← Previous lessonFree lesson 3 of 3 · lesson 3 of 68

Unlock all 68 lessons of Structural Analysis and Design of Composite Structures using ETABSFull course ₹40,000 · paid

Price & syllabus
Free lesson · 22 min · no payment

Load Path from Slab to Soil and Behaviour of Slabs and Beams

A free lesson from Skill-Lync's Structural Analysis and Design of Composite Structures using ETABS course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Understanding Load Path in Structural Engineering”

What will you learn in this free Structural Analysis and Design of Composite Structures using ETABS lesson?

The instructor traces gravity load from slab to beam, column, pile cap, pile and soil, and explains the pressure bulb used to decide soil investigation depth. The lesson then describes slab behaviour as shell, plate or membrane, and classifies beams as simply supported, continuous, cantilever and propped cantilever.

  • Tracing gravity load from slab down to soil
  • Pressure bulb and soil investigation depth
  • Slab as shell, plate or membrane
  • Simply supported, continuous, cantilever and propped beams

What comes after lesson 3?

Later in Skill-Lync's Structural Analysis and Design of Composite Structures using ETABS course (paid): lesson 4, Column and Shear Wall Functions in Structural Design; lesson 5, Structural Systems in Composite Tall Structures; lesson 6, Braced Frame Behavior. The full course has 68 lessons (29 h 11 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

So, with this background, we will now move on to the load path of structure, how the load path takes place. So, the most important thing in a structure is how the load gets distributed into different structural elements, right? So, if you are able to assess a load path, that is like you would be able to address the behavior in the best way, like that is close to 70% of the work is done. But, if you are able to assess and evaluate the load path and the amount of the load.

So, now we will see what is the load path of a structure. So, how to assess that and how it gets transferred from a story to the foundation, right? So, from the slab, which is the horizontal element on which we have the partition loads, we have the dead load coming from the finishes, dead load coming from the self-weight, then we have the live load coming from the people moving on that floor, from the furniture and all. So, we have some gravity loads on the structure, on the slab, that gravity load has to be transferred through the vertical elements.

So, basically, that slab can be or may be supported on a beam. So, that load from the slab gets transferred to the beam. Again, that beam is further supported on the columns, which is the vertical element. And, from, through that columns, the load gets transferred to the pile caps. So, in the cases where we have a pile cap and the pile, the piling system is a foundation system. The loads from the columns get directly supported on the pile cap. And, then, from the pile cap, the load is further transferred to the piles.

And, from piles, there is a end bearing action possibility or there can be a skin friction action possibility. So, pile can transfer the load in either of those way or can be in terms of both simultaneously, the end bearing action as well as the skin friction action. So, through that, that whatever the load was there on the slab is directly transferred to the soil, basically, through piles. So, now, you see that any load which is there on the structure has to be, firstly, resisted by the individual elements, from one, transferred from one element to another.

And, at the end, everything has to be transferred back to the soil. And, we have to see that in this process, each and every element should not fail. So, the link should always be remaining same. So, the bridge between all these elements should remain the same. And, the last point, which is the soil, the load in the soil should not exceed or the stress in the soil should not exceed, such that the soil would not be able to take that load, right? So, there are two key components, how the connection works, how the member transfers the forces, and how the soil works, basically, to resist the forces.

So, similar to this, this is a type of a frame case, wherein we have set of columns, set of walls, beams, and then the load is resisted. Similar to that, we have a load-bearing action, wherein we have load-bearing walls, which can be a masonry wall or something. So, a masonry wall would resist the slab load. So, the loads on the slab would go to the masonry, then it goes further to the foundation. So, from the foundation, it can be a normal column footing or a strip footing on which it is supported.

So, if it is a brick wall, it would be a strip footing along the length of the wall. If it's a column, then there will be a single footing. And, that footing being again resisted on the soil. So, definitely at the end, the load will be dispersed in the soil. Now, you can see over here, there is one more thing which has been shown, which is, this is a width of the foundation. And, the depth is shown over here is 1.5 times the width. And, the dotted line is marked as a bulb of pressure.

