ISRO Scientist/Engineer Electronics 2025 paper: Part A, questions 41 to 60, solved

Questions 41 to 60 of the ISRO Scientist/Engineer 'SC' Electronics written test of 26 Oct 2025 (Set A): 20 questions, each solved by Skill-Lync and checked against ISRO's final answer key.

Question paper and answer keys published by ISRO's Centralised Recruitment Board; solutions by Skill-Lync · Updated 18 Nov 2026 · 20 of 80 questions on this page

ISRO 2025 · Electronics Set A · Q.41Part A · 1 mark · -0.33 if wrongDigital circuits and microprocessors

Which condition reduces the MTBF due to metastability

Which of the following conditions reduces the Mean Time Between Failures (MTBF) due to metastability?
  1. (a)Decreasing flip-flop setup time
  2. (b)Increasing the metastability resolution time
  3. (c)Increasing clock frequency and data arrival rate
  4. (d)All of the above

Answer: (c) Increasing clock frequency and data arrival rate Official final key: (c)

The synchroniser failure rate model is

where is the time allowed for a metastable output to resolve, and are flip-flop constants, is the clock frequency and the data arrival rate. A failure needs data to land in the vulnerable window, so more clock edges and more data edges mean more chances.

  • (c) Doubling both and divides the MTBF by 4. This lowers MTBF.
  • (a) A smaller setup time leaves more of the clock period for resolution (larger ), so MTBF rises.
  • (b) A longer resolution time (more time allowed for the output to settle) raises MTBF exponentially.

Only (c) lowers MTBF, so option (c), and (d) is wrong.

Where this shows up in industry

Designers add a two-flip-flop synchroniser (or more stages) at every clock-domain crossing, such as between a sensor clock and a processor clock on a spacecraft, to push the MTBF to years or centuries.

ISRO 2025 · Electronics Set A · Q.42Part A · 1 mark · -0.33 if wrongSignals and systems

Fourier transform of x(t) = rect(t/2), a rectangular pulse of width 2

Let , where is the rectangular pulse of width 2 centered at , i.e., for and 0 otherwise. What is the Fourier Transform of ?
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (a) Official final key: (a)

Integrate over the pulse:

With (the convention in which the options are written), this is . Check at : is the pulse area, , and . Option (a).

In general a pulse of width and height 1 has . Here . The first zero is at , as there. (If the normalised sinc were meant, the answer would be written , which is not offered.)

Where this shows up in industry

The rectangular pulse and its sinc spectrum explain why a gated or sampled signal leaks energy into sidelobes, which matters when windowing data in spectrum analysers and receivers.

ISRO 2025 · Electronics Set A · Q.43Part A · 1 mark · -0.33 if wrongAnalog circuits

Biasing modes of ideal diodes D1, D2, D3 in a resistor-diode network

For a given diode circuit as shown in figure what will be the biasing modes of diodes D1, D2, D3? (FB: Forward Bias, RB: Reverse Bias) Assume diodes are ideal.
10VD33 kohm7 kohm2.5 kohm−5VD2D10V+5V
  1. (a)D1-FB, D2-FB, D3-FB
  2. (b)D1-FB, D2-RB, D3-FB
  3. (c)D1-FB, D2-FB, D3-RB
  4. (d)D1-FB, D2-RB, D3-RB

Answer: (b) D1-FB, D2-RB, D3-FB Official final key: (b)

Ideal diodes: a forward diode is a short, a reverse one is open. Guess and check.

Guess D2 reverse, D1 and D3 forward. Then 10 V pushes current through into D1's node, which D1 holds at 0 V: that current is . The first node is at .

Checks: D2 has at its anode and at its cathode, so it is reverse biased. The 2.5 k resistor to draws from the second node, of which 1 mA comes from the 7 k and the other 1 mA from D1: forward, positive current. D3 carries 1 mA forward.

Trying D2 forward instead would clamp the first node to 5 V and give a negative current in D2, which is impossible. Working through the other combinations, only one is self-consistent: D1-FB, D2-RB, D3-FB, option (b).

