Lync and checked against ISRO's final answer key.

Question paper and answer keys published by ISRO's Centralised Recruitment Board; solutions by Skill-Lync · Updated 18 Nov 2026 · 20 of 80 questions on this page

ISRO 2025 · Electronics Set A · Q.61Part A · 1 mark · -0.33 if wrongAnalog circuits

Average output voltage of a full-wave SCR rectifier at 60 degrees firing angle

In a single-phase full-wave controlled rectifier using SCRs with a resistive load, the firing angle is set to . Which of the following statements is TRUE regarding the average output voltage ()? Assume ideal conditions. = the peak input voltage
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (a) Official final key: (a) · provisional key was (c)

With a resistive load each SCR conducts from to in its half-cycle, and the output repeats every (full-wave). The average is taken over that period of :

At this is , which matches option (a).

The other options fail a check at (a plain full-wave rectifier, ): (c) gives , double the correct value, with at ; (b) gives zero at ; and (d), , is not the average for any of these cases: with a highly inductive load (continuous conduction) the average is , so (d) also misses the factor .

, option (a).

ISRO's provisional key (Oct 2025) and its December 2025 key both gave (c); the final key of 15 May 2026 changed it to (a).

Where this shows up in industry

Phase-controlled rectifiers like this regulate DC bus voltage in battery chargers, DC motor drives and ground-station power supplies by delaying the firing angle.

ISRO 2025 · Electronics Set A · Q.62Part A · 1 mark · -0.33 if wrongCommunications

What closes an eye diagram vertically and horizontally in a digital link

The eye diagram of a digital communication system closes vertically and horizontally due to
  1. (a)Inter-symbol interference only
  2. (b)Timing jitter and ISI
  3. (c)AWGN only
  4. (d)Synchronization drift only

Answer: (b) Timing jitter and ISI Official final key: (b)

An eye diagram overlays many symbol intervals. Its two openings measure two different margins:

  • Vertical opening (noise margin): shrinks with inter-symbol interference (ISI) from bandwidth limits and with additive noise.
  • Horizontal opening (timing margin): shrinks with timing jitter, which spreads the zero crossings, and with ISI, which skews the pulse edges.

Closure in both directions therefore needs both effects: timing jitter and ISI, option (b). ISI alone or AWGN alone mainly attack the vertical opening, and synchronisation drift only moves where the eye is sampled.

This is a conceptual question. The reasoning here is the standard textbook one, not a calculation.

Where this shows up in industry

Eye diagrams are the first thing engineers check when bringing up a high-speed serial link, a telemetry downlink or a SerDes channel, to see how much jitter and ISI margin is left.

ISRO 2025 · Electronics Set A · Q.63Part A · 1 mark · -0.33 if wrongAnalog circuits

Relative resistance change of a strain gauge with gauge factor 2.0 at 250 microstrain

A strain gauge with a gauge factor of 2.0 is connected in a Wheatstone bridge and subjected to a strain of . What is the relative change in resistance () of the gauge?
  1. (a)250 ppm
  2. (b)125 ppm
  3. (c)500 ppm
  4. (d)1000 ppm

Answer: (c) 500 ppm Official final key: (c)

Gauge factor is defined as , so .

, that is , option (c).

The Wheatstone bridge does not alter the gauge's own . It only converts this small change into an output voltage. Option (a) is just the strain, ignoring the gauge factor.

Where this shows up in industry

Strain-gauge bridges instrument load cells, rocket-motor thrust stands, and structural tests of spacecraft panels, where parts-per-million changes in resistance are amplified and read out.

ISRO 2025 · Electronics Set A · Q.64Part A · 1 mark · -0.33 if wrongElectronic devices and VLSI

Condition that maximizes diffusion current in a semiconductor

Which of the following conditions will maximize the diffusion current in a semiconductor?
  1. (a)Uniform doping profile
  2. (b)High electric field
  3. (c)Steep concentration gradient
  4. (d)Zero temperature gradient

Answer: (c) Steep concentration gradient Official final key: (c)

Diffusion current density is driven by the carrier concentration gradient: (and ).

