Lesson finished
Up next: Cracking Moment and Ultimate Capacity of a Concrete Beam in Excel
Unlock all 48 lessons of Design of RCC and PSC Superstructures using LUSASFull course ₹40,000 · paid
Concrete and Steel Basics for Bridge Design
A free lesson from Skill-Lync's Design of RCC and PSC Superstructures using LUSAS course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Bridge Concrete Superstructure Design”
What will you learn in this free Design of RCC and PSC Superstructures using LUSAS lesson?
The instructor covers what concrete is made of, the hydration reaction, cement types and admixtures, and why 28-day strength is used for design. The lesson then compares cube and cylinder tests, concrete and steel design curves, and uncracked versus cracked beam behaviour.
- Cement, aggregate, water and the hydration reaction
- Water to cement ratio and 28-day design strength
- Concrete and steel stress strain design curves
- Uncracked versus cracked reinforced concrete sections
What comes after lesson 1?
The next free lesson is lesson 2, “Cracking Moment and Ultimate Capacity of a Concrete Beam in Excel” (25 min). Later in Skill-Lync's Design of RCC and PSC Superstructures using LUSAS course (paid): lesson 4, Skill Link Course on Bridge Superstructure Design; lesson 5, Performing Analysis and Adjusting Beam Dimensions in Simulation; lesson 6, Structural Checks and Calculation of Ultimate Capacity. The full course has 48 lessons (22 h 51 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello and welcome to this Bridge Concrete Superstructure Design course from Skill-Lync. This is week one and today we'll cover some concrete design basics and bridge form selection. To briefly go through the content, we will look at concrete as a material, we'll remind you and refresh some of the knowledge you might already have about concrete design and the basis for concrete design. We'll look at the design of rectangular sections and we will see how concrete basics are applicable in bridges specifically. We will then move on to cover some basic bridge forms and how different bridge forms can be achieved with concrete.
So, let's start by talking about concrete as a material. From your previous experience or from university studies, you might have already come across concrete. as a structural material, but I will go through it anyway because everybody might be at slightly different levels and quality of previous education might differ. First of all, let's look at what concrete is made of. At its most basic, concrete is made of cement, water and aggregate. Cement and water are mixed at different proportions to make cement paste. Cement paste acts as a glue which holds loose aggregate together to form a homogenous mass.
Cement is made of limestone and clay minerals that are heated up and ground into what's called cement powder. You can have a look into the production of cement on the internet. There are some really good materials available. But you will often find that it's widely available in local shops, in construction suppliers Here is a nice visual diagram to explain how concrete reaction works. When cement powder is combined with water, a hydration reaction starts. It's important to understand that the concrete doesn't simply dry out. It does not lose water.
It, in fact, absorbs water to form cement paste. And cement paste acts as a binder with the aggregate to form solid concrete. So aggregate works as a filler, creating big grains inside the concrete mass. And cement paste glues it together to give it some of its sheer and tensile properties. But let's look closer at the hydration reaction. As well as cement paste, the hydration reaction produces a lot of heat and also alkali, otherwise known as lime. Heat must be carefully managed in concrete reaction. It may be good in cold weather.
And sometimes you will find that you will need to keep the heat in the concrete by covering it in colder climates. In hot weather, excessive heat can generate very fast hardening reactions and some cracking. You must also manage heat with larger sections. The bigger the section of concrete, the more heat it generates. And differential heating between different parts of concrete can also lead to cracking and other adverse effects. Alkali give concrete its durability. Concrete has a relatively high pH value, which means it's not very soluble in water, so it's good at resisting weather.
And it also fares well against acids. In fact, when exposed into the atmosphere, concrete reacts with carbon dioxide in the atmosphere through a process called carbonation. So over time, the surface of concrete becomes more acidic than the inside of it. Alkali are also quite corrosive to skin. So when the concrete cures, you must be very careful not to touch it and make sure that the workers on site do not come into contact with wet concrete, because it can cause skin burns. Alkaline concrete can also react with silica and other minerals in atmosphere, in groundwater or in soil, causing concrete deterioration and other problems, such as concrete cancer, which I highly recommend you read about in your spare time.
Another common element of the concrete reaction are chemical admixtures. They are added to the concrete mix in order to alter the hydration process, otherwise known as curing. Some admixtures accelerate the reaction, which speeds up the process but generates more heat. This is sometimes useful in really tight construction programs to speed up the process on site. In contrast, some admixtures are added to slow down the reaction in order to control heat and prevent cracking. Other types of admixtures can be added to alter physical properties of concrete, for example its workability, or how fluid it is, or compaction, which can greatly enhance progress and quality on site.
