← Previous lessonFree lesson 2 of 3 · lesson 2 of 7Next lesson →

Unlock all 7 lessons of Control Theory PMSMFull course ₹40,000 · paid

Price & syllabus
Free lesson · 22 min · no payment

Vector Control Loops, Clarke and Park Transforms, Current Limits

A free lesson from Skill-Lync's Control Theory PMSM course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Control Theory PMSM - Session 2”

What will you learn in this free Control Theory PMSM lesson?

The instructor draws the vector control block diagram: a speed PI controller sets Iq, Id is set to 0, and current PI controllers feed an inverse Park transform and SVPWM. The Clarke, Park and inverse Park equations are listed, SPMSM and IPMSM are compared, and the current circle and voltage ellipse limits are explained.

  • Speed and current PI loops in vector control
  • Clarke, Park and inverse Park transformations
  • Why Id equals 0 fits SPMSM, not IPMSM
  • Current circle and voltage ellipse limits

What comes after lesson 2?

The next free lesson is lesson 3, “MTPA, Field Weakening and MTPV Control of an IPMSM” (25 min). Later in Skill-Lync's Control Theory PMSM course (paid): lesson 4, Control Theory PMSM - Session 4; lesson 5, Control Theory PMSM - Session 5; lesson 6, Control Theory PMSM - Session 6. The full course has 7 lessons (2 h 15 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

So welcome back and welcome to the session 2 of week 1. In last session we have discussed about the generalized concept of VC and we have finished that with the concept that torque is proportional to IQ under VC. It has understood the phasor diagram or the vector diagram under VC. So here you can see this is DXS and this is DS is basically this is the phase A axis or the alpha axis and if we want to make ID equals to 0, under this condition ID equals to 0, the IQ will be equals to IS because this ID component is 0.

So IQ will be equals to IS and IQ will be definitely in the along the Q axis and this is the VS. VS will have a this is the power factor angle and here you can see ID equals to 0 and this is the lambda M which is along the D axis. So you can see this is the phasor diagram or vector diagram under the vector control scheme and under this scheme here you can see in this case your current vector vector and the flux vector is orthogonal to each other 90 degree with each other and your flux is basically given by the your permanent magnets rotor and this current is produces by the stator currents.

So here we have two separate vector one is the current vector one is the flux vector both are decoupled in nature means both will be controlled by different variables and also orthogonal in each other so this is similar situation like DC motor. So here you can see the control block diagram or implementation block diagram of vector control. So first just like for any other control thing the reference speed of the motor will be compared with the this is the reference speed this is the actual speed.

So actual speed will compare with the reference speed and the PI controller will process it and produces the torque reference or IQ current reference here current is proportional to torque. So it will be we can consider it directly as a current reference and ID as I said ID has to be set to 0. So this ID and IQ will go to the vector controller and from here we will have the our rotor position sensor which will sense the theta E and this lookup table will produces these sin theta E cos theta E this is called unit vector and this will this block that vector rotator block will do two work one is convert this ID Iq into I alpha I beta then again it will convert this I alpha I beta to Ia Ib Ic so this vector rotator block will do two conversation one is ID Iq to I alpha I beta and then I alpha I beta to Ia Ib Ic.

Then this Ia Ia Ib Ic reference will be given to the inverter and inverter will produces Ia Ib Ic current for the PMSR and motor will operate it in a vector control mode. So this picture here we have the block diagram which is more detail in nature and can easily understood that with this diagram we can have more insight of the vector control scheme. So let us think that what we have so first this is the motor where the speed is sensed by the sensor and this speed is compared with the reference speed.

Now the actual speed and reference speed is compared and the error is amplified through the speed controller which will give you the torque reference. Then with the gain this torque reference will be converted into the Iq current reference. This is a linear gain because we have already see that the torque and current is basically proportional. So your Iq current and another thing is there here you can see that Ia Ib Ic three phase current will be measured. Then this block will convert this Ia Ib Ic into I alpha I beta which is known as Clark's transformation.

