← Course overviewFree lesson 1 of 3 · lesson 1 of 54Next lesson →

Unlock all 54 lessons of Mastering Shear Force and Bending Moment DiagramsFull course ₹40,000 · paid

Price & syllabus
Free lesson · 37 min · no payment

Stress, Strain, Hooke's Law and the Steel Stress-Strain Curve

A free lesson from Skill-Lync's Mastering Shear Force and Bending Moment Diagrams course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Mastering Bending Moment and Shear Force Diagrams”

What will you learn in this free Mastering Shear Force and Bending Moment Diagrams lesson?

The instructor outlines the 12-week course, then defines axial and shear strain and stress, elastic versus inelastic deformation, and Hooke's law with the modulus of elasticity E and shear modulus G. The lesson walks through a steel stress-strain curve point by point, from proportional limit to yield, ultimate strength and fracture.

  • Axial and shear strain and stress definitions
  • Elastic versus inelastic deformation
  • Hooke's law and modulus of elasticity
  • Reading points A to E on the steel curve

What comes after lesson 1?

The next free lesson is lesson 2, “Idealized Steel and Concrete Curves, Equilibrium and Its Types” (30 min). Later in Skill-Lync's Mastering Shear Force and Bending Moment Diagrams course (paid): lesson 4, Mastering Bending Moment and Shear Force Diagrams; lesson 5, Bending Moment and Shear Force Analysis in Beams; lesson 6, Analysis of a Simply Supported Beam with Triangular Loading. The full course has 54 lessons (27 h 10 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hello, everybody. Welcome to the course, Mastering Bending Moment and Sheer Force Diagrams. This is a 12-week course wherein we will be covering bending moment and shear force diagrams of different types of beams and frames, which will be subjected to gravity loads as well as lateral loads. This course is actually a good primer for fresh graduates who will be appearing in job interviews. So, it will definitely help them refresh their concepts of bending moment and shear force diagrams, which is a very critical aspect for any job interview from a structural engineering standpoint.

So, with this, let's get started. So, this is week one. So, in week one, we will be covering introduction to concepts of mechanics. So, these are the few things that we are going to cover in week one course. So, first of all, we will be touching upon concepts of stress and strain. Secondly, Hooke's Law. Then, we will be moving on to stress-strain curves for steel and concrete, which we know is a very common material which is used in the construction industry. Then, we will be moving on to the important aspects of stress-strain curve, where we will be discussing different, you know, key elements and key aspects of the stress-strain curve, like what are the important points to be noted over there, and then like steel and concrete obviously have a different behavior.

So, they will have, they will exhibit different kind of behavior over there. So, that's what we will be touching upon. Then, we will be moving on to equilibrium and its types, because ultimately, any structure to be built, it has to be in equilibrium, and that's where stability comes into picture. So, we will be touching upon that. We will also be looking at the equilibrium equations, which we typically deal with, and then we will be moving on to introduction to beams, which is a very, very common type of structural element that we deal with.

Then, we will be moving on to different types of beams, based on their different spans or maybe different supporting conditions and stuff of that sort. And then, we will be moving on to types of support, and then lastly, we will be looking at the equilibrium equations for beams. So, this week, we will be learning about the basic concepts of stress and strain, which is a very, very basic thing from a mechanics standpoint. After that, we will be looking at the equilibrium and types and the governing equations.

And then, we will be looking at the beams. So, with this, let's get started on the stress and strain part. So, as we know, whenever a deformable body is subjected to any external load, it deforms. And this is a very critical aspect to be known. So, whatever materials we typically deal with, they are all deformable. And what that means is, like, they have a very finite stiffness. They don't have infinite stiffness in that they always, I mean, they don't behave like a rigid body. As such, they are more like, like, if you apply any load on that beam or any element, for example, that beam will undergo certain kind of deformations just due to the application of those loads.