So, this is called as a pressure bulb, wherein this zone is a zone, wherein there will be significantly higher stresses due to this load. So, once we move from 1.5B to 2B, which is below this point, there is no much influence of this load onto the soil. But, there is a zone of influence wherein the soil would be subjected to the stresses that will be somewhere close to 1.5 times of width of the footing. So, if you want to do a soil investigation and assess what are the soil capacities and all, what we have to do is, we have to assess the soil capacities up to 1.5 times of the foundation width.

So, if we can assess up to that, we can be sure that whatever assessment we have calculated, is the right assessment of the foundation systems. Similarly, if you want to calculate the soil capacities for the pile foundation, we have to see, we have to do a borehole up to the depth of the pile, which is the largest or the highest depth of the pile, we have to do a borehole up to that. And then we have to assess the soil properties for that depth. There are multiple ways of transferring the loads, but basically these are the two ways.

For the tall structures, definitely we don't have a bearing wall systems, but for the short or the small structures, we do have that. So, we could see this type of system in terms of bungalows, maybe three or four story buildings. But when we talk about the tall buildings, definitely we have this type of structure on the left, which is transfer of the gravity loads from slab to beams, beams, columns, columns to foundation systems. Foundation systems can be pile cap, can be raft, can be piles, right?

So, this is the methodology in which we see how the load gets transferred. Now, if you talk about the structural elements and the way it is, the load is transferred. So, the first part is the slab. The slab is the first element which resists the loads. So, once the load from the slab gets transferred to the beams on which the slab is supported, from beams those loads gets further to the columns. Columns are the vertical elements, whereas the beam are the horizontal elements. So, the vertical elements can be column or a wall.

And from those columns and wall, the load gets further to the foundation. So, this is the way and from foundation, definitely there is a soil. So, geotechnical engineers do that analysis that whatever the loads are coming from the structure, they need to be dispersed smoothly in the soil. So, that's a part of a geotechnical engineer. So, this is the way in which the total load transfer takes place in a typical structure. And if you are able to assess that, as I said, 60% of the problem gets solved by just plotting this type of a single line diagrams for the load flow path.

And this will help you in understanding the behavior of a structure. See, dotted line you can see over here. You can see the slab is not deflecting just axially, but it's also bending. This is a bending behavior, right? So, the primary action of the slab is in a bending direction, but that of a column is more like it has to transfer the axial forces. Now, with that axial forces, there is moments, but the major concern over here is an axial force. Same is for the piles.

The piles is generally supporting the compression forces and tension forces in the structure. So, if you are able to assess the load path in a structure, you are able to see the behavior of the individual elements, basically the slab, beams, columns, and the foundations. And we will see in the further how each element behaves under the loading conditions. So, we will start this with the structural slab. So, normally a floor slab, we say, where we all have our functional use of a building. So, whatever we are working on, living is all on the structural slab, right?

So, the purpose is to transfer the gravity loads of the floor onto the supporting elements. Apart from the transfer of the gravity loads, it also acts as a diaphragm to transfer the lateral loads. Now, I will come to this point further, but this also is one important function of the slab. So, we all understand, right? The floor slab has to transfer the load, the gravity loads. So, that's a default or a traditional, we understand. But, act as a diaphragm to transfer lateral loads would be something new for you.

And we have some slides at the end where you would be able to understand this in a better way. So, that house slab acts as a diaphragm for the lateral forces as well. So, it's not just the gravity, it also helps for the lateral. Then, this is the purpose, right? This was the purpose supporting the gravity loads acting as a diaphragm. Now, it has to satisfy its purpose via its behavior, right? So, how the member has to behave? It has to behave such that it satisfies its own purpose and the behavior is like we can consider three type of behaviors within the slab system.

So, I will say it like shells is the first way, blades and membranes. So, you would say like what do you mean by three behaviors, right? So, here I would say the basic behavior of the slab is out-of-plane bending, right? What you saw in the earlier diagram is the out-of-plane bending of the structure which is something like this. So, this is an out-of-plane bending. So, the plane of slab is the plane in which its longitudinal axis lies. And if you see, the bending is out-of-plane because now we have to go perpendicular direction to the axis of the slab.