Then this I alpha I beta will be transformed to Id and Iq which is known as Park's transformation. So this Id and Iq will be compared with the reference Iq and Id. As I said the reference Id will be set to 0 and reference Iq is generated by this speed control loop. So now these after comparing Id Iq and Iq star and Iq and Id star and Id. This error will be again processed through the current controllers which is also PI controller. The speed controller is a PI controller.

The current controller is also PI controller which will produce the two voltages. That is the quadrature Q and D axis voltages. So these DQ voltages now by doing the inverse spark transformation that from DQ to it is converted to the alpha beta reference frame voltage. Now this SVPWM block this is a PWM technique which is used to generate the gate pulse for the three phase inverter. According to the this V alpha and V beta input. Because this voltage has to be generated this V alpha and V beta voltage has to be generated by this three phase inverter.

And for this purpose we using this PWM technique for generating the gate pulse for the inverter. And accordingly when the gate pulse will be provided the inverter. The inverter will provided the three phase voltage VAM, VV, VC. Required three phase voltage to produce the required torque and speed. So this is the basic concept or basic control block diagram for vector control. So now here we need to in this scheme we have already see that there is a some transformation is required. Like Clark transformation where ABC frame voltage is transformed to alpha beta voltage.

So here you can see that how this thing will be done. The equations are given here. So alpha voltage will be directly current is equals to IA current. Because we have aligns the alpha axis with the phase A axis. And beta will be given by this equation. So by using this equation we can convert ABC current to alpha beta current. Similarly we need to convert the alpha beta current to DQ current. So here you can see the equations which is these things we have already discussed.

So again it is given as for ready reference that DQ current can be calculated by this equation from the alpha beta current. And this phasor diagram is showing the DQ reference frame and alpha beta reference frame. This theta is the angle between the D reference frame and the alpha reference frame. The equations what we have I have summarized the equation that I alpha equals to this I beta equals to this. So these are the equations to use the ABC to alpha beta to convert ABC current to alpha beta current.

And this is the equations which will be used to convert alpha beta current to DQ current. These are the important because we have already understood that these transformation is required to implement the vector control theory. And this is the reverse transformation because we need to do the reverse transformation also. So the inverse spark transformation that DQ voltage is given and how to get the alpha beta voltage. That is let me go back to that light. So you can understood that why these two transformation yes. This is the block where we need to convert DQ to alpha beta.

So this will be V alpha this will be V beta. So like here we need the ABC to alpha beta and alpha beta to DQ and where we need the DQ to alpha beta. So both the transformation is required for this is your Park transformation and this is your inverse Park transformation. And this is the Clark transformation. So these are the three transformation we require Clark transformation Park transformation and inverse Park transformation. So here the equations are summarized. This is the Clark transformation equation. This is the Park transformation equation.

and this is the inverse Park transformation equations. So let us, so this is all about the vector control theory. So let us analyze the generalized vector control theory for whatever we have learned that we need to be analyzed for SPMSM and IPMSM. That these are vector control theory which we have learned till now is basically applicable to SPMSM and IPMSM both but there will be certain issues for IPMSM that I will discuss now. So first start with the SPMSM. As I said the SPMSM is basically non-salient pole machine. So your for SPMSM the LD will be equals to LQ. So the torque equation of the SPMSM is become this 3 by 2 P by 2 lambda M into IQ. Keep in mind that in case of a vector control we need to make ID equals to 0 to reach this equation.

But here we don't need to, if the motor is SPMSM then we don't need to make the ID equals to 0 to reach this conclusion. This equation will automatically for SPMSM the torque equation automatically boil down to this thing because of that LD equals to LQ characteristics of the SPMSM. In this equation if we make ID equals to 0 so actually ID is not contributing to the torque production. So there is no need of ID in case of SPMSM torque because ID is not there in the equation. Now so the total current which is taken by the motor stator is basically given by IS is equals to root over of ID square plus IQ square. Now as we have already learned in the previous slide that in case of SM, ID don't have any contribution for torque production. So if we want to minimize the stator current then we need to make simply ID equals to 0 in this equation. So that will give you.