Now, let's look at different cement types. The most common cement type is Portland cement. Portland cement is named after a similar looking stone which can be found in the Isle of Portland in the United Kingdom. Since being invented in the early 19th century, Portland cement has rapidly become a very common construction material. But it's not the only type of cement used out there. There are other variants available on the market. For example, rapid hardening cement is also widely available. It's made by grinding the clinker into a much finer grain, which has a larger surface area and the chemical reaction happens much faster.
This has similar effect as adding admixtures, as it accelerates the process and also generates more heat. Rapid hardening cement can be used on construction sites where time is of essence. It is also very popular for pre-casting yards, where fast production times mean better profits. As mentioned before, faster reaction times can generate a lot of heat and can cause cracking. So, control of environment and control of process are really important in using rapid hardening cement. Other types of cement include sulfate-resistant cements which have different chemical composition and they're better at resisting sulfates and other acidic substances which are commonly found in salt and water or underground.
When using cement in underground applications such as foundations or in marine applications, always consult with a relevant specialist because they will be able to advise you on the right cement type for a given environment. Portland cement doesn't always work in some of the specialized environments. And that's very important to understand when choosing a concrete mix. It's also very important to consider that cement production takes a lot of energy and generates a lot of heat and carbon dioxide, which is now a hot topic in the world with climate change and a strive for a more sustainable future.
Cement alternatives such as ground granulated blast furnace slag, or otherwise known as GGBFS, or pulverized fuel ash, or also known as fly ash, can be used in proportions with normal Portland cement in order to achieve a more environmentally friendly mix. GGBFS is a byproduct of steel production, while pulverized fuel ash is a byproduct of electricity generation. If a steel production plant or electricity generation plant are available nearby, this can reduce cost and improve sustainability of your project by reusing the waste from existing productions. It's important to note that they're not activated by water like cement, but they're actually activated by the alkaline solution generated by the concrete reaction.
So they can't really be used on their own, unless mixed up with normal cement. It's also important to note that GGBFS and pulverized ash slow down the reaction, which can lead to slower construction times. However, if carefully managed and procured, these alternatives can go a long way to reduce your carbon footprint. Now let's look at the other components in concrete production. Water is very important. Acidity and impurities can be detrimental to the concrete quality and strength, and can even lead to failure. Clean water must always be used for concrete production, but it's a precious resource and must be carefully managed.
Another thing to consider in concrete production is the aggregate. Both size and quality matter. Finer aggregates tend to give you more strength, because they have higher surface area, which bonds better with the cement paste, giving a stronger mix. Fine aggregates, like sand, are often used for grounds, which is a special mix that is used to fill in voids, for example, between two precast parts or between a bearing and a concrete part. Normal concrete uses a mix of finer and larger aggregates. Larger aggregates effectively create... Larger aggregates effectively create...
Volume for concrete, which is quite cheap, and the aggregate is generally cheaper than the cement itself. The maximum size of aggregate is governed by the workability of concrete, because concrete must be poured. You cannot use very large aggregate, otherwise it gets blocked between the reinforcement, and it can't access tighter spaces in the formwork. The typical maximum size for aggregate is 20 mm, although smaller maximum size of 10 mm is often specified for tight areas and highly reinforced concrete parts. Extremely fine particles should not be used as aggregate. For example, clay makes concrete mix very soft.
It is sometimes used for specialist applications, such as suspensions in piling operations like bentonite, and sometimes clays are used in heritage applications to restore old buildings, which require the ground or mortar to be very soft. However, in general, and in most applications, you want a good mix between larger particles like gravel and finer particles like sand, to give you a very good, fluent, and versatile mix. The quality of aggregate also matters. Brick rubble and organic materials such as coal and shell do not make a good aggregate, because they tend to decompose and break, making concrete very weak.
Ideal aggregates are nice, hard stones. In general, the concrete manufacturers and national standards cover the selection of materials for aggregate really well, but when you are on site, and if you have a site roll, do make sure that no corners are cut, and that the good quality aggregate and good quality water are used. I have already mentioned our mixtures in previous slides. We have discussed accelerators and retarders to manage the concrete reactions and to manage the heat generated by concrete reaction. There are also admixtures called plastifars, which increase workability, and sometimes aerators are used to give concrete some frost resistance and prevent brittle failures.
Now that we have discussed how concrete is made and what it is made of, let's talk a bit more about concrete properties. Chemical composition is very important. As engineers, we don't tend to look into it too much. As engineers, we are mostly interested in concrete properties. Unlike other construction materials like steel and timber, which arrive on site with final properties, concrete is often poured in situ, and its strength develops with time. When the concrete is just poured, it has zero strength. It relies purely on the formwork that supports it in order to hold it in place.
