Lesson finished
Up next: Vector Control Loops, Clarke and Park Transforms, Current Limits
Unlock all 7 lessons of Control Theory PMSMFull course ₹40,000 · paid
PMSM Basics and the Idea Behind Vector Control
A free lesson from Skill-Lync's Control Theory PMSM course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Control Theory PMSM - Session 1”
What will you learn in this free Control Theory PMSM lesson?
The instructor compares surface and interior permanent magnet motors and lists their advantages, including a 5 HP example at 8 kg against 40 kg for an induction motor. The lesson explains why volt by hertz control fails for a PMSM, reviews dq reference frame modelling and shows that setting Id to 0 makes torque proportional to Iq, as in a DC motor.
- Surface versus interior PM synchronous motors
- Constant torque and constant power zones
- Why volt by hertz control fails for PMSM
- Torque proportional to Iq when Id is zero
What comes after lesson 1?
The next free lesson is lesson 2, “Vector Control Loops, Clarke and Park Transforms, Current Limits” (22 min). Later in Skill-Lync's Control Theory PMSM course (paid): lesson 4, Control Theory PMSM - Session 4; lesson 5, Control Theory PMSM - Session 5; lesson 6, Control Theory PMSM - Session 6. The full course has 7 lessons (2 h 15 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Good morning everybody. Welcome to the course of P-M synchronous motor control theory. So in this course we are going to cover introduction to PMSM, overview of PMSM control, basic theory of vector control of PMSM, rotor reference frame, modeling of PMSM, generalized vector control of PMSM, analysis of generalized vector control for SPSM and IPSM. Current and voltage limit, maximum torque per ampere control and field weakening control of PMSM. Maximum torque per voltage control, transient among the MTPA and MTVV technique, comparison of MTPA control and MTVV control, direct torque control of PMSM, comparison of vector control and DTC, simulation study of vector control drive.
So these are the things we are going to learn. So what are the things we are going to learn is that identification of the advantages of the PMSM, selection of control strategy for PMSM for an application, the DQ reference frame model of PMSM, developing the vector control scheme of PMSM, PMSM, analysis of stator current and voltage limit, analysis of stator current and voltage limit, developing the MTPA and MTPV control strategy for PMSM, developing the DTC strategy of PMSM, executing the simulation study of vector control PMSM drive.
So let us start the session 1 of week 1. So first we need to introduce with the PMSM. So PMSM basically having a stator winding similar to the conventional synchronous motor that is the three phase distributed winding. But its rotor winding is basically consists of permanent magnet instead of field winding. And when the stator is supplied with a three phase balance AC, it will create a rotating magnetic field just like conventional synchronous motor. So the main difference is that each field flux is created in case of a PMSM field flux is created by permanent magnet instead of the field winding.
So there is a two type of PMSM based on the construction. One is the surface PM synchronous motor. Here you can see this is the surface PM synchronous motor where the permanent magnet is attached with the surface of the rotor. So here you can see a four pole rotor and the permanent magnets are attached with the surface of the rotor. And another type is the interior PM synchronous motor where the permanent magnets are inserted into the rotor. So here you can see in the right side figure. So these are the permanent magnets which is inserted into the rotor.
In this figure you can also see the axis. This is the phase A axis. This is phase B axis and this is phase C axis. And also this is the D axis that is a direct axis which is basically aligned with the rotor D axis. And this is the quadrature axis which is placed 90 degree from the D axis. Electrical 90 degree from the D axis. Similar axis you can also see in this graph or in this figure. So let us understood what are the advantages of PM synchronous motor over normal AC motor like induction or synchronous motor. So here you can see these are the advantages. First thing is the high efficiency. PM synchronous motor has higher efficiency compared to the induction or synchronous motor. It has a higher power to weight ratio. It has a compact size. It has a robust construction and low rotor inertia and superior control characteristics.
So in the right side figure. So in the right side figure you can see a comparison of PM motor with the PM synchronous motor with induction motor. So if you compare a PM synchronous motor of 5 HP with the induction motor of 5 HP then you can see the weight of PM motor will be 8 kg where the similar power motor that is the weight of induction motor will be 40 kg. So this is definitely PM motor has a higher power to weight ratio compared to the induction motor. Similarly if we compare the induction motor. Similarly if we compare the induction motor with the PM synchronous motor then its volume will also be 70% smaller for the same HP rating. So here you can see this is the PM synchronous motor volume and the shaded one is the induction motor volume. So it is clearly understood from this figure that what is the advantages of PM synchronous motor over the induction motor.