. The minimum current, maximum torque for minimum current. Okay. Because if I make ID equals to 0 here, so I will get the minimum value of IS for a particular value of IQ. So it is clear that for the above equation shows that the stator current will be minimum if for IQ, if ID equals to 0. So you can see that in our vector control concept, which we have discussed, we consider ID equals to 0. So if we apply that vector control for SPMSM, so that will also assure the maximum torque per ampere control of the SPMSM.

Because the torque is not depending on ID, so making ID equals to 0 is not going to change or not going to, not going to change the torque. But at the same time, it will minimize the stator current that is the IS. So we can assure maximum torque per ampere control under this control for SPMSM, if we apply the generalized vector control theory, which we have already discussed. Now let us consider for the IPMSM. Now this is the torque equation and for IPMSM, LD is not equals to LQ.

So here you can see the concept, the idea which we have used for vector control theory that ID equals to D. If we put ID equals to 0 here, then this part of the expression will become 0. That means the torque will be reduces if we put ID equals to 0. Because torque has two components. One is this component, one is that component. Now generally for IPMSM, IQ greater than ID. So if you put some amount of minus ID here, so that will contribute to your torque production.

So making ID equals to 0 is not a good control idea or control technique for IPMSM. Because making ID equals to 0, that will minimize the current, but that will not maximize the torque. So we cannot achieve the maximum torque per ampere control of IPMSM machine by the vector control theory, which we have discussed. Make it clear that here, because here this torque component, this ID is already in the torque equation. So if we make ID equals to 0, so the torque will not be going to, torque will be affected and it will be reduces.

So to solve this problem, we need to think about some other solutions. That I will discuss later on that how to operate a IPMSM machine under vector control and at the same time, it will also operate in maximum torque per ampere control. So here you can see the torque is basically related to ID and IQ. So we have to think about something else to sort out this problem. So as I said that some amount of negative ID current will, the reluctance torque will be contribute the total torque production.

So for IPMSM, total torque cannot be maximized for vector control by considering the ID equals to 0. This thing I have already discussed. So as a result, IPMSM vector control by considering ID 0 won't be able to provide the maximum torque per ampere control like SPMSM. So I will discuss MTPA later on. So let us discuss some other issues related to vector control first. Like here we will discuss the current and voltage limit. So first we need to understood that every machine, every motor or every electrical equipment have a limit on its how much current or how much voltage we can apply to the machine that has a limit.

So here in case of a PMSM motor that will also have the voltage and current limit. So how to calculate the voltage and current limit. So and while designing the machine control or while setting the value of IQ and ID or the while setting the values of the PI controllers, we need to assure that the motor current and voltage should not exceed the maximum permissible limit. So you know the stator current is basically the summation of ID square and QS square root over of this. So this equation will determine the stator current limit.

So your ID and IQ should not be such that so that the IS should not exceed the maximum permissible limit. Where ISM, let it is the maximum permissible limit. So your ID root over of ID square into IQ square should be less than equals to ISM. So if we plot this ID and IQ limit in DQ coordinate, so we will have a circle. This is the circle that means for different we can observe the same current limit with a different value of ID and IQ. Like here the ID equals to 0, IQ equals to 0 and the whole limit is observed by ID and here the ID equals to 0 and whole limit is observed by the IQ.

In between here we have the ID and IQ both. So you can see for different value of an ID and IQ we can have same amount of IS is the stator current. That limits are plotted here. This circle is known as current circle. Okay, actually ID minus ID is basically demagnetizing produces demagnetizing effect. So we cannot as per the manufacturer data seed we cannot produces we cannot use ID. We have a certain limit on the application of ID. So this brown side is this shaded portion is actually showing the limiting area of the ID that maximum what should be the maximum negative value of the ID is possible.

