Unlock all 72 lessons of Simulation and Design of Power Converters for EV using MATLAB and SimulinkFull course ₹40,000 · paid
Power Conversion Goals, Switches and Linear Alternatives
A free lesson from Skill-Lync's Simulation and Design of Power Converters for EV using MATLAB and Simulink course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to Switched Mode Power Converters, Performance and Analysis of Buck DC/DC Converter Week 1 Session 2”
What will you learn in this free Simulation and Design of Power Converters for EV using MATLAB and Simulink lesson?
The instructor lists why power is converted: a set output voltage, a set current, maximum power extraction and a change of form between AC and DC. After covering the diode and N-channel MOSFET regions, a 100 V to 50 V example shows a voltage divider and a linear regulator both reach only 50 percent efficiency.
- Voltage, current and waveform goals of conversion
- Diode and MOSFET operating regions
- Voltage divider losses at 50 mW and 500 W
- Linear regulator drawbacks for efficiency
What comes after lesson 3?
The next free lesson is lesson 4, “Building the Buck Converter From a Switching MOSFET” (15 min). Later in Skill-Lync's Simulation and Design of Power Converters for EV using MATLAB and Simulink course (paid): lesson 6, Introduction to Switched Mode Power Converters, Performance and Analysis of Buck DC/DC Converter Week 1 Session 5; lesson 7, Introduction to Switched Mode Power Converters, Performance and Analysis of Buck DC/DC Converter Week 1 Session 6; lesson 8, Introduction to Switched Mode Power Converters, Performance and Analysis of Buck DC/DC Converter Week 1 Live session. The full course has 72 lessons (22 h 12 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello everyone. So now we're going to talk about power conversion. How exactly does it happen? So briefly, power conversion means that I'm having some input power going to a system and then getting some output power out of it. And for that system to be able to do that, it's going to have to be a smart system. I'm going to have to feed this system with some data and information so that the power electronic system will be able to give me the output power that I'm looking for from the input power that entered into the system.
Now, of course, we know that we're not creating energy. We're not creating new power. All what we're doing is power conversion. So we're converting the input power into an output power. And why we're doing that? It's usually for one of these reasons. So we're going to have to achieve either one or more of these objectives. The first one, I have a very specifically desired output voltage. So for example, I would like to feed some loads that needs one volt as a voltage, or they need five volt to be able to operate, or they need 12 volt, or I'm feeding a battery at a certain voltage level.
So I have to convert whatever voltage I'm having here on the input side into the voltage that I can get on the output side. The other thing is, I would like to have a certain current level, not voltage level, current level. And that's certainly true in applications where, for example, the voltage is set for you already. So if you're charging your phone, and your charger is setting a certain current for your phone battery to be charged at, so that in 10 minutes or in 20 minutes, you're able to achieve full charge.
Now let's think about a higher power system. If I'm charging my electric vehicle, you might hear about fast charging, electric vehicle fast charging, or electric vehicle level one and level two and level three charging. What is that? All the difference between them is how much current you are feeding into your electric vehicle batteries. The higher the current, the less the time it's going to take to fully charge your electric vehicle. Another thing that you might want to get is a desired input power performance. And that's a little confusing because I'm telling you desired input power performance.
So for example, let's think that here I'm having a PV panel or a wind turbine. PV panels and wind turbines have specific IV characteristics. It's not the place to discuss that in details. But briefly, they have a specific input voltage characteristics. And we always want to extract the maximum power from my solar system and from my wind turbines. So the best way to do that is to have a power electronic system that is going to control the input power for me. So in this case, I'm not looking at whatever output power I'm going to give you.
I'm going to give you all what I have. But I care about the input power that I want to extract the maximum power from my input sources. And that's very specific to this kind of systems, photovoltaic or wind turbine or ocean energy, things that can, that has some flexibility to change. There is some flexibility for you to control. But for example, if you are feeding your, your loads from a power supply, from a power supply in your bench or from the electric grid or something, there isn't really a maximum power that you are tracking, then in this case, you're going to be looking at your load.
