Simulation and Design of Power Converters for EV using MATLAB and Simulink course by Skill-LyncFree · 5 lessons · no payment

Simulation and Design of Power Converters for EV using MATLAB and Simulink: 5 free lessons

Five free lessons from Skill-Lync's Simulation and Design of Power Converters for EV using MATLAB and Simulink course. They start with a MATLAB and Simulink primer, then introduce why switch mode power converters are used. The lessons compare a voltage divider, a linear regulator and a switching MOSFET, build up the buck converter step by step, and begin its analysis.

Last updated 16 Nov 2026 · 5 free lessons (1 h 17 min) · full course: 72 lessons (22 h 12 min), paid · ₹40,000

Lesson 1 of Simulation and Design of Power Converters for EV using MATLAB and Simulink: MATLAB and Simulink Basics Before the HEV CourseFree lesson 1 · 29 minMATLAB and Simulink Basics Before the HEV Course

What will you learn in the free Simulation and Design of Power Converters for EV using MATLAB and Simulink lessons?

  • MATLAB scripts and basic Simulink models
  • Why switching converters beat dividers and linear regulators
  • Resistor, inductor and capacitor rules for converters
  • Drawing the buck converter in on and off modes

Free lessons you can watch now

  1. Free lesson 1: MATLAB and Simulink Basics Before the HEV CourseLesson 1 · 29 minMATLAB and Simulink Basics Before the HEV CourseThe instructor tours the MATLAB environment, uses the command window as a calculator, and writes scripts for quadratic roots and a sine and cosine plot. The lesson then builds Simulink models with constant, add and display blocks and opens a built-in example that takes the maximum of several sine waves.
  2. Free lesson 2: Where Switch Mode Power Converters Are UsedLesson 2 · 7 minWhere Switch Mode Power Converters Are UsedA short introduction to switch mode power converters and why their design and simulation matter. The instructor goes through applications including solar and wind power, electric vehicle motor drives, data centers, laptop and phone chargers, and factory motor drives, and notes that a warm adapter shows power is still being lost.
  3. Free lesson 3: Power Conversion Goals, Switches and Linear AlternativesLesson 3 · 17 minPower Conversion Goals, Switches and Linear AlternativesThe instructor lists why power is converted: a set output voltage, a set current, maximum power extraction and a change of form between AC and DC. After covering the diode and N-channel MOSFET regions, a 100 V to 50 V example shows a voltage divider and a linear regulator both reach only 50 percent efficiency.
  4. Free lesson 4: Building the Buck Converter From a Switching MOSFETLesson 4 · 15 minBuilding the Buck Converter From a Switching MOSFETThe instructor starts from a MOSFET switching a 100 V input fully on and off, so the average output is 50 V at equal on and off time. After reviewing resistor, inductor and capacitor behavior, adding a capacitor, an inductor and a diode step by step arrives at the buck converter.
  5. Free lesson 5: Drawing the Buck Converter in On and Off ModesLesson 5 · 10 minDrawing the Buck Converter in On and Off ModesThe instructor reviews the golden rules for resistors, inductors and capacitors, including that inductor average voltage and capacitor average current are zero. The lesson then covers the first stage of buck analysis: drawing the circuit, marking average values, setting polarities, and redrawing it for MOSFET on and off modes.

Which lessons of Simulation and Design of Power Converters for EV using MATLAB and Simulink are free?

The first 5 lessons are free on Grow by Skill-Lync: 1 h 17 min of video from Skill-Lync's Simulation and Design of Power Converters for EV using MATLAB and Simulink course that you can watch here at no cost: leave your name and phone number once and they play (as of 16 Nov 2026). The full course is paid (₹40,000); its other 67 lessons are listed in the outline below so you can see what each one covers.

How long is the Simulation and Design of Power Converters for EV using MATLAB and Simulink course?

The full course has 72 lessons and 22 h 12 min of recorded video, plus the projects and assignments that come with enrolment. The free lessons alone take about 1 h 17 min, so you can finish them in an evening and decide whether to continue.

What comes after the free lessons?

Lesson 6 onwards is in the paid Simulation and Design of Power Converters for EV using MATLAB and Simulink course on Skill-Lync, with mentor support and a certificate. For a career in Electric vehicles, the Post Graduate Program in Electric Vehicle Design & Development goes further with industry projects and placement support.

Liked the free lessons?

Get the full course syllabus and fees.

The full Simulation and Design of Power Converters for EV using MATLAB and Simulink course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Simulation and Design of Power Converters for EV using MATLAB and Simulink course

The remaining 67 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.