But it quickly gains strength, with a lot of strength gained in seven days, and 28-day strength is typically used for design. It's important to understand that the concrete strength develops for a very long time afterwards, but the rate of increase is very small, and 28-day concrete is generally a good benchmark for use in the design. You must also understand that the strength of concrete is highly dependent on the water content. It is often expressed in terms of water-to-cement ratio. Water-to-cement ratio is the weight of water divided by weight of cement in a cube of mixture.
Note that this is a weight ratio, not a volume ratio. A ratio of 0.25 is required for hydration to begin, because cement requires water for the reaction to occur. But the low water ratio like this won't give you a good concrete. It will be very strong, but will be very difficult to handle and pour. It won't be very workable. So typically, on site, you will see that a ratio of 0.5 is used. Ratios between 0.4 and 0.6 are often used on site, depending on the requirements.
And increased water content will increase the workability and make concrete easier to pour. But reduced water content can increase strength. Although strength is very important, it's not the only property that we must consider when choosing the right mix for the site. As engineers, we often look at stiffness, which affects how much the structure deflects and vibrates. Density, which affects how much the structure weighs. And durability, which is increasingly important in consideration, because that defines how long our structure is going to last, and how expensive the repairs are going to be in the future.
There are other important engineering properties related to long-term effects, such as creep and shrinkage, which we'll cover later in the design course. As well as engineering properties, there are a number of construction properties that we've already discussed, that the contractors on site will be very concerned about. For example, workability, or how easy it is to pour concrete. Rate of hardening, which is also related to the heat generation. And for colder climates or mountainous climates, frost resistance of concrete is also very important. And of course, for your client, or for the government, or whoever pays for the project, the cost is very important.
And for society in general, sustainability and aesthetics are also important considerations when picking the mix. As you can see, there are a number of factors to consider when choosing the right concrete mix. But as engineers, we can't worry about all of them at the start of the project, especially when there's so much uncertainty in the concept design, and we don't know the site, and we don't know the project that well. Fortunately, in terms of engineering properties, the codes give us a good guidance. Most reputable codes define concrete in terms of strength classes.
As engineers, we often simply choose the strength class that we want, with all of the engineering properties tied to that strength class. In some specialist applications, like megabridges and skyscraper design, you might also choose some constructability and aesthetics criteria. But in general construction, we leave those properties for the client and for the contractor to design on-site. What we choose as engineers is the strength class. Indian codes and Euro codes define slightly different strength classes, and you must understand that. The strength classes are defined from standardized concrete testing, such as the one shown on this picture.
The value is expressed in megapascals, and it represents a stress that is roughly required to crush a given specimen of concrete. For bridges, you will typically specify between 30 and 50 megapascals of strength, although higher values are increasingly used in especially long-spun bridges, where weight is very important, and you want to achieve more with less concrete, which will save your material and save on the foundations. But we'll cover that a little bit later. Before then, it's really important to understand that some countries' codes, and even in the same country, the specimens are different.
Indian codes and the old British standards use cube tests, while the Euro code and US standards use cylinder tests. The cylinder strengths are related to cube strengths and really well correlated. However, the concrete tests tend to give you a smaller number of megapascals, because it's a taller and more slender specimen, while cube gives you a higher strength, and it actually involves some friction, so it's not the best way of measuring concrete. However, in practice, that rarely makes any difference, because different codes of standards, although they use different tests, they will use slightly different factors as well to achieve the same value of real strengths on site.
So, it's not something that you have to worry too much about, but definitely be aware that that is the case. And if you're working abroad, or if you're working for an overseas company, that's something that you definitely need to know. Now that we have discussed how the testing is done, we need to understand how it actually relates to reality. So, when these concrete specimens are crushed, what you will see if you plot the deformation or the strain, which is deformation of the lengths, to the mean strengths, is something like this graph.
For different concrete grades, you will have slightly different behavior, and you will find that for some very short period, the concrete will behave elastically, so as you increase the load, the deformation increases proportionally. But at some point, the concrete starts to to deform much more rapidly than it's loaded. At some point, it will give, and it will crash, or it will start plastifying. Now, this is a very scientific representation. What we use in the design is often quite more simplified. Most cores define this design curve, which is similar to the blue dotted line in the graph.
For smaller strains, so as you're loading the concrete a little bit, it will follow this non-linear path, and once it reaches the limit of its strengths, it follows this very linear path. And this plateau in here is What defines the strength class, as we've discussed in previous slides, also known as FCK, or characteristic strength of concrete. We will discuss the other parts of the graph a little bit later. What this smaller graph represents, so the smaller solid line, is the design strength. So we cannot assume a full tested capacity in our design, because there's a lot of uncertainty between testing and reality.
