Lesson finished
Unlock all 48 lessons of Designing a Roadway Project Using InfraWorks, Civil 3D, and Map 3DFull course ₹40,000 · paid
Laying Out a Preliminary Road Alignment in InfraWorks
A free lesson from Skill-Lync's Designing a Roadway Project Using InfraWorks, Civil 3D, and Map 3D course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Conceptually Designing a Road and Presenting it Week 1 Session 3”
What will you learn in this free Designing a Roadway Project Using InfraWorks, Civil 3D, and Map 3D lesson?
The instructor lays out a two-lane component road in InfraWorks by placing points of intersection, then adds grass shoulders, 4 to 1 slopes and ditches. Curves are set to the 575 minimum radius for a 10 percent maximum superelevation, and a spreadsheet checks that the superelevation runout fits between curves.
- Placing points of intersection for a component road
- Adding shoulder, slope and ditch components
- Changing spirals to curves and setting 575 radius
- Checking superelevation runout between curves in a spreadsheet
What comes after lesson 3?
Later in Skill-Lync's Designing a Roadway Project Using InfraWorks, Civil 3D, and Map 3D course (paid): lesson 4, Conceptually Designing a Road and Presenting it Week 1 Session 4; lesson 5, Introduction to Civil 3D – Examining the Civil 3D Interface and Settings Week 2 Session 1; lesson 6, Introduction to Civil 3D – Examining the Civil 3D Interface and Settings Week 2 Session 2. The full course has 48 lessons (25 h 23 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Okay, let's continue on here. All right, so now that we kind of have looked at what we actually, you know, kind of our constraints and all that kind of good stuff, the next step is to actually lay this road out. And before we do that, I just want to point something out here. So one of the key things I'll just mention about InforWorks is it does have the ability to do super elevation. It just follows the AASHTO standards by default, but usually each agency will have its own set of kind of just a different version of the AASHTO standards.
Or, of course, here in a different country, it's going to be completely different standards and stuff. But one thing I just want to point out is this, is that basically what you need to do – now, I have a quick and easy way of actually doing this because – and when we get into the alignment section, I'll discuss this here, okay? But basically, this agency, the Florida Department of Transportation, has already provided kind of design criteria, and they basically integrate it with Civil 3D. They provide a state kit.
So, again, most agencies will do that, and if they don't, you'll probably work for a firm where you actually can have access to this data. If not, you're going to have to create it for sure. But basically, if you look here, just backing up here, so I've taken screen captures of all the different design speeds. And what does that mean? That means basically this. So, usually a road will be designed 5 miles an hour greater than what you're going to post. So, this is – we're designing this for 45 miles an hour, but they're going to post for 40 for obvious reasons.
You want to, you know, you want to be conservative and design your road a little for faster because, obviously, not everybody goes in the actual speed limit. So, what you want to know is you want to know what curves you're going to need based upon that super elevation rate and so on, what curves, what your minimum radius is, and that kind of stuff. Now, this is very preliminary, right? So, we're just – all I really care about, in this case, is my minimum radius. That's really all that I care about, okay?
That's going to be enough to kind of lay this road out, present it, and say, yeah, we can make this work. Obviously, we're going to survey at some point, and it's going to be something that you actually have to then get granular and actually see if those curves work. But it does give you an idea what the minimum radius is so you can massage and fit this alignment into the different parts of the actual – what you have for existing, okay? So, as we can see by this table, we're doing this for a maximum super elevation of 10%.
That's what this is in this kind of – for this type of road, okay? Minimum radius is 575, okay? So, that's just something to be aware about, and that's why I brought this up. Now, what we're also going to do is I have this spreadsheet here that does actually help me out in that it actually – I can define the different curves, and it already has calculations basically that say, okay, based upon the super elevation for that specific curve, what's the PC, the PT, and the point of curvature, point of tangency, where the curve begins, the curve ends kind of thing.