And that is what is known as a deformable body. And a stress or a strain could develop in a body which is deformable. So, this concept does not really apply to any rigid element. So, that's the reason a deformable body is highlighted here. Now, any body could be subjected to various kinds of deformations. So, the three primary ones have been actually listed over here. So, one is axial, which could be either elongation or compression of the member. So, axial is basically a deformation which is in the longitudinal direction of the element.

And that's why axial. And then it could either elongate or stretch or increase in dimension. Or it could compress or reduce in length or dimension. So, that's why these two types. And then elongation is also known as tension. And then compression is obviously known as compression. The other types of deformation that we deal with is transverse, which could be due to transverse loading on any element. And that results in shearing or bending of that element. So, by bending, we mean like whenever a load is applied, that kind of creates some kind of a curvature in that element.

And that is what actually gives birth to the bending moments and all in the cross-section. And similarly, shearing is more of like if you apply a transverse load on any element. So, two planes kind of try to rub against each other. And therefore, there's that shear deformation that actually happens. And that is what is known as shearing of the element, which we'll be discussing more into that in detail in the coming slides. And the third basic type of deformation is twisting, which is nothing but if you have, say, an element which is subjected to torsion.

So, that kind of leads that element to twist. And by twisting, we mean the element kind of deforms in a rotational way about its longitudinal axis. So, for example, if you consider a shaft which is subjected to a torsion, in that case, that shaft is going to twist. And that is what the deformation twisting entails. And then also from a 3D deformation standpoint, we also have something known as a volumetric deformation, wherein due to the applied load, the entire volume of the element changes. So, just an example that we have given here is an inflation of beam.

But it could be any type of other volumetric change as well, which could happen, which is kind of substantial. So, if the initial volume of an element was, say, V, and then due to some application of external pressure, the volume actually changed to V dashed. That's where the volume change actually comes into picture. So, now let's move on to the stress and strain part. So, consider we have a body, which is the one which is shown in blue outline here. So, it's basically a body with a very random shape.

And then that is subjected to these external forces, which are F1, F2, F3, and F4. So, these are basically a system of forces, which is acted upon on the body with a blue outline. And then, obviously, this body is deformable. It is going to undergo deformation due to application of the external loads. And then, once these loads are applied, the body deforms to take the shape which is shown in green. So, that is what we are showing over here. Like, due to the application of the different loads, like F1, F2, F3, and F4, the body, which was blue initially, changes its shape to green.

Now, this is kind of an exaggerated diagram, if you will, because in reality, the deformation could be very low, depending on the stiffness of the element. But, just for the explanation purpose, like I have just shown it to undergo such kind of high deformation, so that the intent is clear. So, what is stress and strain? So, whenever we have a body, which is obviously deformable, so, let's just consider, say, a body over here, which is subjected to some kind of an axial load, which is tension in this case.

So, consider this body here, which is shown in red. And then, that is not submitted to any load as of now. So, this is its original shape. Now, when we apply a load in the tension direction, so that, you know, that creates kind of an elongation for the body. In that case, it takes the shape of this blue dotted line that we see here, wherein these faces actually kind of elongate. So, therefore, like there's a net increase in the length of the member. But, at the same time, due to Pauson's effect, which we'll be getting into a bit later, due to Pauson's effect, the lateral displacement or the lateral dimension of the body actually reduces.

So, if there's an increase in length, there'll be a lateral negative deformation. And then, if you had a compression or rather a loading, which is going to create a compression in the longitudinal direction, so that would lead into the transverse dimension getting expanded. So, this is the deformed shape that we get once we have applied the load. And now, once we start unloading or when we fully unload the structure so that there is no external load at all, the element regains its true original shape that it was.

So, this is known as an elastic deformation. So, whatever load was applied to the element, that load once gets removed, the deformation that was there in the element also gets nullified. So, the shape that the body had and the dimensions that the body had before the loading was applied changes exactly to the same dimension and the shape right after unloading the element. And that is what is known as an elastic deformation. The body said to be elastic within that range wherein if you load that element and then you unload, the body regains its shape and configuration or the original shape and configuration after unloading.