What does your load need? Another thing, which is probably the most famous for most introductory power electronic students, is that I'm doing that to achieve a desired shape or form. So we know that I can go from AC to DC. An example of that would be going from the electrical grid to charge my phone or to charge my laptop or to charge an electric vehicle. I know that I can go from DC to DC. An example of that would be a PV panel feeding a battery.
I know that I can go from DC to AC. An example of that would be any DC system, whether batteries or PV panels or fuel cells, that's feeding my electrical grid. Or inside the electric vehicle, you have your batteries and you have your motor. Beside them, there is a DC to AC power electronic converter. Another thing is going from AC to AC, which is also called variable frequency driver, in which case you are getting the AC power, changing it completely, and getting another AC power. Now, what you are changing might be the frequency, might be the shape.
There are many things that you might be able to do. An example of that would be a wind turbine that is feeding into the electrical grid. So the wind turbine by itself is generating AC power, but then I treat this AC power and I process it through my power electronic conversion. And then I feed it back to the grid as AC power, but with a different shape or at a different frequency. Now, one of the most important things in all of that is your ability to increase and enhance the efficiency of your system.
And that's a term that we're going to be using quite a bit. And your efficiency is basically your output power by your input power. Now, the second thing that we would like to discuss is some of the main switches and some of the main components that we're going to be using in our system. So one of them is the diode. So this is the diode here. And right now we're not going into details with that because there is another time that we will do this. But the diode is basically an uncontrollable switch.
You don't control the diode. The diode conducts when the voltage on the anode is higher than the voltage on the cathode. And that's it. So as long as this voltage is not higher than this voltage, then the diode will always be conducting. But here what we're looking at is the MOSFET. So that's a figure of a MOSFET. And actually, that's an N-channel MOSFET, which is the most commonly used in power converters. And that's also the most commonly active switch used. When we say active switch, we mean a switch that you can turn on and off by yourself.
You can completely control when to turn it on and when to turn it off. Now, we're going to go brush over this really fast that there are several regions for your MOSFET. You have the linear region, which is also where you can completely turn your MOSFET on. And there are some conditions for that. The main condition is about VGS, the voltage between the gate and the source. Two things have to happen. This VGS has to be bigger than the threshold voltage of your MOSFET. And also VGS has to be bigger than the threshold plus VDS.
There is also the saturation region, and that's also VGS is bigger than them, but it's not bigger than VDS plus D threshold. And that's usually this region is used mostly in the operational amplifier applications, which is not what we are discussing in this course. And finally, there is the cutoff region, and that's briefly when VGS is lower than the threshold, and that's also the period when the transistor is fully off. So, there are basically here, when we're talking about switch mode power converters, we're talking about these green regions.
When the transistor is fully on and when the transistor is fully off. So, when it's fully off, as you see here, ID is almost zero. There is no ID. Only, there is only VDS. And when you see here, when it's fully on, VDS is almost zero. It's very small, but I'm mostly having ID. So, ideally, I would like to think as, for the transistor when it's fully on, as if it's a short circuit. As if I am shorting between the drain and the source. And when it's fully off, it's an open circuit.
So, as if this here is open, so there is no connection between the drain and the source. So, the next thing that we would like to look at is, let's assume that I have an input voltage of 100 volt. And I would like to convert this 100 volt into a 50 volt at the output side. Then, what are my options? What are the different solutions that I have to achieve this? So we're going to look at three different options, and we're going to see which one of them will make the most sense for us.
Now the first one is basically use a voltage divider, right? Why not? So you want to get 50 volt out of 100 volt? Well, there is a very simple math that you can use a voltage divider. If you make R1 equal to R2, Vout is going to be equal to half of the V input. All right, so the output power in this case will be, so we're going to look at two cases. The first case, when I'm having low output power, that's for me is 50 milliwatt.