And then you have a specific transition runout that allows you to basically run out the super elevation. And we'll talk about super elevation in greater detail when we talk about alignments. I'll have some videos and some diagrams that show you exactly what the different locked-in kind of – or important stations are. The key thing to realize is that when you have super elevation around a curve, you have to have enough transition runout and run in to the next curve and the previous curve – or mistake – to the next curve and the previous curve that actually will allow a curve to run out.
Or if not, you can do an S-curve, but then you have to make sure that you can at least get to level crown, which is a 0% road, flat section of the road, that basically will allow it to then go back into the other curve if it needed to be, okay? So we're going to use this spreadsheet to basically go in and define the actual kind of run-in, run-out for each of the curves. That way we can actually see to make sure this alignment will actually work.
You definitely don't want to just lay out this alignment and say, oh, that looks pretty. We're good to go. I've had this happen many a time while working with other people and consultants and things like that. And they just lay it out to look pretty. And I'm like, hey, have you checked your super? That curve is not going to fit. We actually – you need to increase the radius. You need to either decrease or add a tangent, which then, of course, you now have more right-of-way than you might have to take and all that good stuff, okay?
So we're going to keep these two things up for now. The first thing I'm going to do, though, is I'm just going to start laying it out based upon what we discussed before as far as, you know, tying into the existing road, the utilities. That's the key thing. And, of course, all the different wetland areas and that kind of stuff, okay? So the first thing you're going to do, you go to the Create tab here, and we're going to lay out some roads. And we want to lay out what's called a component road, okay?
So I'm going to go ahead and click on that. And you'll see here, if I look here, it starts out with this basic two lanes. But just to point this out, if you click on this right here, you'll notice that this asset card comes up, and you can basically do whatever kind of road you need to do. You notice how I have a filter going on called shoulder. If I get rid of that filter, you'll notice that you can basically do – you can add any kind of road.
There's tons and tons of roads. And because our model – I said use all because I don't really care. It actually has UK. It has, you know, different standards from different companies like Sweden and that kind of stuff, okay? So, again, to just kind of minimize what I wanted to see, I just typed shoulder in here because I wanted to make sure I have a two-lane road with a shoulder. And I just basically just pick on that two-lanes road right there, okay? All right. So, again, we want to tie in here.
Again, I'm right-click dragging. That pans, all right? It's not like AutoCAD, which we'll get into, but it's not like AutoCAD. You have to right-click the pan, and then middle button actually goes up and down. You're really never going to use that one. Left-click, though, rotates the view, okay? So – and, again, you can lay this out in any view. That's the really nice thing about it is you can kind of look in 3D to kind of see how your road should be. So I'm just going to go ahead and click on the existing road here.
That will start it somewhere near there. Again, this is conceptual design. We're not going to be snapping or going kind of crazy, okay? So I'm going to go ahead, and because we know we're going to avoid these utility poles here, I'm just going to kind of pull it, you know, over here. And we'll just go over here. And what you're kind of doing is you're actually defining the PIs. Now, based upon what we know is going to happen with this road, we can't have this curve.
I've got to – you've got to fix this. So we're going to have a big radius that comes around here, then ties back in here. So I have two PIs, points of intersection. So I'm just going to go ahead and click over here, and I'm going to just click over here. Again, we're going to modify this afterwards, but we basically want to just kind of get it in there as a starting point. So, again, I'm noticing these two utility poles here. I'm going to click here.
And, again, you can rotate the view and see, okay, if I click over here, that gives me some more room to kind of pull the road on the left side here, because now the utility poles are on this side of the road. So I'll just click over here. The other thing I'm keeping an eye on is the parcels because, again, we want to minimize the right-of-way. We don't want, like, a little sliver of right-of-way being taken here and then here. You want to basically pick one side, whichever one is the least impactful to residents.
In this case, you can see there are two houses here, right? This is some woods. So a property owner is going to have a much more – be more acceptable if you say, hey, we're just taking this frontage here. Your house is not going to change. Your driveway is going to be upgraded when we put the new road in. So, you know, don't worry about that kind of stuff. So basically that's what I'm going to do is I'm going to rotate in this view here. And I'm a little bit off, but I'm not going to worry about it too much.