Where this shows up in industry

Diode clamp and OR-ing networks like this are used to steer current in power-supply redundancy circuits, where a diode must be reverse biased for the standby source and forward for the active one.

ISRO 2025 · Electronics Set A · Q.44Part A · 1 mark · -0.33 if wrongControl systems

Phase margin and gain margin from a frequency response table (excluded from evaluation)

Frequency response of a system is given in the following table :
Frequency (rad/s)Gain (dB)Phase (deg)
18−50
101−155
1000.25−180
10000.1−235
The Phase margin and Gain margin respectively are
  1. (a)4, 25
  2. (b)25, 4
  3. (c)25, 0.25
  4. (d)0.25, 25

Answer: (b) 25, 4 (excluded by ISRO from evaluation) Excluded from evaluation by ISRO

ISRO excluded this question from evaluation for administrative reasons. The earlier keys (October and December 2025) gave (b). The most likely reason is the table itself: the column is headed 'Gain (dB)' but the numbers only make sense as plain magnitudes.

Reading the gain column as magnitudes (it falls smoothly from 8 to 0.1, and the answers 25 and 4 rely on it):

  • Phase margin: find the gain crossover, where . That is at , where the phase is . .
  • Gain margin: find the phase crossover, where the phase is . That is at , where . (about ).

This gives 25, 4, option (b).

Reading the column literally as decibels: all four gains (8, 1, 0.25, 0.1 dB) are above 0 dB, so the table never reaches a gain crossover and the phase margin cannot be read from it. At the phase crossover the gain is , a gain margin of , meaning the loop would be unstable. No option fits that reading, so the question is only answerable as (b) if the 'dB' label is a printing mistake.

Where this shows up in industry

Gain and phase margin read off measured Bode data decide whether a control loop, such as a reaction wheel or antenna pointing servo, has enough safety margin against instability.

ISRO 2025 · Electronics Set A · Q.45Part A · 1 mark · -0.33 if wrongNetworks

Synthesis of the driving-point impedance Z(s) = (s^2 + 3s + 2) / (s(s + 2))

The driving-point impedance of a network is given by: . Which of the following statements is correct regarding the synthesis of this network?
  1. (a)The function is not realizable using passive elements only
  2. (b)The function can be realized using L and C elements only
  3. (c)The function can be realized using passive elements only
  4. (d)The function is not positive real and cannot be synthesized

Answer: (c) The function can be realized using passive elements only Official final key: (c)

Factor the numerator: . The cancels:

This is the impedance of a resistor in series with a capacitor. It is positive real: its only pole is a simple one at with positive residue 1, and for all . So it is realizable with passive elements (R and C), which makes option (c) correct.

(a) and (d) are false because it is positive real and has an explicit RC circuit. (b) is false: an L and C only (lossless) function must have , and here the real part is 1, the resistor.

Where this shows up in industry

Driving-point synthesis is how filters, matching networks and equalisers are turned from a target impedance into real R, L and C values.

ISRO 2025 · Electronics Set A · Q.46Part A · 1 mark · -0.33 if wrongAnalog circuits

OPAMP input signs for negative feedback around an NMOS with a 0.5 mA source

In the below figure, determine the signs on the OPAMP terminals A and B for negative feedback operation and gate potential of the transistor for and . ,
Vdd0.5mAVrefAB3V
  1. (a)Terminal A is positive. Terminal B is negative
  2. (b)Terminal A is negative. Terminal B is positive
  3. (c)Both of above
  4. (d)None of the above

Answer: (a) Terminal A is positive. Terminal B is negative Official final key: (a)

In the figure the op-amp output drives the transistor's source, the gate is held at the labelled 3 V, and the drain node is both the current source's output and input B.

Operating point: with , gives , so and the source sits at . The loop forces the drain to , so and the transistor is in saturation.

Sign of the feedback: if the op-amp output (the source voltage) rises, falls, the transistor sinks less than the 0.5 mA supplied, and the drain voltage rises. The drain goes to B, so a rise at B must pull the output down: B must be the inverting input (negative) and A the non-inverting input (positive).

With the opposite polarity, a rise at the drain pushes the op-amp output (the source) up, so falls, the transistor sinks less current and the drain rises further: positive feedback, and the loop runs away from Vref.