The second type of deformation would be inelastic deformation. So, in inelastic deformation, so imagine again we consider the same body here, but then we have loaded that body such that it reaches this blue dotted line shape. But then after we have unloaded, it gets this shape here which is shown in blue dotted line which is filled in blue. So, here as we can see, this has not really fully regained its original shape. It has just partially regained. So, therefore, there is some permanent deformation that has happened in the body and it was not really able to regain the entire shape and dimensions that it originally had before unloading.

So, this kind of deformation which is permanent and cannot be reduced again, that is known as inelastic deformation. Now, let us move on to the axial strain. Now, let us move on to the axial strain. or actual deformation. So, as we discussed before, an actual deformation is basically a deformation which happens along the longitudinal direction of the element. So, as mentioned here, like a deformation of a body in a given direction per the body's original dimension in the same direction. So, that means basically if you say apply a compression load or a normal force over here, so in the same direction of load, you are able to see the deformation in the beam.

So, initially the element was say with the red outline that we are seeing here wherein the load is applied. So, due to compression, the overall length of the member reduces because it is getting compressed and the blue element here is actually the shape that it has achieved after getting compression. So, here the primary deformation is in the direction of the loading. So, here the primary deformation is in the direction of the loading that was applied. So, therefore, this is known as an axial strain. Strain is a dimensionless quantity. So, what strain is, is basically, strain is nothing but the deformation of the body per unit original dimension.

And that is actually mathematically expressed as a differential. But then, just for the illustration purpose as of now, we just consider this to be a deformation of the body per its unit length in that same direction. So, the loading direction here is along the longitudinal axis of the member. So, therefore, the length of this member along the longitudinal axis is say L. And then, due to application of this load, the deformation in the body in that same direction is delta. So, in that case, the strain in the body will be equal to delta over L.

And that's what is mentioned here. Like, if a bar of initial length L is subjected to a load such that it deforms axially by an amount delta, in that case, the strain is equal to delta over L. So, this is a very mathematically simplified version of strain. But in reality, these are more of a differential equations that we typically deal with. But to keep it simple, for now, we can just consider the strain as the ratio of the deformation of the body to the initial dimension of that same body in that direction.

And then, if the body contracts, in that case, the deformation is considered as compression because that is reducing the length. And therefore, typically, per the sign convention that is used in the industry, that is considered as a negative strain. And then, if there is an elongation in the body wherein the final length is higher than the initial length, in that case, that is known as a tensile strain. And that is considered positive. That's because there was a net increase in the dimension in the direction of the load.

And therefore, that is considered as a positive deformation. Moving on. So, this is a shear strain that we also discussed before. So, this is more of a transverse strain wherein if we consider, say, a body of, say, dimension H, height is H, and then we have some length, say, L over here, and then, say, the initial length or the angle between the two sides over here was theta 1. And then, here, the load is actually applied on one of the faces of this element, which is shown over here.

So, what happens is, like, once this load is applied, this is kind of the deformation that the body sees over here. So, there is no tension or compression here, but this is more of an angular displacement, or which is also known as a shearing between the two faces. So, in reality, like, this H could be very, very small, but just for illustration purpose, this has been kept pretty high. So, in that case, what happens is, like, these two planes could be very, very close to each other.

And therefore, once the load is applied in that direction, the angle that was initially there between these two faces, which is indicated as theta 1 here, that actually becomes theta 2. So, what's happening is, there is this differential displacement here, which is delta, which is indicated by the horizontal distance in the applied force direction, which is delta, and therefore, I mean, this is measured along the applied force direction. So, this delta is that deformation of the upper face with respect to the bottom face. So, in reality, like, the lower face could also have deformed.