I'm going to basically pull this in over here, but I'm going to stay on this side because, as we said, the utilities are on that side of the road. So we'll go ahead and click here thinking, you know, again, I'm envisioning a PI, point of intersection. And, again, we've got the same thing here. We've got the poles. Now, if you look here, the poles actually, they do – mostly on this side. This is probably just a utility pole that is a service one that goes to this cell tower right there, okay?
So, again, there's – you know, I'm going to try to avoid this, but I'm going to be taking probably this pole out because I'm going to have to – this curve looks too sharp. I bet you it's not 575. So I'm going to actually have to kind of pull the curve over here. We're probably going to lose that pole. But, hey, we're minimizing the poles we have over here. So I'll go ahead and just click. Let's pull this back in kind of the top view. And we'll go over here.
And then we'll go look over here. And, again, we've got the utility poles on this side. But, again, we're back to this part here. I'm going to try and minimize what I take. So let's actually pull the – we'll put the road actually over here because, again, my PI is going to be – it's going to take out this pole, I'm sure, but that's fine. We'll just put it over here, thinking that's where my PI will be. And then we'll just kind of pull this back up.
And, again, if I look here, we've got the utility poles on the left side of the road. And, again, I want to minimize right away. And so I also see this little pond here. We want to stay away from that. Of course, the utility poles are here as well. But this looks like all woods, not a big deal. So we'll go ahead and kind of – I'm going to put a small PI over here just to get the road over here. But, in the end, it's just going to be one PI.
So I'll just kind of pull this over here, following existing. All right. Now, again, holding this side for now, we'll just go and go over here. But, as you can see, I do have this issue here where I'm going to have it – you know, for whatever reason, it goes to the other side of the road. Actually, it does it over there. There we go. Yeah. So there's that utility pole. So I'm going to kind of try and sneak in here, and we'll just basically put this over – let me see.
Let me bring this back to top view. So I'm coming from there. I want to kind of pull it this way. A tiny bit, I'm going to pull to the left here, like so, and then I'm going to have to go pull this back in, right? And it looks like here, yep, there's not much I can do about this one because all the poles are on this side, no matter what. Again, these are the things you have to kind of think about. Depending on the county, depending on the agency, everything, it may actually not cost the county anything to relocate the utility poles.
In fact, it may be on the utility company because they are using the right-of-way for free kind of thing inside the agency that if the agency does something to the road, it's on them and doesn't cost anything. Now, of course, as a good servant of the road, you're not supposed to, like, you know, impact their utilities too much, okay? So in this case, though, the county is actually responsible for the relocation of any utility poles, so we're trying to minimize that. So right-of-way is probably cheaper than it is to relocate these poles.
Let's say $3,000 or $4,000 a pop when you're only paying maybe a few hundred dollars per acre. If all you're taking is one or two acres, then you're minimizing. That's still cheaper than actually relocating utility poles. But, again, these are things you kind of just have to think about. All right, so I'm going to basically pull this back in. Let's go back into top view here. And I'm going to assume that I'll have a PI probably, like, over here. And now that should line me up nicely.
Yes, it does with this part here. I've got a little bit of a floodplain area here. I can almost guarantee you we're going to have to have a floodplain compensation pond over here. So we're going to have to have some right-of-way. That's okay. Nothing spectacular there. But I'm going to keep on. As you can see, I've got this pretty good straightaway here. You know, again, once you get granular design, you may have to actually add some really large radii curves in here to kind of straighten out the road.
Or, depending on the design standards and speed, you can actually add a PI that has a minimum deflection angle that basically the driver wouldn't even notice that they're kind of changing direction. All right, because roads, not all roads are obviously really straight. It depends on the history of the road and stuff. So, again, I'm going to basically hold on this side to minimize what land we are going to take there because the utilities are on this side. I've got this little pond here. I've got to worry about that.
I've got another floodplain compensation area that I might need. And I'm trying – if I can avoid that, that'd be great because, again, that's additional right-of-way, additional construction. I don't want to have to kind of worry about. Okay, so we'll go ahead and just kind of pull this in again. Now I've noticed that the utilities are over here. So – and I do have a property owner. That's okay. We'll just kind of pull it over here. I'm going to go start over here, and then now I'm going to have another PI going over here.