A positive, B negative, option (a). The question's figure shows the gate at 3 V and the op-amp output at the source (about 1.3 V).

Where this shows up in industry

A regulator loop that sets a transistor's current from a reference, with the op-amp forcing the drain to Vref, is the basis of cascode bias generators and low-dropout regulators.

ISRO 2025 · Electronics Set A · Q.47Part A · 1 mark · -0.33 if wrongNetworks

Signal flow graph of a two-mesh resistor network with source v1 and output vo

The network of a system is shown below. Signal flow graph for the system is
+−i1i2v1R1v2R2v3R3R4+−vo
  1. (a)1R3R2R41v1i1v2i2v3v3−1/R1−R3−1/R2
  2. (b)1/R1R31/R2R41v1i1v2i2v3v3−1/R1−R3−1/R2
  3. (c)1R3R2R41v1i1v2i2v3v3−1/R1−1/R3−1/R2
  4. (d)1/R1R31/R2R41v1i1v2i2v3v3−1/R1−1/R3−R2

Answer: (b) Graph (b): forward gains ; back branches Official final key: (b)

Write one equation per variable: each current is a resistor voltage divided by R, each voltage is R times a current.

  • : branch with gain , branch with gain .
  • : branch with gain , branch with gain .
  • : branch with gain , branch with gain .
  • : branch with gain , and with gain 1.

That is graph (b): forward gains and back branches .

Dimension check: a branch from a current to a voltage must have the unit of a resistance, and a branch from a voltage to a current that of a conductance. Graphs (a) and (c) give the gain , graphs (c) and (d) give the gain , and graph (d) gives the gain , so they fail. Option (b).

Where this shows up in industry

Signal flow graphs and Mason's gain formula are used to reduce block diagrams and electrical networks to transfer functions without redoing the algebra each time.

ISRO 2025 · Electronics Set A · Q.48Part A · 1 mark · -0.33 if wrongElectromagnetics, microwaves and antennas

Directivity of an antenna: Rr = 63 ohm, Rloss = 7 ohm, power gain 16

The radiation resistance of an antenna is 63 ohms and the loss resistance is 7 ohms. If antenna has power gain of 16, then directivity is
  1. (a)48.26 dB
  2. (b)12.5 dB
  3. (c)17.77 dB
  4. (d)24.7 dB

Answer: (b) 12.5 dB Official final key: (b)

Radiation efficiency is the share of the input power that is radiated:

Power gain is directivity times efficiency, , so

In decibels: , so , option (b).

Trap: option (c) is the directivity as a plain ratio (17.77) with a dB label attached; the power gain of 16 is also a ratio, and decibels need .

Where this shows up in industry

Radiation efficiency shows how much of a transmitter's power an antenna actually radiates; small antennas on satellites and handsets often have low efficiency because loss resistance is comparable to radiation resistance.

ISRO 2025 · Electronics Set A · Q.49Part A · 1 mark · -0.33 if wrongDigital circuits and microprocessors

Output function Y of an NMOS bridge network with load transistor Q1 (inputs A to E)

Determine the output function Y from the following circuit :
VDDQ1OutputABCDE
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: Excluded by ISRO. The pull-down network is , option (b); the output is its complement. Excluded from evaluation by ISRO

ISRO excluded this question from evaluation “for administrative reasons”, so it carries no marks and no negative marking. Its provisional key (Oct 2025) gave (b).

The pull-down network is a bridge. Transistor A joins the output node to the left middle node, B joins that node to ground, C joins the output node to the right middle node, D joins that node to ground, and E joins the two middle nodes. The output is pulled to ground whenever there is a conducting path from the output node to ground. The four paths are:

  • A then B:
  • C then D:
  • A, E, then D:
  • C, E, then B:

So the pull-down network conducts when . This is exactly option (b), and checking all 32 input combinations confirms that (a), (c) and (d) each miss at least one path.

The catch is that Q1 is a load (pull-up), so the output is high only when no path conducts. The logic level at the output is therefore the complement, , and no printed option carries that bar. Option (b) is the expression for the pull-down network, not for the output voltage as literally written, which is a likely reason the question was dropped.

