← Previous lessonFree lesson 5 of 5 · lesson 5 of 72

Unlock all 72 lessons of Simulation and Design of Power Converters for EV using MATLAB and SimulinkFull course ₹40,000 · paid

Price & syllabus
Free lesson · 10 min · no payment

Drawing the Buck Converter in On and Off Modes

A free lesson from Skill-Lync's Simulation and Design of Power Converters for EV using MATLAB and Simulink course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to Switched Mode Power Converters, Performance and Analysis of Buck DC/DC Converter Week 1 Session 4”

What will you learn in this free Simulation and Design of Power Converters for EV using MATLAB and Simulink lesson?

The instructor reviews the golden rules for resistors, inductors and capacitors, including that inductor average voltage and capacitor average current are zero. The lesson then covers the first stage of buck analysis: drawing the circuit, marking average values, setting polarities, and redrawing it for MOSFET on and off modes.

  • Inductor and capacitor lossless golden rules
  • Average versus instantaneous variable notation
  • Assigning current directions and voltage polarities
  • MOSFET and diode as short or open circuits

What comes after lesson 5?

Later in Skill-Lync's Simulation and Design of Power Converters for EV using MATLAB and Simulink course (paid): lesson 6, Introduction to Switched Mode Power Converters, Performance and Analysis of Buck DC/DC Converter Week 1 Session 5; lesson 7, Introduction to Switched Mode Power Converters, Performance and Analysis of Buck DC/DC Converter Week 1 Session 6; lesson 8, Introduction to Switched Mode Power Converters, Performance and Analysis of Buck DC/DC Converter Week 1 Live session. The full course has 72 lessons (22 h 12 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hello everyone. So now we're going to start talking about the buck converter, performance, and analysis. So let's revise some of the golden rules that we talked about before. Again, they relate to the resistor, the inductor, and the capacitor. Voltage, current, and golden rule number two, that's the one that we mentioned before, that for the resistance, current and voltage can change instantly. The inductor current cannot change instantly for the inductor. The capacitor voltage cannot change instantly for the capacitor. There is another rule that we would like to remind ourselves of. The resistor can absorb power.

The resistor is basically an element where it can take power from the circuit. But the inductor and the capacitor, both of them are lossless. They don't consume any power. We're, of course, we're talking about ideal situation. We're not talking about the parasitics that comes, that come with them. So both of them are lossless. The average voltage of an inductor must be zero. The average current of a capacitor must be zero over a time period, which means that both of them are going to fly tooth and nail to make sure that they are going to stay lossless.

To make sure that the inductor average voltage is zero, that the capacitor average current is zero. These are the physical needs of them. So you cannot argue with that. If you try to break one of these rules, they are going to break the converter. They are going to break the circuit before you can break any of these rules. So now let's see the buck converter. That's what we came up with, that the buck converter is going to look something like that. We first started with a MOSFET and a resistance.

We found that we need some sort of filtering. So we added the capacitor. We found that we also need current filtering, not just voltage filtering. So we added the inductor. We found that the inductor needs to discharge. So we added this diode to be able to discharge the inductor. Now let's see how we're going to go about analyzing the performance of such a converter. So the first thing, we're going to do it in two different stages. Stage number one, we're going to make sure that we are drawing the buck converter properly.

And we're going to see what we mean by that. Stage number two, we want to make sure that we understand all the plots and equations that come with the buck converter. So let's get started. Stage one, drawing. What's the first step? The first step is basically to draw the converter circuit. And that's what we did right here. And if you notice, I didn't put any voltage values, any current values, nothing. This is just basically the converter circuit with nothing associated with it. What's the next step?

That would be to write down the average values of all the currents and voltages in the circuit. Average value. So a rule of thumb. Whenever we're writing a letter with high caps, that means this is the average value of these variables. So for example, V in capital means that's average input voltage. I L capital, that's the average inductor current. D L capital, that's the average inductor voltage and so on. So I'm just writing them down. I did not tell them what their direction should be. I did not tell them what their polarities should be.

I'm just writing them down. This is the next step in my drawing. After that, what we're going to do is we're going to try to assign some polarities and some directions to the voltages and the currents as we're going to see right here. So for the voltages and for the current, there is one rule that I want to follow. So whenever a current is coming through an element, it imposes positive polarity as it's going through the element, meaning that the first port or the first terminal of this element will be positive.

The second one will be negative. In the first one that the current will see. So for example, here, I L is coming from left to right. It's going to be positive negative. I C is coming up to down. It's going to be positive negative. I R coming up to down. It's going to be positive negative. You can make any assumptions. So I can make an assumption that I C is going up or I R is going up or I L is going left. Whatever assumption I'm going to make, it's fine.

As long as you keep that rule, when the current is passing through an element, it imposes a positive value. The next thing that we want to look at is to draw the converter circuit in the on and the off modes of operation. So what are the on and off modes of operation? The on mode relates to the time when my MOSFET is on. The off mode relates to the time when my MOSFET is off. So that's going to be my on mode of operation. I replaced my MOSFET with a short circuit.

And I replaced my diode with an open circuit. And in the off mode, I replaced my MOSFET with an open circuit. And I replaced my diode with a short circuit. Now let's look if that makes sense. So when the MOSFET is on, that means this is the input voltage. That means at this point, the input voltage is going to be imposed on this point. Which means that for the diode, it's going to be reversed bias. So it's true that the diode will be an open circuit.

And here, because the MOSFET is off, this is no longer happening. That the input voltage is imposed at this point. Which means that the diode will be able to conduct to carry the inductor current. Now, the other, after that, the next step is to write down the instant values of all current and voltages for each mode. So we would like to differentiate between two different things. When we are drawing the whole converter, meaning I'm keeping the MOSFET, I'm keeping the diode, I'm not replacing them with short circuits or open circuits.

I'm writing my values in capital letters. Because these are the average values. These are the values that are never happening at any certain point of time. That's just the average of my circuit. But when I'm writing the values during each mode of operation, I have to write them in small letters as we see right here. Because these are the instantaneous values. If you have a current probe or a voltage probe and you're looking at your converter right now, these are the values that you're going to see.

So that's for the on mode of operation. And we're writing the same thing for the off mode of operation. Remember, till now, I did not assign polarities. I did not assign directions for my buck converter. So the next step, logically, would be to assign polarities and directions for the buck converter in each mode of operation. Now, it's very important, very critical, to maintain the same polarity and the same arrows, meaning the same current direction assumed before. Before where? When I was looking at my average circuit.

So, for example, if IL is going from left to right in the on mode, it has to keep going in the same direction from left to right in the off mode. If IC going up to down in the on mode, it has to keep going up to down in the off mode. And same thing applies to the IR. And same thing applies to the voltage polarities. Because the voltage, the current, when it passes through the element, it's imposing a positive polarity, positive, negative across each element.

Okay? So, going through all of this, this really, if we are able to arrive here, we didn't yet finish analyzing the performance of our converter. All what we did so far is that we learned how to properly draw our converter, how to properly assign currents and voltage values for every single element, and how to properly maintain direction and polarities for my converter elements.

Want the rest of Simulation and Design of Power Converters for EV using MATLAB and Simulink?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Simulation and Design of Power Converters for EV using MATLAB and Simulink course

The remaining 67 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Simulation and Design of Power Converters for EV using MATLAB and Simulink course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.