The upper face also has deformed. But the relative deformation of the upper face with respect to the lower face is delta. And then this height over here is H. So, in that case, the strain here, or the shear strain, rather, is actually considered as this angular displacement, which is change in angle. So, that means theta 2 minus theta 1 will actually be equal to the strain or the change in angle. And that, and since these are very, very small deformations, so for our practical purposes, that change in angle is actually equal to tan theta, and then tan theta is equal to delta over H.

Since delta is very, very small, we could consider theta as tan theta. And therefore, the shear strain is equal to delta over H. And that is what is mentioned here. Like, it is defined as the ratio of the relative deformation between two points to the perpendicular distance H between them. So, this relative deformation is very important because, as I mentioned before, like, this point could also deform, say, to some number, and then this one would also have deformed. So, it's always the relative deformation that we are always talking about.

So, it's a relative deformation between this point and this point here, which is delta. And delta over H gives us the shear strain. And this is obviously when delta is very, very small, and that's kind of the deformation we typically deal with in the industry. Now, let's look at the stress. So, whenever there's a strain that is accompanied by stress, so, due to this internal deformation in the body, which is strain, so, there it develops an internal force in the body, which is actually trying to resist the external force applied.

And that internal force which is developed is kind of the resistance that the body is trying to offer to the applied load, so that the body is in equilibrium for its stability. So, now, stress is nothing but the ratio of the internal force over an area to the area of the cross-section on which it is developed. So, the force will always act on some kind of a finite area. So, that's the magnitude of force. And then, the magnitude of area is, say, A. So, in that case, the stress is actually given by P over A.

And then, the limiting value of A. So, if we consider a limiting value of A to 0, so, that is this ratio. So, P over A with A limit 10th turning towards 0. So, this ratio is known as the stress. So, now, this, similar to strain, stress could also be of different types. It could be an axial stress. It could be shear stress. It could be a torsional stress as well. So, strain and stress come hand in hand. So, whatever is the kind of strain developed, we always get the corresponding type of stress developed in the same body.

So, if there's an axial deformation in the body or there's an axial strain, that will give birth to axial stress. If you have a shear stress in the body or shear strain rather in the body, in that case, that is going to give birth to shear stress. And then, similarly, if you have a bending strain in the body, so that's going to give birth to a bending stress. And then, the expression for stress is P over A. And then, when we do the corresponding differential, so, if we consider this A tending towards 0, so, P over A gives us the corresponding stress developed.

So, as we mentioned, the stress could actually be axial, similar to strain. So, it could be both tensile or compressive. So, whenever we have a tensile strain wherein the body elongates due to the applied load. So, therefore, that also produces a tensile stress in the body. And then, similarly, if you have a compressive load applied in the body, so, which results in a compressive strain. So, the internal forces or the internal stress developed in the body is also compressive in nature. And then, just for the sake of simplicity, what we typically do is, like, for an actually loaded bar, say, we consider an actually loaded bar, which is applied a normal load, say, P.

And then, the cross-sectional area of the bar is, say, A. So, in that case, the expression for stress is P over A. So, as we saw, like, in reality, this is basically, like, stress is equal to this differential here, which is wherein, you know, A is tending towards 0, and then P over A is that corresponding ratio. But then, here, like, when we say P, sigma equal to P over A, the assumption is that the stress does not really vary across the cross-section. So, in that case, like, P over A kind of is the constant stress magnitude that we have on that cross-section.

And as we mentioned before, like, if P is, or the applied load is tensile in nature, in that case, the stress would also be tensile because that is resulting in elongation of the member. And then, if the force applied is compressive in nature, so, in that case, the nature of stress would also be compressive. Okay. Now, we also look at the shear stress. So, this is very, very similar to the normal stress that we looked at. So, as we said before, like, if there's a normal strain, that gives birth to normal stress.