Now we're entering this really large floodplain area. That's okay. We'll try and minimize it because I think at this point – yeah, I've got the bridge coming up. We should be unexisting. So if that's the case, that we hold existing, we're going to have a minimum fill footprint. I'm just thinking ahead because when you're basically holding existing ground as far as in your profile view, well, you're going to raise it above where the lime rock is, the optional base, your subgrade basically. So that will be raised – that will be like a foot above.
I'm envisioning I'm probably going to have a foot of basically 9.5 inches, 9 to 10 inches of optional base group, which is lime rock kind of thing or sub base. Then we're going to have 2.5 inches of pavement. So that's 11.5, so let's just go with a foot. We'll just assume a foot kind of of that. So if that's the case, basically I'm going to probably have a more larger amount of cut, especially if I'm unexisting, with ditches than I am of fill. So as long as you're in cut in a floodplain area, they're okay with that.
You're actually – again, think of the glass with the ice cubes, right? You're actually – imagine you're just – you're suctioning out water because you're taking away area or you're actually increasing area as long as you're above the seasonal high water table. And, again, we would get borings, not for the whole job. Some jobs actually might require that, but we'd probably get borings just for the ponds. But maybe we'd get some like every 1,000 feet for the road. That way we can kind of see exactly what's going on with the road, okay?
All right, anyway, so let's see what we've got here. So now I've got to tie back in. And so I'm going to kind of pull this in over here. Again, it's a little modified afterwards if you have to. And then, of course, with this, I'm going to go all the way down. And we actually – the paving patch is somewhere up here. For now, I'm just going to kind of just tie in to the bridge because we actually have to tie into the bridge. We're going to replace this with a box culvert, brand-new box culvert.
And I'll just click over here. There might be a PI somewhere in here. I'm kind of looking at the road a little bit. Yeah, I can see that the PC kind of starts over here. But we'll just put it in there. And then I'm going to end it. There's my pavement patch, I think. It's okay if it isn't. We'll adjust it eventually. And I'll just double-click. So to end an alignment, you double-click. All right, and then it updates the model and does the default kind of settings based upon that type.
So in this case, we've got, you know, a road with, you know, some shoulder in there, and it's going to daylight and so on. All right, so let's go ahead and set – I'm going to go back to home view here so we can actually – mistake. All right, so actually I forgot I reset the home view. So that's okay. We'll just – I'll just zoom out here, and we'll just kind of fit that in there. Okay, now, going back to where this begins, let's start taking a look at fixing up this road, making it look pretty, and doing what exactly we want to do with this.
All right, there's our tie-in to there. As you can see, Infoworks automatically does it, which is really nice. I'm going to go ahead and pick the road. So the way this works in Infoworks is this. You select the road first. That picks – that gives you, like, your stationing, the whole road, and then you get kind of things that you can change here. Then if you want to pick individual things about the road or components or the alignment or the curve, you click on that specific part.
So if you look here, if I click on here, I now have picked that component, right? Whereas if I pick on this one, I pick that component. If I pick on this one, I pick that component, et cetera, right? So what I want to do is I'll kind of zoom in here. Let me just hit Escape once. That gets me back here. And it looks like I actually do not have the shoulders. I thought that I actually should have added the shoulders. It must have just been a two-layer number.
That's okay. We'll just select this here. And what I want to do is I'm going to right-click, and I want to insert a road component. We'll add the shoulders, okay? It looks like that component, for some reason, didn't have it. So I'll just go in here. If we look here, if I scroll down, here's a shoulder component assembly. Notice that when you hover, you simply, you know, Infoworks knows where you are. So I'll just go ahead and click over here, all right, and it just adds it.
And that's okay. I don't really care how it does it because here's the cool thing. I'm going to click on this. I want that to go to the start of the road, and that just goes to the start of the road, okay? And then you click in Space to kind of update it. And then I'll click on this grip here, and I want that one to also go to the end of the road and click in the model. And now you can see I basically have it in there.