Where this shows up in industry

Bridge-type pull-down networks like this appear in ratioed NMOS and dynamic logic, where one shared transistor cuts the transistor count versus a plain sum-of-products implementation.

ISRO 2025 · Electronics Set A · Q.50Part A · 1 mark · -0.33 if wrongControl systems

True statements about a proportional plus derivative (PD) controller

Consider the following statements : A proportional plus derivative controller
  1. Has high sensitivity
  2. Improves the steady state accuracy
  3. Increases the stability of the system
Which of the following statements are correct?
  1. (a)(i), (ii) and (iii)
  2. (b)(i) and (ii)
  3. (c)(ii) and (iii)
  4. (d)(i) and (iii)

Answer: (d) (i) and (iii) Official final key: (d)

A PD controller is . Check each statement.

(i) High sensitivity: true. Its gain rises with frequency. For at the gain is 5.10 times , so it reacts strongly to fast changes (and to noise).

(ii) Improves steady-state accuracy: false. At the derivative term vanishes, , so the error constants and the steady-state error do not change. Example with and : with or without the derivative term.

(iii) Increases stability: true. It adds phase lead and damping. For with and the characteristic equation is , so rises from 0.25 () to 0.75 ().

Only (i) and (iii) are correct, option (d). The common trap is to credit PD with better accuracy; that is the job of an integral term (PI or PID).

Where this shows up in industry

PD (or PID with a filtered derivative) loops are standard in satellite attitude control and in motor and servo drives, where the derivative term adds damping against overshoot.

ISRO 2025 · Electronics Set A · Q.51Part A · 1 mark · -0.33 if wrongElectromagnetics, microwaves and antennas

Boundary conditions for H at the interface of two magnetic materials (mu1, mu2)

A boundary separates two magnetic materials of permeability and . The magnetic field vector in is with a normal component and tangential component while that in is with a normal component and a tangential component . Then the derived condition would be
  1. (a) and
  2. (b) and
  3. (c) and
  4. (d) , and

Answer: (b) and Official final key: (b)

At a boundary with no surface current, Maxwell's equations give two conditions:

  • gives continuous tangential : .
  • gives continuous normal : , that is .

The full vectors and are not equal unless , because the normal components differ. Check with numbers: , , , . Then and , so but . This rules out (a), (c) and (d).

The correct pair is option (b).

Where this shows up in industry

These two conditions are used to compute the field in magnetic shields and in the flux paths of transformer and motor cores, where high-permeability iron makes field lines leave the surface almost normally.

ISRO 2025 · Electronics Set A · Q.52Part A · 1 mark · -0.33 if wrongAnalog circuits

Base-collector voltage VBC of a common base circuit with RE = 4 kohm and RC = 2.2 kohm

What is the value of base collector voltage for the given common base circuit shown in figure? For the transistor, assume .
RE = 4 kohmVEB = 0.7 V+-9VVEEVBCRC 2.2 kohm-+VCC9V
  1. (a)7.47 V
  2. (b)8.43 V
  3. (c)4.47 V
  4. (d)0.47 V

Answer: (c) 4.47 V Official final key: (c)

The transistor is a pnp type: the 9 V battery pushes current into the emitter, and the base is at the circuit's ground (the bottom wire).

Emitter current: .

Collector current: .

Voltage across : . The far end of sits at (the negative terminal of is on top), so the collector voltage is .

With the base at 0 V: , so , option (c). A positive for a pnp device means the collector-base junction is reverse biased, as it should be in the active region.

Where this shows up in industry

Common-base stages are used where wide bandwidth and low input resistance matter, for example in RF and microwave amplifier stages and cascode front ends of receivers.

ISRO 2025 · Electronics Set A · Q.53Part A · 1 mark · -0.33 if wrongControl systems

Sensitivity of steady-state step error to u in a loop with (s+u) feedback

Consider the system shown below. The sensitivity of the steady state error for step input is
R(s)+-Ks(s+1)(s+4)C(s)(s+u)
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (d) Official final key: (d)

The feedback is , not unity, so the error is taken as (the output minus the wanted value). The closed loop is with .