So we use a more pragmatic value, we reduce the strength of our concrete to a design value, known as FCD in a lot of design codes. And sometimes designers also simplify the behavior of concrete, so they don't assume this non-linear behavior. They assume linear, and then the strength is reached, or they just assume that the concrete does nothing until the strength is reached. And you will understand this a little bit more in later parts of the course, when we do some examples. Now these graphs are only applicable for concrete in compression.
As you might already know, concrete is only really strong in compression, i.e. when it's being squashed, but not very good in tension, when it's being pulled. And therefore, we use steel reinforcement and pre-stressing in order to achieve that tensile capacity when it's needed. Tensile strength of concrete is only one-tenth of the compression capacity. So, for example, if you use a 50 MPa concrete for compression, you have a strength of 50 MPa characteristic. The tensile capacity is only 5 MPa, so what we tend to do is to provide steel reinforcement.
And steel reinforcement and pre-stressing also have their own strength classes. The strength of reinforcing steel tends to be between 400 and 600 MPa, whereas the pre-stressing steel is very, very high. It's between 1,400 and 1,800 MPa. This huge material strength means only a small amount of steel is needed to reinforce concrete in tension. However, good bond needs to be provided between concrete and steel, and this is why reinforcement bars often have the ribs, as shown in this picture. Let's look at how steel behaves in a tensile test.
So, when steel bar is being pulled apart, it exhibits a very linear behavior. Unlike concrete, which goes pretty much non-linear up to the point it reaches its strengths, the steel acts very linear until the point of yield, which defines the strength of a steel bar. After it reaches a point of yield, it starts extending a lot for a very small increase in force. What we tend to use in design is this yield strength, and the design curves will specify FYK as the strength of the bar, and that's the strength class of the bar.
Typically, a 500 MPa steel is used for reinforcement, so your FYK is typically about 500 MPa. Similarly to concrete material model, the steel material model has some simplifications. The most common material model for steel is elastic perfectly plastic model, which is defined in many codes. What we assume is that the stress in steel is proportional to deformation related to its young modulus up to a point of yield, and after the point of yield, the steel just starts giving. So, it locks the stress at the same level, and it will simply start deforming without any additional force.
That's a very simple model to apply in practice and in hand calculations. In some situations where the steel strength governs, and especially in pre-stress sections, what you can do is you can use some strain hardening, which gives the steel a little bit of extra strength up to the point of rupture. This is slightly more representative of the real world, where the steel will yield, and it starts necking, and then it starts hardening up to a point where it ruptures. But, in most cases, it doesn't really give you much more capacity for a lot more computational effort involved.
So, for most daily situations, use elastic, linear plastic. We have now looked at each material individually. But what happens if you combine the two materials together? You'd rarely use concrete on its own, and although steel sections are used on their own, this is not the subject of the course. What you'll find in most real-life situations, especially in bridges, is that you have reinforced a concrete situation. So, the two materials are actually acting in composite. So, what we'll do now is we'll discuss how the actual reinforced concrete section behaves as a composite.
And there are a few behaviors that we need to discuss. We need to discuss uncracked versus cracked properties, some modes of failure, or how the section will fail in real life, limit state design, and how do we reinforce the sections enough. Let's look at uncracked versus cracked sections. Imagine a simply supported beam made of concrete. Some reinforcement bars are provided at the bottom to protect it from bending. Notice how the steel reinforcement is not positioned at the bottom face, which would be optimal, but slightly inside the concrete, and that's to provide cover against corrosion, and in some cases against fire.
What you'll find is for smaller loads, when the concrete is uncracked, it will behave pretty much like any elastic material. With plain sections remaining plain, your strain will have a linear profile, increasing from the centroid, which is roughly in the middle, to the extremes, where your strain is maximum. And again, because it behaves elastically, your stress will be proportional to your strain. Notice how you'll get more stress in your reinforcing bars, because it's got a much stiffer behavior. It's got a much larger Young's modulus than concrete, so for the same amount of strain, you'll see a very different amount of stress in that bar.
But for small loads, we tend to ignore the steel reinforcement. This is only valid for very small loads, until the concrete tensile capacity is reached. As we've already discussed, concrete tensile capacity is very small compared to its compressive capacity. And in reality, if you want to use your section to the maximum capacity, you need to assume that the concrete has cracked. We are now relying on steel to resist the tensile stresses at the bottom of the section. But luckily, we know that steel is really good at that.
What you'll find if you look at the section, is that your strains will remain linear, but the centroid will shift. And that's because we have lost all of this concrete intention. Even though the section is deforming, you'll find because of the crack, there's no stress at all in concrete. It has completely lost the connection between grains. What will happen is that the steel will take all of that stress. It will start extending until it reaches a yield point. And at the top, the concrete will start plastifying and behaving non-linearly, forming this compressive stress block.
But don't worry about this diagram too much. We'll do some examples later that will explain it in a lot more detail. Thank you for listening so far.