Now, of course, yes, this did overlap here. We can move it afterwards. I'm not too worried about it, okay, because we just want to kind of see, you know, we're just going to lay this in here. When I go through the visualization part, maybe I'll make it look a little prettier. All right, so for now, I want to actually make this a grass shoulder, so I'll click on this here. And you'll see we have some options. If I hover, it tells you what it is. So that's manicured grass.
And now that will update. All right, so that looks kind of nice. And then we'll click the road one more time. So I'm just doing Escape in between, just so you know. And I want to now right-click, and I want to add the component on the left side of the road here. So we'll go ahead and just click anywhere. It doesn't really matter because InfoRocks provide these really nice tools. So just click over here, and then we'll go to the Start, click. And then if you click on the other grip here, we'll go to the end.
And, again, you'll notice you have this tip. It says you have one more edit on the component. Click outside of the component to refresh it. That's kind of it does give you these nice little tool tips. I still have it selected, so let's make this one here grass, right? And now that will update. And I'll just press Escape a couple times to kind of see what we've got in here, okay? So as you can see, we've kind of got it going on. And, yes, we know we're going to have some issues here.
Again, this is a conceptual layout. We're not going crazy right now. The goal is to show this is doable. Here's what we think is going to happen. And then to get approval from the different agencies and so on to say, yep, that looks good. Or, hey, we need you to minimize this. There's no way we're going to do wetland mitigation in this area. So whatever it takes to move that row, change the radii, whatever is involved, okay? Let's go ahead and click on this one here, all right?
And I want to actually change this to also be, when it's in cut, I want it to be a grass material there. That's fine. And when it's in fill, I want the same thing as well, all right? And that way we can see that. And we also do not want a slope of three to one. So I'm going to go ahead and click inside here. Once that's done, we'll change this to four. And we'll change this to four as well. All right. So that's a standard, whoops, mistake there.
We'll just click once and do four. And now that should update. All right. So I'm just pressing escape here to kind of get out of that. And you can see it's kind of updating very nicely. And we'll just click on that one again. And we'll change this one to grass. Change this one to grass. And change that to four. And change this to four once that's updated. And change this to four once that's updated. And we're just clicking space here and that updates everything. Okay. So we're still not done because basically we do not want to have water collecting or going where it's not supposed to go. This whole road is a very wet road. And what that's going to require is basically ditches to carry the water to all the different spots. We don't want the property owners to get flooded. That's the thing you always have to think about. So I actually need to add another component. I want a two foot ditch.
So what that requires is an additional slope at four to one. Basically, if I do four times two, that's eight, right? So I need a width of eight feet and that'll get me to my bottom of the ditch at four to one. So I'm going to go ahead and right click here and we'll go ahead and click on insert road component. I'll scroll down here. I'm going to pick the shoulder one. It doesn't really matter. You'll see why in a second because you have all the different options to do whatever the heck you want with this. So I'm going to go ahead and click on this here and we'll do the same thing we did over there. We'll do start a road.
Click in space. Click in space. And then we'll pick the end of road. We'll pick that grip and do end of road. Click in space. I want this to be grassed. And what I want is I need this to have a width of eight feet and a slope of negative 25. All right. So that'll give me my ditch no matter what. And I also forgot here. I got to check this one. So this one here, I actually want this to be, I forgot to change this. This is our shoulder.
So this will be negative six percent. And I, we have a, per this standard, it's a width of six feet. Okay. All right. So we're kind of starting to see things shape up very nicely here. So I'll just click on this shoulder as well. Again, click the road once, click that component and we'll change this to six. And I'm just clicking once here. Kind of, it's nice. It just pops up. We'll do this at negative six and I'll pick my road again, right click and insert road components.
And we'll again pick that shoulder. We'll just go to the left side here and pick this. We'll go to the beginning of the road and pick this and go to the end of the road. And we'll change this to that nice grass. And this here should be a distance of eight feet at negative 25%, which is four to one. All right. So just press an escape here. We can kind of see that it's actually, that's very nice. So then from here, we want daylighting. So, and basically we're going to make it so that we can get a ditch here.