So, similarly, if you have a shear strain, that gives birth to shear stress. So, as we saw before, so, consider you have this kind of, you know, a 3D parallelogram element here. And then, there's this shear force V applied on this body, which, or this face, rather, which has an area of A, which is mentioned here. So, this is applied force V. So, this is applied force V. So, this is applied force V. So, this is applied force V. So, this is applied force V. So, this is applied force V.

And this load is applied on this surface A. And the result of this load is shearing of this entire element. So this angular displacement, like we could see, like this was initially perpendicular, but then due to the application of this load, this entire body kind of sheared. And therefore, the angle between these two was no longer 90 degrees. It was something less than that. So that is the reason, like this is kind of causing a shear strain. So the magnitude of the load applied, V, divided by the area on which it is applied, which is A.

So as mentioned here, like with a, so it's basically similar to what we were considering for the normal stress, wherein we were saying like for normal stress, the stress will be equal to P over A with A tending towards 0. So it's more of a differential expression. So similarly, for a shear as well, it's just that the applied normal load is replaced with a applied shear load. And then this area is equal to the area of the surface on which that shear force is acting. And as mentioned, like axial stress, shear stress is basically the ratio of the internal shear force developed over an area to the area of the cross section on which it is developed.

So as I mentioned before, like whenever we talk about stress, that is always something which is developed internally and not externally. So there's an actual, I mean, we could have a body which is subjected to an external load, but the body has to resist that load. And the way it resists those loads is by developing internal forces. So all of these stresses that we're talking about here are actually developed internally. And that is the reason the term developed has been used everywhere. All right, let's move on to the relationship between stress and strain.

So as we saw before, like stress and strain, these are all physical quantities. So strain is related to a deformation and then stress is related to the internal force developed. So there is always a relation that is present between the developed stress and strain. So the stress developed in a material is a function of applied forces and deformation undergone by the element. The deformation in a material is primarily a function of the applied load and the stiffness of the member. So stiffness is nothing but it's a measure of the resistance that an element offers to an applied load.

So if a member is pretty stiff, in that case, it is, it's going to undergo a very small deformation for a given loading. But if a member is not very stiff, in that case, it's going to undergo a pretty large deformation for the same applied load. So one thing to note here is strain does not depend on the stress developed. It just depends on the stiffness of the member. As we mentioned, so strain is something which is related to deformation of a body. So in that case, if you have a very stiff element, in that case, if you have a pretty high load applied, I mean, for the same element, you could see a higher deformation if the applied load is higher.

And then if the applied load is lower, in that case, the body will undergo lesser deformation. So that has got nothing to do with the stress developed. This is more of the property of the member, the stiffness property of the member. So strain does not depend on the stress developed. Strain depends on the magnitude of the load that has been applied and the stiffness of the member. Whereas stress, on the other hand, which is developed, is actually a function of strain. So the higher the strain, the more the stress.

So there is a proportional relation between stress and strain, wherein higher the strain, higher the stress. So one thing which is very important to note here is strain is an independent quantity and stress is a dependent quantity. Stress is actually a dependent quantity and stress depends on the strain of the element. But strain is an independent quantity, which we mentioned. Like strain is basically dependent on the load applied and the stiffness of the member. There are a lot of constitutive relations established, which is basically the relations between stress and strain.

I mean, that is known as a constitutive relation. So there have been a lot of studies done. And therefore, there have been a lot of relations developed between stress and strain. And this is valid for both like longitudinal strain, which is compression or tension. And then it also applies to a shearing stress and the shearing strain. So we have relations between longitudinal stress and longitudinal strain. We also have relations between shearing stress and shearing strain. And all of that is known as constitutive relation. And we have a very, very popular law, which is named as Hooke's law.

And that is nothing but it's kind of a simplified form of constitutive relation. So Hooke's law kind of defines the relation between stress and strain. And then let's move on to the Hooke's law. So Hooke's law, what does Hooke's law state? So Hooke's law states that stress developed in an elastic material loaded within elastic limit is directly proportional to the strain in the element. So there are a few things which are very, very important to note here. One is that the stress developed in an elastic material.