  • (a) Uniform doping: , so no diffusion current.
  • (b) A high electric field drives drift current, a different mechanism.
  • (c) A steep gradient makes large. For an exponential profile the gradient is at the surface, so the diffusion current grows as shrinks, against zero for a uniform profile.
  • (d) A zero temperature gradient has no role in this expression.

Steep concentration gradient, option (c).

Where this shows up in industry

Diffusion current is what carries charge across the base of a BJT and across a p-n junction, so doping profiles in transistors and solar cells are engineered to set the gradient.

ISRO 2025 · Electronics Set A · Q.65Part A · 1 mark · -0.33 if wrongNetworks

Power factor of a 10 ohm resistor in series with a 10 ohm inductive reactance

In an AC circuit, a resistor of 10 is in series with an inductor of reactance 10 . What is the power factor of the circuit?
  1. (a)0.5 lagging
  2. (b)0.707 lagging
  3. (c)1.0 (unity)
  4. (d)0.866 leading

Answer: (b) 0.707 lagging Official final key: (b)

In a series circuit the impedance is , so .

The power factor is , with .

An inductor makes the current lag the voltage, so the power factor is lagging. lagging, option (b).

Option (d) has the right kind of number for a 30 degree angle but the wrong value and the wrong sign: a leading power factor needs a capacitive circuit.

Where this shows up in industry

Power factor sets how much extra current a motor or transformer winding draws for the same real power, which is why lagging loads on satellite ground-station supplies and factory feeders are corrected with capacitors.

ISRO 2025 · Electronics Set A · Q.66Part A · 1 mark · -0.33 if wrongElectronic devices and VLSI

NMOS and PMOS state in the transition region of a CMOS inverter

In a CMOS inverter operating in the transition region, what best describes the operation of NMOS and PMOS transistors?
  1. (a)Both are in cutoff region
  2. (b)Only PMOS conducts
  3. (c)Both are conducting
  4. (d)Only NMOS conducts

Answer: (c) Both are conducting Official final key: (c)

On the voltage transfer curve the output swings from high to low over a narrow input range around . That is the transition region.

Take and as a check. At the NMOS has and the PMOS has . Both gate overdrives are positive, so both transistors are on, and both are in saturation, which is why the gain is so high there.

Only at the two ends of the curve does one device turn off: low input turns the NMOS off, high input turns the PMOS off. Both conduct, option (c). This is also why a slow input edge makes a short-circuit current spike flow from supply to ground.

Where this shows up in industry

This overlap of conduction is the origin of short-circuit (crowbar) power in digital ASICs and radiation-tolerant logic, and designers limit it by keeping input edges fast.

ISRO 2025 · Electronics Set A · Q.67Part A · 1 mark · -0.33 if wrongAnalog circuits

LVDT core displacement for 2 mV/mm/V sensitivity, 5 V excitation and 30 mV output

An LVDT (Linear Variable Differential Transformer) has a sensitivity of 2 mV/mm/V (output per mm of displacement per volt of excitation). If it is excited with 5 V AC and produces an output of 30 mV, what is the core displacement?
  1. (a)1 mm
  2. (b)2 mm
  3. (c)3 mm
  4. (d)None of the above

Answer: (c) 3 mm Official final key: (c)

Sensitivity is quoted per volt of excitation, so at 5 V the output per millimetre is .

, option (c). Forgetting the excitation voltage gives , which is not an option, so the 5 V must be used.

Where this shows up in industry

LVDTs measure actuator and valve positions in aerospace hydraulics and test rigs because the core never touches the coils, so there is no wear and they survive vibration.

ISRO 2025 · Electronics Set A · Q.68Part A · 1 mark · -0.33 if wrongElectronic devices and VLSI

Fermi level expression for an N-type semiconductor

In an N-type semiconductor, the Fermi level equals :
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (a) Official final key: (a)

For a non-degenerate N-type material the electron density is and, with full ionisation, .