That's the whole point. And Moomer and Phil, it's okay. We know that we're going to have a ditch. This is just to give you an idea, basically what we have to do. As you can see, mistake. As you can see, Infoworks, you know, it does its best job here to kind of put a profile in. We can adjust that. We can change that. And we will. Okay. We will definitely take a look at that. The first thing I want to do, though, is I want to actually, as per our design speed and our max super elevation of 10%, we need a radius of 575.
So we actually have to fix these first. Okay. And as you can see, that basically has like kind of an S curve here. And what we're going to have to do is we're going to have to make sure that we actually can have a super elevation transition out. So we have to actually have to make sure that that's actually going to happen. So we need to, let's, let's just change this and see what happens. So let's go ahead and click on here. That's the first thing you do. Then I'm going to go ahead and pick on the radius here or the curve.
And you'll notice that it actually is showing me all the different parts here. And so this one here, I need to convert this to a curve. This is a spiral. We don't want that. So we just make that a curve, you know, to spirals in the United States. And so now if I go ahead and click on this here, my radius is 144. So I need to click over here and change it to 575. Once you do that, radius violates supported geometry. And what we notice is that this is actually not working. So that's okay.
So basically we just kind of have to figure out what's going on here. So what is probably going on is that this radius, it says 543. It cannot fit between here. Here we got plenty of room, but it's going to split, you know, 575 both ways. So we need to get rid of this curve here real quick. Let's actually convert this to a none. And that way we actually now have plenty of room to work with, or we should. And let's change it on this here. Let me pick that again.
And we'll go ahead and click on this and we'll change it to 575. And this should work. We'll see where it actually runs out. And as you can see, it's pretty close. So we're not going to fit another 575 over here. So what we got to do is basically we got to pull this PI here and get the curve starting a little earlier. And again, that's just what we're doing here. That's what needs to be done to fix this road. So I'm going to go ahead and let's go back to the top view here.
We can just pick this PI and we'll just kind of move this. Notice how it's maintaining that. I want to kind of keep the same tangent and we're just going to pull this back. And like I said, it's just going to start the curve a little bit farther down. All right. So let's just look at that. And we're still pretty much away from the utility poles. Once we reach that profile, I'll bet you it will be actually even better. And so that's okay. So now we've got that in there.
Now, let's go ahead and go over here and we're going to go ahead and click on this. And I need to right click over here and convert the geometry to a curve. And let's zoom in there. And that all looks good. And now we'll click on this one here. And let's hope we should be okay. 575. Press enter. And it does actually fit it. But here is the issue. Not the issue, but just something you have to, you know, to look at. And we're going to look at this right now just so you get an idea.
So basically I've got these two curves, but is there enough tangent runout to actually run this out and then run it back in, right? Because we have a left hand, we have a right hand curve going right. So that means this side of the road is going to be picked up. And then in this one, you have to basically have enough room to run out. Okay. So we're going to go back. So while we have this, you know, alignment selected here, if I go over here, I'm going to go pick on this first curve.
And we actually want to, I always just type this in here. And we'll just type that's the radius that we have. And what's our super elevation slope ratio per the standards at this design speed? It's 200. And our super elevation is 10%. And what's our normal crown? Negative two. And here's where you need to actually know your PC and PT because it does the calculations for you. Okay. Now this spreadsheet, of course, will be included in your assignment. So you'll be able to fill this out.
No problem. So I can see here, begin curve, end curve. And so let's go back to my Excel spreadsheet here. And my begin curve is going to be at 909. We'll just do 910. That's fine. We'll just round up. And the end of my curve is going to be at 1352. So 1352. All right. Now, when you do that, you'll notice that this actually, what percent on transition do you want? Typically, they like it to be more transition on the tangent than on the curve, right?