Next is the field of applications. So where we can find the application of PM synchronous motor are servo and robotic drives that for servo and robotic applications. The motor which used for servo and robotic applications are PM motors. Electric vehicle. Electric vehicle is the most widely used sector where the PM motor is most widely used in electric vehicle. Almost every electric vehicle runs in PM synchronous motor. Similarly aerospace application. Similarly aerospace rovers are basically operated with PM synchronous motor and solar power drive. Next is the overview of the PM synchronous motor control. So in the left side you can see a generic diagram block diagram of any kind of electric motor drive. So this generic block diagram is also applicable for PM motor.
So what we have in this diagram. So what we have in this diagram. Then the right side we have the supply. Then we have the inverter. Then we have the motor. So power will flow from the supply to the inverter to the motor. And we also have a control system which will control the inverter based on the feedback coming from the motor. So what are the feedback which can be coming from the motor. It may be position of the rotor. It may be speed of the rotor.
It may be the torque of the rotor motor or sometime we need the current and voltage feedback for controlling the motor. So this control system will take the feedback and based on that feedback there will be a control algorithm inside the control system. So that control algorithm will control the inverter and then the inverter will vary the voltage and frequency according to the control logic and the motor will operate. And a supply also required for to operate the control system. So this will be the power supply. This thing will denote the power supply for the control system.
Now any drive system has to be operated in a different zones. So here you can see in this figure we are actually discussed about the power and torque versus speed curve of a EV drive that is electric vehicle drive that this is basically applicable for electric vehicle and some other applications also. So here you can see that we have taken power and torque in the y-axis and speed in the x-axis. So red one is representing the torque and the blue one is representing the power. So here you can see from zero to base speed the torque is constant and the speed is increasing so the power is increasing.
So this zone is known as constant torque zone. After the base speed up to the maximum permissible speed of the motor you can see the power is constant. And as the speed is increasing so torque is decreases. So that's why this zone is known as constant power zone. So if we relate with the electric vehicle from zero to base speed that is when the at the time of acceleration the motor will operate in the constant torque zone. And when it is reaches the base speed after that if you want to increase the speed of the vehicle then we need to operate in the field wing region.
So what are the different control techniques available for PMSM control? So significant control techniques are vector or field oriented control, maximum torque per ampere control, maximum torque per voltage control and direct torque control. Maximum torque per ampere control and maximum torque per voltage control is actually the extension of the vector control theory. So this is basically some addition with the vector control theory. Now very obvious question will be rise in your mind that why can't we use volt by hertz control in case of a PM synchronous motor?
Because all of you know that for induction motor volt by hertz control is a very popular kind of control technique. So these are the reasons that why we can't use the volt by hertz control for PMSM. The first reason is the starting jerk or temporary reverse moment at the time of starting. So it is a big problem. And also the loss of synchronism during the acceleration and sudden road change. Third problem is the slow dynamic response. So these things can be understood from this right side figure.
You can see these figures is drawn from the machine torque motor speed versus time curve. So here you can see the last curve which is the slowest curve. The if the motor will follow this curve, then it will take 20 seconds to accelerate. That means yes, it will operate and it will accelerate, but it will take very high time. That means it if you want to operate by volt by hertz control, then the dynamic response will be slow. Now if you want to make the dynamic response fast, then you can see here in the last curve that which is try to accelerate the motor up to 600 RPM speed with a time of 5 seconds.
After that it will lost its synchronism and with some oscillation it will reach to zero speed. So it cannot be accelerated fast by using volt by hertz control. So that's why the volt by hertz control cannot be used for PMSM synchronous motor control. So next is the basic theory of vector control of PMSM. So before understanding. So before understanding. The basic theory of vector control of PMSM, we have to understood that what is the generalized concept of torque production in any kind of electric motor. So basically the electromagnetic torque which is produced in any kind of electric motor is basically the interaction of the stator and the rotor magnetic field.
In mathematically, that means a field will be created by the stator winding and a field will be created by the rotor winding or the rotor magnets. An interaction between the stator field and rotor field, the flux torque will be created. And this is the generalized concept. Every machine, whether it is a DC machine, whether it is a induction machine or whether it is a PM synchronous machine, for every machine, this concept is applicable. So in mathematical sense, torque is given as a cross product of rotor flux linkage and rotor current.
So mathematically, it is shown here that this KT is a constant and your lambda M is basically the rotor flux linkage and IA is the your armature current or the rotor current. Go to the next slide. So let us try to understood the DC motor torque production theory because this concept, the DC motor torque production theory concept is actually required to understood the vector control concept. So here you can see that basically in DC motor, this is a cross sectional view of a DC motor. So in DC motor, this is the armature.
So here armature is the rotating part and this is the field winding. So field winding will produce a flux which is shown by this green line. So this is the field flux which is produced by the field winding which is fixed because your field magnets are static. And also this armature conductor will produce a field which will be shown by this red line. So you can see due to the presence of the commutator, the armature current, the flux produces by the armature current and the flux produces by the field winding or field magnet is always orthogonal to each other.