Equating and solving: .

Numerical check with silicon-like values (, , , ): option (a) puts at above , which is below and above mid-gap (), as N-type requires.

Option (b) gives , above the conduction band edge. Option (c) gives and option (d) a negative value, so these describe levels near or below the valence band. , option (a).

Where this shows up in industry

This relation sets the threshold voltage and contact barriers of every MOSFET and diode, and process engineers use it to turn a measured doping level into a band diagram.

ISRO 2025 · Electronics Set A · Q.69Part A · 1 mark · -0.33 if wrongAnalog circuits

Third harmonic of a single-phase square-wave inverter when the fundamental is V

In a single-phase full-bridge inverter with square wave output, what is the amplitude of the third harmonic component if the fundamental amplitude is V?
  1. (a)V/3
  2. (b)V/5
  3. (c)V/9
  4. (d)V/7

Answer: (a) V/3 Official final key: (a)

A square wave of amplitude has the Fourier series

Only odd harmonics exist and the th has amplitude .

Fundamental: . Third harmonic: .

Third harmonic , option (a). Option (c), , would be the answer if the amplitudes fell as , as for a triangular wave.

Where this shows up in industry

The large low-order harmonics of a square-wave inverter are why spacecraft and UPS inverters use PWM, stepped or multilevel output plus filters.

ISRO 2025 · Electronics Set A · Q.70Part A · 1 mark · -0.33 if wrongElectronic devices and VLSI

Forbidden band gap of germanium at 0 K

Select the value closest to the forbidden band in Germanium at 0 K :
  1. (a)0.78 eV
  2. (b)1.00 eV
  3. (c)0.01 eV
  4. (d)1.21 eV

Answer: (a) 0.78 eV Official final key: (a)

Germanium has an indirect gap that widens slightly as temperature falls. Textbook values are about at 300 K and about at 0 K, depending on the source. The commonly quoted 0 K figure is .

A Varshni-type fit, , with gives at 300 K, matching the usual room-temperature value.

Of the options, is close to silicon's 0 K gap (about 1.17 to 1.21 eV depending on the source) ( at 300 K is its room-temperature value) and and are far off. The closest is , option (a).

Where this shows up in industry

Germanium's small gap makes it useful for infrared detectors and for the germanium layers in high-speed SiGe transistors, but also gives it large leakage at room temperature.

ISRO 2025 · Electronics Set A · Q.71Part A · 1 mark · -0.33 if wrongSignals and systems

Impulse response from H(e^jw) = 1/(1 - 0.5 e^-jw)

If a discrete-time LTI system has a frequency response , what is its impulse response ?
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (a) Official final key: (a)

Multiply out: . In the time domain this is .

With and a causal system: , , , , and so on. That is .

Equivalently, the geometric series converges because .

, option (a). Option (b) is the same shape delayed by one sample (it would carry an extra ). Option (d) is the impulse response of the reciprocal, FIR filter .

Where this shows up in industry

First-order recursive filters of this kind smooth sensor and telemetry data in embedded firmware at almost no cost in memory or arithmetic.

ISRO 2025 · Electronics Set A · Q.72Part A · 1 mark · -0.33 if wrongElectronic devices and VLSI

Definition of pinch-off voltage in an FET

Pinch-off voltage in an FET is :
  1. (a)The gate-to-source voltage that gives zero drain current
  2. (b)The drain voltage that gives zero drain current
  3. (c)The gate source voltage that gives unity drain current
  4. (d)The drain voltage that gives infinite drain current

Answer: (a) The gate-to-source voltage that gives zero drain current Official final key: (a)

In a JFET the gate-source voltage controls how wide the conducting channel is. At the depletion regions from both sides meet and close the channel, so .

The square-law model shows this: with and , at and at .

So pinch-off voltage is a gate-source voltage, and it gives zero (not unity, not infinite) drain current. Option (a). Note that the word pinch-off also names a drain-source effect (saturation begins at ), but the quantity called the pinch-off voltage is itself.