So, this is called out-of-plane bending in the slab. There is also one mode that is in-plane bending in the slab. So, if our slab is bending along the axis, then it is called in-plane bending. So, it has both the functions like the out-of-plane direction bending and the in-plane direction of bending. If a slab is modeled as a shell, shell takes both into consideration in-plane action and out-of-plane action of the slab. Basically, the in-plane action, as I said, for the slab to act as a diaphragm. So, via diaphragm action, it would transfer the lateral loads.

So, if we model it as a shell, it acts as an in-plane and out-of-plane direction. It takes the behavior of bending in both the directions. If we model it as a plate, so if we model a slab as a plate, then it acts as an in-plane bending behavior only. So, there is no out-of-plane direction getting captured over here in terms of plates. And third is membranes. So, membranes only takes the axial tension and no bending, right? So, this is three ways, three different ways a slab can act.

Slab can act as a membrane. So, if you give, just to give an example, a thin sheet of the roof. You would have seen a plastic sheet at industrial structures which is covering the roof. So, that is a membrane which is acting in the tension only. There won't be any bending possible. It's a very, very thin sheet, right? So, it won't bend. So, it will break if it bends physically. So, the mode of resistance is through axial tension and compression. So, that is the way a membrane reacts.

Whereas, if we have some plates which is somewhere in walls, there is only in-plane bending. There won't be any out-of-plane bending of a structure. So, that behavior can be captured if you model it as a plate. And if we model a floor slab as a shell which is a normal behavior like usually for a buildings, the floor slab would act like a shell wherein there is an in-plane action as well as an out-of-plane action. Both involved in the resistance. So, this is all about slabs. We got an understanding about how it resists the behavior.

What is its purpose? So, similar to that, what we will see is from the slab, the load gets transferred to the beam, right? So, the next element would be beam. And its purpose is also similar to that of a slab. It transfers the load from slab to the columns, right? So, the beam is getting an intermediate member between the slab and the column. And again, similar to the slab, its primary behavior is bending. So, via bending, it resists the loadings. And those beams are further classified into simply supported based on the support conditions.

Now, we have already observed in the previous slides, we discussed about the connections, right? So, if you have pin connections at the end of a beam, then it would act as a simply supported beam. But if you have multiple pin conditions that would act as a continuous beam, if you fix at one end. So, if you have one end of the beam fixed and another end is free, that would be something like a cantilever. Just fixed at support, free at other. So, these are the three different classifications of a beam based on the support conditions.

But here, we should understand what's key behavior. So, behavior is of bending, right? Purpose is to transfer the loads from the slab to the columns. And for that transfer to take place, its behavior should be bending behavior. And based on the support conditions, there can be further three level of classifications for those beams. The simply supported, continuous, and the cantilever. Over and above that, we have a separate case within the cantilever, wherein if the free edge of a cantilever is supported via some support, then it's called a propped cantilever.

That is a propping at the end of free end, basically. So, that's the fourth case within the beams. Four different classifications. Now, we will see each of them separately and understand how their behavior is. So, if we talk about the simply supported beam, simply supported beam is the most commonly used beam. Like, if you talk about the beam universe, around 30 to 40 percent of the beams encountered would be simply supported beam. Like, for the gravity loads, you can see the F over here. So, the beam is having the pin joint at one end and the roller at the another.

So, as you all understand, pin joint supports two reactions, right? One in the horizontal and one in the vertical. Whereas, the roller acts only in the direction of vertical and not in the direction of horizontal. So, these three are the restraints available to us from the supports. And we have the force in these directions. So, you see a simply supported beam, just we have this support at the bottom, vertical directions. In one direction, it is restrained in the horizontal direction. It's called a simply supported beam.