That way you smoothly come up into super and then you're already in super like, like, you know, right here. Now that will cause a problem though, because obviously the same thing will occur at this curve. So let's just pan over here. And then let's go back to my spreadsheet here. This one is also going to be a 575. So we'll click over here, 575. And then if we go back here, so the same thing. And we have 10%. And that's our normal crown. And our PC station is 1510.
So 1510. And then my end curve is 1888. So 1888. All right. So now I've got this. So here's what you look at. So where does this thing get normal crown? So 1563. That's my normal crown transition out. Now, if you look at 1563, that's somewhere already inside this curve. You see we have actually an actual problem, right? So what we can check is where's our zero cross slope? It's at 1519. If this zero cross slope is at 1520 or 1519, we're good. That's okay. You have enough tangent for it to run out, basically go from one transition right to the other one.
But if we look here, I can almost guarantee it's not. Yeah, zero cross slope is at 1343. That's actually, we have 200 feet we've got to think about. So what you can do, most agencies will allow a 50% on the curve, 50% on the tangent. So we're going to change that. Let's see what that gives us. So if we look here, my zero crown is 1440, and my zero crown here is 1422. That's a 20-foot additional that I need. And that's okay. So you know what?
I'm looking at this, and if I were to pull this back 20 feet and pull this up 20 feet, you know, if I just, in fact, I could do probably all 40 feet right here. If I just pull this this way here, you know, 40 feet, I'll bet you if I were to redo that calc, it would work. Okay? So doing that just as a, it's a nice spreadsheet to have, and I'm basically good to go. I can kind of tell that that's actually going to work out just fine.
Okay? That's probably going to be the only issue that we have. There might be another one by the other intersection, but that's basically, we can kind of see that that is going to work. Okay? So just following along here, we'll go ahead and click on this here, and we'll right-click here, and let's convert this to a curve. And so we know our minimum is 575, but it doesn't mean we want 575. You know, if you can avoid having to do that, we will. So let's make this one, let's say, like 1,000, or actually, let's make it 2,000.
That makes a nice flat curve, and actually, that looks really nice. And so obviously, the more you do design, you kind of get the hang of, okay, what radius can this kind of area, you know, do, and what do I need to actually have? Now, I do see a possible. Where the end curve is here. My transition out is probably going to be like over here based upon that. So we might have to change that radius. So we'll click on this one here. Right click, convert. We'll do curve. Again, I'm going to try and minimize this one. So this one here might be a 575 one just to kind of get that in. That actually looks pretty good. I'm going to probably shift this up a little bit. I want to make sure that actually this looks really good.
If I can get that to work, I'm going to probably keep that. Because if you look here, I'm avoiding that utility pole, avoiding that one. This side here, though, oh, we've got three poles we have to worry about. So I'd rather take out one than take out three. So, you know, I'm going to probably take this PI here and, you know, move it down this way. And I may even take this one down here as well and move that down. There we go. You can kind of see I'm still in here. Again, this one avoiding, we're going to affect this one. That's okay if we can avoid three, you know, hitting three.
Now, again, that said, this one we have to fix, right? This one's pretty important. And so if I go over here, we're going to right click on this one. Oops, let me pick the curve. Right click. And we want to actually convert this to a curve, not a spiral. And for this one, we'll click that curve again and we'll click over here. And I want this to be 575. Press enter. Oh, can't be supported. So what that's telling me is I can't fit this in here. Let's just pull this up here.
That's the first issue. And we're going to get rid of that PI later on. But there, I should be good if I click here. 575. Oops, let's pick over here. 575. Press enter. There we go. And now you can see that that's, you know, again, I'm trying to avoid this. It's going to be kind of impossible. I may actually have to just pull that down here. So if we pull this PI and again, you do your best. And basically, you kind of do the best you can and see what you can avoid and what you can't avoid.
And it's going to be that simple. So I can just take that one out, not three. And yeah, so that's fine. We know we're going to have to lose that one. And this one here, there's no way I can really snake that in, right? Because based upon this, that's a minimum of 575. And I still see another issue here as well. You can kind of see. So here's, let's just do this again. And this is, I know I'm skipping curves, but I'm pretty sure that my tangent run out and run in, yeah, those are plenty of enough room.