So when we say elastic material, we are saying, as we discussed before, elastic deformation is something wherein if a load is applied, the body deforms. And then once the load is removed, the body regains its original configuration and shape. So that is elasticity of that material. So Hooke's law is valid only on an elastic material. It does not qualify to be valid for an inelastic material. So that's one important thing. The other is the material has to be loaded within elastic limit. So that means there are a few materials which could exhibit elasticity within a given range of strain.

And beyond that, the body starts to deform permanently. So Hooke's law is valid only till the point wherein the load applied is within elastic limit of that material. So under these two conditions, what Hooke's law says is that the stress developed in a body is directly proportional to the strain in the element. So that's what is mentioned here. Sigma, which is a common denotion for stress, is proportional or directly proportional to the epsilon symbol here, which is indicating strain. And that's what's mentioned here. Sigma is stress and epsilon is strain.

So in mathematical form, that is known as, it could be written as a sigma is equal to E multiplied with strain because we have a linear proportionality between stress and strain. So that proportionality constant E is known as modulus of elasticity of the material. So E is actually a material property. So for a given material, say it's steel or concrete or aluminum or whatever other material which is typically used in the industry. So E is a material property or a material constant. So E does not really depend on applied load or strain and all.

That's more of an independent quantity. And then we have this epsilon, which is the strain, which is developed in the body due to deformation. So E multiplied with epsilon gives us stress. And this is the mathematical form of Hooke's law. Similarly, we have relations between shear stress tau and shear strain gamma. And the relation is shear stress is equal to G multiplied with gamma, wherein G is that proportionality constant. And that is shear modulus of elasticity and similar to the Young's modulus or the modulus of elasticity, G is also a material property.

Now, let's look at some of the stress strain curves of some common materials that we typically deal with in the industry. So the first one being steel. So for steel, this is kind of the graph that we obtain, wherein in the y-axis, we have the stress plotted and in the x-axis, we have the strain plotted. So when a steel bar, say, is loaded, actually, and subjected to tension, with very, very gradual increment of loading, in that case, so the loading always starts from zero. And then we keep on increasing that loading with a slow increment.

So as we keep increasing the loading, the deformation in the bar also keeps increasing. And the relation between the applied load and the deformation would initially be linear. And that's where we see a straight line that goes all the way up to point A. So till point A, there's a linear relation between stress and strain. And this is where we have the elastic behavior exhibited. And this is where the Hooke's law is valid between point O and A. Now A is known as the proportional limit.

So the reason it has this name proportional limit is because only till point A, the linear proportionality relation between stress and strain is valid. Beyond point A, that relation is not valid. And therefore, Hooke's law is not valid as well. And that's the reason this is known as proportional limit. So till point A, Hooke's law is valid. And beyond point A, Hooke's law is not valid. So once we start from point A and now the loading is now further increased, so it starts to curve. So if we see here, this kind of starts to curve because the linear relation is lost now.

And then it reaches this point B, which is known as yield point or elastic limit. So point B is a point. Which is a yield point. So what happens is like till point B, the increase in strain in the element due to increase in applied loading wasn't very substantial, but then beyond yield point, the increase in strain is much higher compared to the increase in stress. In other words, the resistance offered by the material beyond point B is not high, but it undergoes a lot of deformation.

And that is where we would see that this curve between stress and strain gets to flatten. So now let's move on to point C. So point C is something which is actually used to determine the permanent set in the material. So if we see here, so this is actually a permanent set, and that could be anything between 0 to 1%. So let's say if the permanent set is 1%, so what that means is if the initial length of the body was L, in that case, and then the permanent set is 1%, for example, in that case, what that means is there's a permanent deformation in the body, which is equal to 0.01 into L.