For a unit step, . The pole of at the origin makes as , so .

Sensitivity of to : . Here , so

Check with : and the sensitivity is . Option (d).

Note the key assumes this definition of error. With unity-feedback error the steady-state error would be zero for any and the question would have no answer.

Where this shows up in industry

Sensitivity analysis like this tells control engineers how much a drifting sensor or feedback gain (here the factor ) changes the final accuracy of a loop, which is why sensor scale factors are calibrated carefully.

ISRO 2025 · Electronics Set A · Q.54Part A · 1 mark · -0.33 if wrongElectromagnetics, microwaves and antennas

Physical meaning of loss tangent tan delta tending to infinity

Consider a lossy dielectric with complex permittivity . The loss tangent is defined as . What does physically imply?
  1. (a)The medium behaves like a perfect conductor
  2. (b)The medium behaves like a lossless dielectric
  3. (c)The medium behaves like a perfect insulator
  4. (d)The displacement current dominates conduction current

Answer: (a) The medium behaves like a perfect conductor Official final key: (a)

Write the loss tangent in terms of the two currents in the medium: .

If , conduction current dominates completely. That is the behaviour of a conductor, and in the limit a perfect conductor. For example, with , and the ratio is already about .

  • (b) and (c): a lossless dielectric or perfect insulator has , so , the opposite limit.
  • (d): displacement current dominating means , again the opposite.

Option (a).

Where this shows up in industry

Loss tangent is the figure of merit for PCB laminates, radome materials and microwave substrates: low values keep signal loss small, while very high values (metals, wet soil, sea water) act as conductors and reflect or absorb radio waves.

ISRO 2025 · Electronics Set A · Q.55Part A · 1 mark · -0.33 if wrongAnalog circuits

Branch currents I1, I2, I3 in an ideal op-amp circuit with a 1 V input

In the following amplifier circuit, the OPAMP is ideal. Find the values of , , :
1V-10 kohmI1-+10 kohmI21 kohmvo100 ohmI3
  1. (a), ,
  2. (b), ,
  3. (c), ,
  4. (d), ,

Answer: (a) , , Official final key: (a)

The non-inverting input is grounded, so by the virtual short the inverting input is also at 0 V. An ideal op-amp draws no input current.

. All of it must flow on through the feedback 10 kΩ, so .

The voltage at the node after the feedback resistor is . The 100 Ω resistor goes from that node to ground, so (upward, from ground into the node, as the arrow shows).

Check: the 1 kΩ resistor then carries , giving .

, , , option (a).

Where this shows up in industry

The T-network feedback shown is used in inverting amplifiers that need a high gain without a very large feedback resistor, for example in transimpedance and sensor-signal stages.

ISRO 2025 · Electronics Set A · Q.56Part A · 1 mark · -0.33 if wrongControl systems

Transfer function from a Bode magnitude plot with slopes -20, -40 and -60 dB/decade

Consider the following Bode plot, the transfer function of this system shall be
dBω6040011020-20dB/decade-40dB/decade-60dB/decade
  1. (a)
  2. (b)
  3. (c)
  4. (d)

Answer: (d) Official final key: (d)

Read the slopes. The plot starts at : one pole at the origin, . At the slope becomes : a pole at . At it becomes : a pole at . The corner values 1 and 20 are what the four options use.

Gain: at the plot is at 40 dB, which is a magnitude of 100. With , gives (asymptotically), so . Check at : , that is 0 dB, as drawn.

Why (d) and not (a) or (b): a Bode magnitude plot cannot tell from , because . So (a), (b) and (d) all have the same magnitude curve. They differ in phase: (a) and (b) have poles in the right half plane, which is an unstable system. The standard reading of such a plot is the minimum-phase one with all poles in the left half plane. Option (c) has the wrong gain (at it gives , about 34 dB) and also a right-half-plane pole.

, option (d).

Where this shows up in industry

Fitting a transfer function to a measured Bode plot is how loop gains of power supplies, attitude control loops and amplifier compensation are identified from frequency-response tests.