Where this shows up in industry

JFETs are used as low-noise input stages for sensors and radio front ends, and the pinch-off voltage is the first datasheet number used to set their bias point.

ISRO 2025 · Electronics Set A · Q.73Part A · 1 mark · -0.33 if wrongControl systems

Nature of the poles of H(s) = (s + 1)/(s^2 + 2s + 2)

Consider the system with transfer function . Which of the following best describes the nature of its poles?
  1. (a)Real and equal
  2. (b)Real and distinct
  3. (c)Complex conjugates with negative real parts
  4. (d)Purely imaginary

Answer: (c) Complex conjugates with negative real parts Official final key: (c)

Poles are the roots of the denominator: .

Discriminant: , so the roots are complex: .

The real part is , which is negative (the system is stable), and the imaginary part is non-zero. The zero at is not a pole and does not affect this. The damping ratio is .

Complex conjugate poles with negative real parts, option (c). Purely imaginary poles (option d) would need no term in the denominator.

Where this shows up in industry

Pole location tells a control engineer how fast a loop settles and how much it rings, and a damping ratio near 0.7 is the usual design target for attitude control loops.

ISRO 2025 · Electronics Set A · Q.74Part A · 1 mark · -0.33 if wrongAnalog circuits

What the output of a Schmitt trigger depends on

The output of a Schmitt trigger depends on :
  1. (a)Only input value
  2. (b)Clock transitions
  3. (c)Hysteresis in threshold voltages
  4. (d)Fan-in of the gate

Answer: (c) Hysteresis in threshold voltages Official final key: (c)

A Schmitt trigger has two thresholds: an upper one that the input must exceed to switch the output high, and a lower one that it must drop below to switch it low. Between the two the output holds its previous state.

Example with and : an input of gives output 0 if the input arrived from below and output 1 if it arrived from above. So the output is not a function of the input value alone (option a is wrong).

It has no clock (option b), and fan-in is a loading rating of the logic family (option d). The output depends on the hysteresis between the threshold voltages, option (c). This is what lets it clean up slow or noisy edges.

Where this shows up in industry

Schmitt-trigger inputs clean up noisy sensor, switch and long-cable signals on microcontroller and FPGA pins so that a slowly changing or noisy edge does not cause multiple false counts.

ISRO 2025 · Electronics Set A · Q.75Part A · 1 mark · -0.33 if wrongSignals and systems

Which system is not causal

Which of the following systems is “not” causal?
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (c) Official final key: (c)

A discrete-time LTI system is causal if and only if for all , because the output may not depend on future inputs.

  • (a) is non-zero only at : causal.
  • (b) is zero for : causal (an accumulator).
  • (d) is zero for : causal.
  • (c) is non-zero at , where . The output uses the next input sample, so it is not causal.

Option (c) is the non-causal system.

Where this shows up in industry

Real-time filters in telemetry and radar processors must be causal, and non-causal designs are used only offline, where the whole recording is available, or after adding a fixed delay.

ISRO 2025 · Electronics Set A · Q.76Part A · 1 mark · -0.33 if wrongDigital circuits and microprocessors

Size of a memory system made of four 4 x 4 chips on a common address bus

Four memory chips of size have their address bus connected together. This system will be of size
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (c) Official final key: (c)

A chip holds 4 words of 4 bits: two address lines and four data lines.

When all four chips share the same address bus, every chip responds to the same address at the same time. The number of words therefore stays at 4, and the four 4-bit outputs sit side by side to form one wider word of bits.

Size: , option (c). (Word-capacity expansion, giving , needs the chips to be selected by extra address lines through a decoder instead.)

Where this shows up in industry

Widening a memory by paralleling chips on one address bus is how 32-bit and 64-bit wide memory is built from narrow devices on board-level designs.