So if that was the case, in that case, if we drew a straight line parallel to the initial elastic line that we had, so that's the point that we get here, C. So point C is known as the proof stress, and that is basically the stress corresponding to the permanent set, which is equal to the permanent deformation that the body has undergone, and that cannot be recovered at all. And that's why it's permanent. And beyond C is basically wherein the material actually starts to exhibit plastic behavior.

So plastic is exactly opposite of elastic, in that, like here, wherever the stress is increased, the strain also increases with that. But then beyond this point C, typically what happens is, this is the point wherein, like whatever deformation we are seeing is actually within inelastic limit, and then that deformation is not going to, I mean, the material is not going to get back that deformation. So these are all permanent deformation that we're talking about here. So beyond, beyond point C, that's known as plastic behavior, so as the applied load keeps increasing, there's not a very substantial increase in the internal stress developed, but then the strain increases with a much higher rate now.

So that means that the body starts to deform much faster with respect to the very gradual increment in the load applied. So, and this is also known as strain hardening, but that is not really in the scope of this course, so we won't cover that. But just to know, so once we load beyond point C, there is still some increase in the internal stress developed, and that increment happens until we reach point D. So point D is the maximum stress or the tensile stress that could be developed in that material, and that is also known as the ultimate tensile strength of that material.

So this is the maximum stress that could be developed within the material, and beyond this, the material starts to lose its resistance pretty fast. And therefore, like once you load the material further beyond point D, the strain in the element increases a lot, and the internal stress developed actually keeps reducing, and the internal stress is nothing but the resistance offered by that material. So, beyond point D, the internal stress starts to reduce very fast, and therefore we reach this point E, which is known as the fracture point, wherein that material or the bar actually breaks.

So, so we started off with point O, wherein the load is started to applied. So point A, just to recap, so point A is wherein till which we have the elastic or the linear proportionality between stress and strain maintained. Beyond point A is where the nonlinear behavior between stress and strain starts to exhibit, and then we reach point B, which is the yield point of the material, and the stress corresponding to that yield point is known as yield stress, and that is a very, very important or critical aspect of any material, because that's what we typically deal with in our, whenever we do structural engineering and we design any elements, so whatever materials we deal with.

So, I mean, for example, if we consider steel rebar for a reinforced concrete element, so in that case, we typically specify the strength of the rebar. So, that is nothing but the yield strength of the rebar, because we typically want our, we don't count on the additional capacity we get from the material for our design purposes. So, for our purposes or for our practical purposes, we just consider the strength as the stress at point B, because beyond that, it undergoes a lot of deformation, which is typically not something is desired from a structural standpoint.

So, therefore, point B is a very, very critical aspect of the stress and strain curve. And then, like point C is wherein, you know, we have the permanent set. So, the stress corresponding to the permanent strain is known as proof stress, and that is what is exhibited by this point C. And then beyond point C, we have the plastic behavior of the material. And then we reach point D, which is the maximum ultimate stress or resistance that the material can offer. And then beyond point D, once it's further overloaded, the material actually starts to reduce its resistance a lot.

And finally, it reaches the fracture point. So, this is the theoretical stress and strain curve, which we typically get. But given a lot of curvatures and all that we see over here, it's not a very, for our calculations in the design of steel structures or maybe RCC structures, like reinforced concrete structures, we typically want to always simplify our calculations. So, in that case, we look at the simplified or the idealized stress strain curves of different materials and not really consider a lot of these curvy linear elements because we have to, just to minimize calculation efforts here.

So, now let's look at the idealized stress strain curve. I mean, that's basically the simplified version of the stress strain curve, which is used in our design just to make the calculations very, very simple and also reasonably conservative.

Want the rest of Mastering Shear Force and Bending Moment Diagrams?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Mastering Shear Force and Bending Moment Diagrams course

The remaining 51 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Mastering Shear Force and Bending Moment Diagrams course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.