ISRO 2025 · Electronics Set A · Q.57Part A · 1 mark · -0.33 if wrongCommunications

Channel capacity of a 3 kHz channel with SNR of 30 dB

A communication channel has a bandwidth of 3 kHz and Signal-to-Noise Ratio (SNR) of 30 dB. What is the channel capacity?
  1. (a)~30 kbps
  2. (b)~20 kbps
  3. (c)~2.1 kbps
  4. (d)~3.3 kbps

Answer: (a) ~30 kbps Official final key: (a)

Shannon-Hartley theorem: , with SNR as a plain ratio, not in dB.

.

, so , option (a).

A quick check: because , so .

Where this shows up in industry

Shannon capacity is the upper bound that link budgets for satellite downlinks and telephone-grade lines are measured against; real modems and modulation-coding schemes reach within a dB or two of it.

ISRO 2025 · Electronics Set A · Q.58Part A · 1 mark · -0.33 if wrongAnalog circuits

Input voltage Vi at which the LED turns on in an op-amp comparator (6 V reference)

In the circuit given below, LED will be ON (OPAMP and LED to be considered as ideal) when is:
+12V10 kohm10 kohm-+viR
  1. (a)Less than 6 V
  2. (b)More than 6 V
  3. (c)Less than 12 V
  4. (d)More than 12 V

Answer: (b) More than 6 V Official final key: (b)

The op-amp has no feedback, so it works as a comparator. The two equal 10 kΩ resistors form a divider that holds the inverting input at .

The signal is on the non-inverting input. When , and the output goes to its positive limit, which drives current through R into the LED, so it lights. When the output goes low and the LED is off.

The LED is on for , option (b). Option (d) is wrong because the LED already lights between 6 V and 12 V; option (c) would turn it on for low voltages, the reverse of the true behaviour.

Where this shows up in industry

Window and threshold comparators like this drive over-voltage and under-voltage indicators and flags in power-supply monitors and battery-management circuits of satellites and ground equipment.

ISRO 2025 · Electronics Set A · Q.59Part A · 1 mark · -0.33 if wrongAnalog circuits

Feedback topology of an op-amp amplifier with an emitter follower output stage

Consider the circuit shown below. This amplifier circuit will be
1 kohmvin+-1 kohm+10Vvo10 kohm0.2 mA
  1. (a)Series-Series
  2. (b)Shunt-Series
  3. (c)Series-Shunt
  4. (d)Shunt-Shunt

Answer: (c) Series-Shunt Official final key: (c)

The feedback network is the 10 kΩ and 1 kΩ divider.

  • Mixing at the input: the input signal goes to the non-inverting input and the feedback voltage (from the divider) is applied at the inverting input. The two voltages are subtracted in the input loop, so the feedback is connected in series with the source.
  • Sampling at the output: the divider is connected across the output node and samples the output voltage, which is shunt (parallel) sampling.

This is the series-shunt (voltage-series) topology, which stabilises the voltage gain: for an ideal op-amp , so . Option (c).

The BJT stage is just an emitter follower with a 0.2 mA current-source load inside the loop. It does not change the topology.

Where this shows up in industry

Series-shunt (non-inverting voltage amplifier) feedback is the most common way to set a precise voltage gain and a high input and low output resistance in instrumentation and buffer amplifiers.

ISRO 2025 · Electronics Set A · Q.60Part A · 1 mark · -0.33 if wrongSignals and systems

Nyquist rate of x(t) = 5 cos(100 pi t) + 2 sin(200 pi t)

What is the Nyquist rate for a continuous time signal ?
  1. (a)100 Hz
  2. (b)200 Hz
  3. (c)400 Hz
  4. (d)50 Hz

Answer: (b) 200 Hz Official final key: (b)

Convert each angular frequency to hertz using .

  • :
  • :

The highest frequency present is . The Nyquist rate is twice that, , so option (b).

Trap: 100 Hz (option a) is the highest frequency, and 50 Hz is the lower tone; neither is a sampling rate. Option (c) comes from forgetting to divide by once.

Where this shows up in industry

The Nyquist rate sets the minimum ADC sampling rate for telemetry and payload channels; in practice engineers sample faster than this and add an anti-aliasing filter.

From ISRO prep to a core electronics career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.