Now, as I already said, because these are pin joints and this is a roller joint, there won't be any movement possible at this. Because movement restraint is not there, the beam would try to rotate at this end. And that rotation is allowed, right? Pin joint allows the rotation. Similarly, the roller joint allows the rotation. So, there won't be any movement at the supports. There won't be any support movement at this joint. There won't be any support movement at this joint. There would be definitely a movement at the center of the beam because there the force is acting, right?

So, the force interdistance would give us the movement. And that's how we calculate the movements for a simply supported beam. Now, if I go to the next wherein same the simply supported. Now, if we have two more intermediate supports like here, initially it was just one support at this end, one support at the right end. Now, we have two more additional supports brought into the picture. This becomes a continuous beam case. And this is more indeterminate structure considering there are more number of unknowns in terms of reactions.

So, if we talk about reactions first. So, these are all pin jointed, right? So, pin jointed would definitely have a horizontal and the vertical reaction. But in this case, we don't have an external horizontal force. So, as I said, external forces generate internal forces within the member. So, if we don't have an external force, there won't be any internal force. So, if we don't have any external force in horizontal direction, we don't have any internal restraints basically or internal forces in the horizontal direction. So, all we have is a vertical force.

So, all the vertical forces there external. So, internal forces would also be in vertical direction only. So, this is the direction of vertical force. But here there is to your amazement, what we all know that at the pin joint, there won't be any movement, right? So, here we don't have any movement. Here we don't have any movement. Here we don't have any movement. And here also we don't have any movement. But because this is an internal support, same as this, there will be movement on the either side of the beam.

Basically, there won't be movement at the center of a beam. But there will be movement in the either side of the beam. Okay. That will overall be effective. And thereby it will resist the external loads. And thereby they reduce the deflections. So, if we talk about simply supported beam and the continuous beam. So, this is a simply supported beam. If we enter two more supports at the center, it would act as a continuous beam. Now, because of this internal movement resistance, which is obtained due to adding of these two supports, the overall deflection in this beam reduces to that if compared with the simply supported beam.

Now, you got the point, right? So, whenever our beam is too long, now if you have a 10 meter or 12 meter long beam and that is not working with the simply supported actions, what we can do is we can make that beam continuous beams by adding two more supports. If we make it continuous, the length reduces. We get the help from the internal movements as well. And thereby the beam is gets worked out. So, as I said, if you can see in the picture as well, there is a bridge which is a continuous bridge.

These are the columns basically. It's called piers in terms of bridges. It helps us in reducing the deflection and making the beam work basically. So, the next part is the kin delivery beam, right? So, whenever we have a support, fixed support at one end and we have a free support at the other. So, if you can see all the balconies which we have in our tall buildings or structures. So, this slab over here which you can see is supported or fixed at the wall end. So, it is fixed at the wall, free at the other end, right?

So, this is called a typical cantilever case. Fixed rate support, free at end. So this type of, as I said, fixed gives us three types of internal reactions, which is the horizontal restraint, the vertical restraint, and a movement restraint as well. So there would be a movement also formed due to the gravity load of the slab that will be restrained by the wall. So this is how a cantilever beam is different to a simply supported beam and different to a continuous beam basically. Now, in the prop, I would like to say the prop is somewhat similar to just adding a prop at the free end. If we have one more support at the free end, if we have one more column over here, then it will act as a prop can deliver beam. Right. But again, as the here, the key point is for the fixed supports, we have three restraints, horizontal, vertical, and the movement restraint. And free end doesn't have any restraint. It's free to move.

Now, if you see what happens is you can see in the picture as well, because this is a cantilever part, that happens to be a large movement at the fixed end. And then you can see a lot many cracks occurring over below this surface. So this all cracks and all happens not in the case of simply supported beams, not in the case of continuous, but there is more probability to happen that in the case of cantilever beams. So while designing the cantilever beams, we should be very careful how we calculate, estimate the forces, how we provide our reinforcement and check whether that reinforcement, which we provided in our design is also getting casted in the site as well.

So that is very important.

Want the rest of Structural Analysis and Design of Composite Structures using ETABS?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Structural Analysis and Design of Composite Structures using ETABS course

The remaining 65 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Structural Analysis and Design of Composite Structures using ETABS course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.