ISRO 2025 · Electronics Set A · Q.77Part A · 1 mark · -0.33 if wrongAnalog circuits

Voltmeter with the least loading effect on a 100 kOhm source

Which of the following voltmeters will have the least loading effect on a source?
  1. (a), 10 V range
  2. (b), 10 V range
  3. (c) digital voltmeter
  4. (d), 5 V range

Answer: (c) digital voltmeter Official final key: (c)

The meter resistance forms a divider with the source resistance, so the reading is . The larger is, the smaller the loading error. For analogue meters .

  • (a) : reads of the true value.
  • (b) : reads of the true value.
  • (d) : reads of the true value.
  • (c) : reads of the true value.

The highest input resistance, and so the least loading, is the digital voltmeter, option (c).

Where this shows up in industry

High-impedance measurement matters when probing sensor outputs and bias networks; a meter that is too low in resistance changes the very voltage it is meant to read.

ISRO 2025 · Electronics Set A · Q.78Part A · 1 mark · -0.33 if wrongDigital circuits and microprocessors

What limits the maximum clock frequency of a 4-bit JK ripple counter

In a 4-bit ripple counter using JK flip-flops, the maximum frequency of input clock is limited due to :
  1. (a)Propagation delay
  2. (b)Setup time
  3. (c)Hold time
  4. (d)Fan-in

Answer: (a) Propagation delay Official final key: (a)

In a ripple (asynchronous) counter each flip-flop is clocked by the output of the one before it, so a change ripples through the chain one stage at a time. The last output settles only after .

With and an assumed per stage the counter needs to settle, so the clock cannot exceed about , against for one flip-flop alone.

Setup and hold times are requirements on data inputs relative to a clock edge, and in this counter J and K are tied high. Fan-in is a gate input count. Cumulative propagation delay is the limit, option (a).

Where this shows up in industry

This delay accumulation is why fast counters and frequency dividers inside timing and PLL chains use synchronous designs instead of ripple chains.

ISRO 2025 · Electronics Set A · Q.79Part A · 1 mark · -0.33 if wrongNetworks

Resonant frequency, bandwidth and Q of a parallel RLC with 1.25 MOhm source resistance

In the below circuit, the value of , , and Q are respectively :
1.25 MΩ4 pF10 mH5 MΩ+-vi
  1. (a)25 Mrad/s, 250 Krad/s, 100
  2. (b)5 Mrad/s, 250 Krad/s, 20
  3. (c)5 Mrad/s, 25 Krad/s, 200
  4. (d)None of the above

Answer: (b) 5 Mrad/s, 250 Krad/s, 20 Official final key: (b)

The figure shows in series with the source, then , and in parallel. Looking back from the - pair, the source is replaced by its Thevenin resistance, so the and appear in parallel: .

Resonant frequency: .

Quality factor of a parallel circuit: .

Bandwidth: .

, , , option (b). Using alone would give , which is the trap in option (a) (that option also has the wrong ).

Where this shows up in industry

Parallel tuned circuits like this set the centre frequency and selectivity of IF filters and oscillator tanks, and the loading by source and load resistance is what limits the achievable Q in practice.

ISRO 2025 · Electronics Set A · Q.80Part A · 1 mark · -0.33 if wrongNetworks

Inductor voltage at t = 0+ for a unit step on a series RL circuit, R = 2 ohm, L = 2 H

A unit step voltage is applied at to a series RL circuit with , . What is the voltage across the inductor at ?
R2 ΩL2 Hstep
  1. (a)0 V
  2. (b)1 V
  3. (c)2 V
  4. (d)Infinity

Answer: (b) 1 V Official final key: (b)

An inductor does not allow its current to change instantly, so .

With zero current there is no drop across the resistor: . By KVL the whole step appears across the inductor: .

The full response is and (time constant ), which equals at and decays to zero.

, option (b). Option (a) would be the voltage across the resistor at that instant, and option (c), 2 V, is not reached because the step is only 1 V.

Where this shows up in industry

Knowing that an inductor opposes an instant current change explains the voltage spike across relay and solenoid coils when switched, and why flyback diodes and snubbers are fitted on spacecraft valve drivers.

From ISRO prep to a core electronics career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.