So here you can see that is this area we cannot operate the motor in this area. We have to operate the motor in the shaded area and the right side area. Right side there is no issue of using the no issue of operating the motor in the first quadrant because first quadrant will produces positive ID which is not required. So either we have to operate from here to here within this zone this shaded zone. This is the shaded zone in which we need to operate the our motor that IQ will be positive for motoring.

IQ will be negative for regeneration and ID will be negative for maximum torque per ampere control or field beginning control. So this shaded part of the figure is actually showing the zone within which we can operate our motor. So here you can see that how to implement the current limit. Actually we need to after we need to connect some limiter after the PI controller. So how this thing will be happen that is current PI controller. After current PI controller we need to connect this limiter. So how it will happen.

So here you can see that is the limit ISL. This is the ID value. So first ID value will be coming. So from ID value it will observe the limit. Then from this ID value and from ISL limit it will IQ limit will be calculated and IQ limit will be positive and negative. This is the IQ limit. So your IQ should be within this limit. It should not increases. Here you can see the IQ will increases positive direction and it can reach up to maximum this.

And similarly it can increase in the negative direction and up to maximum this. So if any value of IQ more than this limit is entered into the box so the output will be only the limiting value. It will not be the actual value of the IQ. It will be limited by this limiter. Similarly here you can see there is no use of positive ID current. So here we have a limiting in the negative ID current. So this is the maximum value of the negative ID current will be possible.

Because if the value of the ID is below the limit then this box will directly pass the ID. And if this value is more than the limiting value then box will make it limited. So next we will observe the voltage limit. So similar to current limit we will have the voltage limit. So voltage, the stator voltage will also be calculated as just similar to the stator current. And it should be also below the voltage limit where VESL is the maximum voltage amplitude of the stator voltage which can be allowed.

And our VD and VQ should be always under this limit. Now actually we have observed the current limit circle in the ID-IU plane. So it will be easier to express the voltage limit circle in the ID-IU plane. So this is the relationship between the voltage and the current at steady state where the omega R is the rotor speed. LD I have already told, lambda M, IQ these things I have already discussed. So this is the relationship between the voltage and the direct access voltage and the current.

And this is the relationship with the quadrature access voltage and the current. That is the ID-IQ current and this is the direct relationship. So if we substitute these values, these values in this equation, then we will get the voltage limit in terms of current. So from where we can find out from that limit, we can find out the value of ID in terms of voltage limit and IQ. So this equation will give you the value of ID for which we can observe the voltage limit. Okay.

Because VSL is there in this equation. So from here, if VSL, this voltage limit is known, then we can calculate the ID by using this equation so that the current will be limited. So if we plot this equation in ID-IQ reference frame or ID-IQ graph, then we will have the, this will be elliptical in nature. So this equation, the locus of this equation will be elliptical in nature. So these are the ellipse which is known as voltage ellipse. So here you can see, this is the current.

And this solid line is the current circle that means which will observe the current and this is the voltage ellipse. So here you can see that as the speed increases the voltage ellipse shrink and this shaded portion as I have already told you that this is the part where we need to operate the machine. So stator current vector must be remain inside the ellipse. It should be assured that the stator current must be inside the current circle as well as inside the voltage limit. So in low speed the voltage limit is quite large so it will be obviously inside the current voltage limit both but as you can see as the speed increases because in this equation here you can see this equation we have speed.

So as the speed increases the circle will shrink the ellipse will shrink. So in higher speed we need to take care of these things that the current should be within the current limit as well as within the voltage limit. Both the limit has to be observed. The control system the voltage limit can be observed in practice by incorporating the ellipse into the control system. Similarly the current circle can be observed in the control system. Similarly the current circle can be observed in the practical by incorporating the equation related to the current limit.

So in next session we will discuss about the maximum torque per ampere control.

Want the rest of Control Theory PMSM?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Control Theory PMSM course

The remaining 4 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Control Theory PMSM course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.