And R1 and R2 to get 50 milliwatt at 50 volt on the output side, that means that R1 and R2 will be 50 kilo ohm, right? Because we know that the power is equal to V squared over the resistance. In which case, I'm going to get my output power, 50 milliwatt. But how much power did I lose in the system? Now remember, that's your input voltage, and that's your output voltage. Everything that happens in between, I don't really care for. So, any power that I'm losing here, I'm not gaining anything of it.
That's not my load. This is just part of my power electronic system. So, all of the power that I'm losing in R1 are gone. Bye-bye. I'm never going to see them back. So, these power losses are going to be the conduction losses through R1, which is the square of my current multiplied by the resistance, which is 50 milliwatt. So, if you see here, my output power is 50 milliwatt. My power losses are 50 milliwatt. So, when you see that, it's like, we're not really sure if that's the right way for us to go.
But, you only lost 50 milliwatt. So, maybe it's not a terrible thing. Which means that, in low power applications, using a voltage divider could be a good idea. But, let's look at case 2, where the output power is 500 watt instead of 50 milliwatt. Now, I'm going to have to design R1 and R2 to be 5 ohm each. Because, again, the power is equal to V square over the resistance. And V, as we said before, we want it to be 50 volt. So, now the output power is 500 watt.
How much are your power losses? What do you think? It's going to be exactly 500 watts, similarly to case 1. So, again, I lost half of my power, but now it hurts much more, because I'm losing 500 watts. So, the biggest advantage of this method is that it's very simple. You just need a couple of resistors. It's very cheap. But, what are the drawbacks? My efficiency here is 50%. And, the other thing is, it's a static system. Unless you're using a pitontometer here, then you have no way to change your output voltage.
Your output voltage is always going to be half of your input voltage. The other thing is that the efficiency here is 50%, but in some cases it can get much lower. Now, think that you want to get the 100 volt into 10 volt. That means I'm going to be losing 90 volt on R1, in which case my efficiency will be 10%. So, it's a terrible system in terms of efficiency. But, it's simple. It's cheap. It's good for very low power applications, where you don't need a dynamic system, where a static system will be good enough for you.
Now, let's look at another solution, which is using a linear regulator. Now, if you remember, when we looked at the characteristics of a MOSFET, there was a region where, if you increase ID, VDS increases. So, basically, a linear regulator is very similar to the voltage divider, but you replace R1 that we had here. Remember, when we had R1 and R2. You will replace R1 with a MOSFET, or an IGBD. Both of them are going to have this capability. But, let's say that you're going to replace it here with an active switch, where the current and the voltage are linearly dependent.
So, you're going to be working in the region where there is a linear dependency between them. So, if you increase the current, you're increasing the voltage, and if you're increasing the voltage, you're increasing the current. What does that remind you of? It's a resistor. It's practically a resistor, but a resistor that you can control. So, if we're doing the same exact thing, we're trying to get 50 volts out of 100 volts, you're going to find that the MOSFET will need to drop 50% of the system voltage.
And, look here, the same current is passing through the whole circuit, which means that when I'm dropping half of the voltage at the same exact current. It means I'm dropping half of the efficiency, because current multiplied by voltage is power. Half of the power is here, and the other half is there. So, now, it's also simple. I know we added a MOSFET, but it's not that sophisticated way to control it. We're going to need to control it, but it's not a sophisticated way to control it.
It's still cheap, because linear regulators are much cheaper than switch mode power converters. And, it's dynamic, so it's giving you that extra element. So, this is also good for systems at low power, where the efficiency is not a great concern, but you need some sense of dynamic ability. You want to be able to control the output voltage based on the control signal that you are feeding into your active switch. So, looking at the voltage divider, the linear regulator, both of them are not going to work for systems where we are looking for high system efficiency.
So, this is just a recovery store at low power, you can even creat the growth rate if you're using multiple devices. So, now, you're going to need some people to control it. Thank you.