You know, if I check my transition length at 10%, you can see that real quickly, it's 264 feet, right? That's basically, that's for any curve, right? So that's a maximum of 10%. If I have a super elevation rate less than that, you know, it's going to be less than 264 feet. So I can just kind of, you know, eyeball this and say, okay, let's see. So if I've got, you know, if I'm coming out of this curve here, so we know, there we are. So we're coming out and we're basically at this one. We're actually at the end.
So if we go to curve two, it's going to be at 2020, right? So right here, do I have 260 feet, you know, to get, let's say this was 575, but it's not. I'm going to have one, two, I got 300 feet. So we're good there. And then do I have 300 feet afterwards? So this is going to be, so that was 240. So past the curve, 240, that's at 50%. So it's probably a little more. So this one I'm actually going to check. I want to check this one here, okay?
Because this one's getting kind of close. So what's my radius for this one? This is 2000. In fact, actually, I guess what we could do too, let's actually make this 1000. All right, that'll actually shorten the curve up quite a bit. Yeah, that's actually really good. And then if I look at my table for a thousand foot curve, you have a super elevation of about 7.5%, right? We're somewhere in between here. It's guessing is good enough for this. We're estimating. So it's 7.5%, okay? So let's go ahead and go back to our spreadsheet.
We'll go to curve three and we're going to be at 7.5%. I'm going to type that in before I forget it. And my PC here is 28.90. So it's 28.90. And my PT is 32.23. So 32.23. And I'm going to leave it at 80%. And we can see the transition right now. It's 33.90. So we're actually at 34. So that's right there. We're plenty good at this one here. In fact, we can tell for sure we're definitely good with that one. That was actually a good way to actually do that.
Now, this one here we definitely have to do. So this is 5.75 and so is that one. We've got the same kind of situation over there. So I'm just going to go over here. And again, I'm not really kind of – this is just a quick way to kind of get this done just to make sure that we actually can fit this all in. And my PC here is 38.80. So 38.80. And my PT is 4151. We'll keep it at 80% for now. I know that's not going to work, but that's okay.
And this one here, if I go over here and let's go to curve 5. And this will be at 10%. That's already there. That's good. And this one's going to be actually at 44.12. So 44.12 and then 5206 if I'm looking up there, 5206. Okay, so looking at this first curve, we can kind of see what. So this ends – normal crown ends at 43.62. So 43.62, I have to – that's what I need to actually have. And if we look here, I've got 4201. So that's not going to work.
However, let's look at what level crown is. 43.18 is level crown for this one. And level crown for this one is 42.45. It's still not going to work. So let's change these to 50% again. And I could try to play with these numbers if I go 70%. That might work. But let's just do the – if we have to, just do this. So that's now a 4283. And, oh, we're really close. In fact, basically, that's actually – I'm going to go with this because what I could actually do is all it requires is I move this alignment three – or this PI three feet this way, and we're good to go.
Right? Again, this is just a conceptual design, so I'm just estimating. So we know this will actually work, and we're good to go. Now, let me go ahead and – let's see. Do I need that point? I don't need that point. Let's go ahead and right-click on that. And – whoops. Let me go back here. And we'll just go ahead and select this, and then right-click here, remove point. That's how you kind of do that. Okay? And we'll adjust this PI to basically pull it in.
I need to kind of pull into this point right here, right? So we'll just pull this in here, and we'll look at it afterwards. That's fine. And we can kind of see that we're into – you know, this actually might be enough of an offset. Again, we're really low here. You can kind of see it's kind of going below the existing ground. Once we change that profile, I'm not too worried about that one. We can adjust it afterwards. But let's just kind of verify that we're still good here, and we are.
Actually, we're doing really good, although we have a pond going on over here. We're probably trying to leverage this area to put a pond in because we're going off the existing road, which means you have to have a pond to treat this impervious area. And this actually is looking really good. We know we're going to hit that one. That's fine. This is pretty clear, and so that actually looks like it actually may work out there. Okay? All right. Let's take a little break here, and when we come back, we'll kind of finish up the roadway.