That means the angle between these two is always 90 degree. Also the amplitude of these two flux vector is actually controlled by the two different current. Like this field flux vector is controlled by the field current and the armature flux vector is controlled by the armature current. So this is a wonderful feature of a DC motor which makes the DC motor equation very simple. You can see is if lambda M and Ia, here we have a cross product of lambda M and Ia. Now if the angle is always 90 degree, the equation will simply boil down to KT lambda M into Ia.
So in case of a DC machine, we can see that if the field flux is kept constant, then the torque is directly proportional to the armature current. These features make DC motor torque control straightforward and provide superior dynamic performance compared to the scalar control AC motor. Scalar control AC motor means like volt by hertz control induction motor. So a DC machine torque control characteristics is always better than a induction machine volt by hertz control drive. So this is the thing where the engineers start thinking about it that can we make the AC machine control like DC machine control?
So let us try to understood what are the AC machine control concept? Note that in case of an AC machine, the torque is produced by field flux and here is the, if we consider the induction motor. Then in that case, the field flux and the armature current, both are produced by the three-phase AC current. So the flux, the air gap flux and the armature current, both are actually produced from the AC mains. So we don't have a decouple control between the field flux and armature current.
So that is the problem with the AC machine that is not like DC machine. Like in DC machine, we have a separate current which control the field flux and we have a separate current which control the armature flux and these two flux is orthogonal to each other. So in AC machine, neither is there, neither we can, both the field flux, that is the air gap flux and the armature current, both are controlled from the stator current and these are not orthogonal in nature. So that is the problem with the AC machine.
So the main objective of vector control is to make two magnetic field decoupled and orthogonal as much as possible. That means in case of AC machine, if we can make the stator flux and the rotor flux orthogonal to each other and if we can control these two flux separately by two separate current, then the induction machine or the PM synchronous machine or any kind of AC machine can be controlled like DC machine. So this is the main essence of vector control for application of vector control for AC machine control.
So VC is used to control the PMSM when superior dynamic performance is required. We can control the PMSM by some other method like self-control method, but VC will give the most superior type of dynamic performance. For realizing the VC, PMSM model in rotor reference frame is necessary. That means we have to convert the PMSM mathematical equation into DQ reference frame. So generally the equations are given in three-phase static reference frame. So you have to convert this equation to three-phase rotating reference frame, which is the DQ reference frame.
And then only we can implement the VC or the VC theory can be implemented. VC means the vector control theory can be applicable to AC machines. So let us have a quick review of rotor reference frame modeling of the PMSM. So you can see this is the schematic of the cross-sectional view of the PMSM, which is a two-pole PMSM. Now here we have shown all three axes like the A, B, C. These are the winding of the A phase, B phase, and C phase. And this is the alpha axis, which is actually attached with the A phase magnetic axis.
And this is the beta, which is 90 degree with the A phase magnetic axis. And this is the D axis, which is in phase with the, or attached with the north pole of the rotor. So these D axis will rotate with the rotor. And this is the Q axis, which is 90 degree from the D axis. So DQ is basically rotating axis, where alpha, beta, ABC and alpha, beta are the static axis. Where ABC is the three-phase static axis, alpha, beta is the two-phase static axis, and DQ is the rotating, rotating two-phase axis.
And theta is the angle between the alpha axis and the D axis. So now let us have a quick review of reference frame transformation. So any sinusoidal variable, three-phase sinusoidal variable, if we find out the, it's vector summation of three-phase sinusoidal variable, where the coils are one-tonary phase apart. So we will have a rotating vector. So here you have shown three current, the I, U, I, V, and I, W, that is I, I, I, B, and I, C. So three current, if we find out the resultant of these three current, then we will have a vector V, F, which is known as a current vector, which will rotate in space.
So here you can see the current vector, F, which is basically a constant amplitude, but rotating in a speed of omega, where omega is the basically the frequency of the currents. So this, if we consider two axes, alpha and beta, which is static axis and two-phase, then we will have the two component on this F, that is the current space vector. We will have two components, one along the alpha axis and one along the beta axis. So this is the equation by which we can convert ABC to the alpha-beta component.
Similarly, if we consider the rotating axes, that is D and Q, so this alpha-beta component can also be transferred to the DQ component. That is, this F vector will have components on D, rotating D and rotating Q axis. So this is the equation where you can see that how this DQ component will be converted from the alpha-beta. So here you can see that for conversion of alpha-beta to D, DQ, we need to know the angle between the, your alpha axis and the D axis. Now DQ as it is a rotating axis, so your theta will be always, it will be changing.
So you can see that the theta will be changing. So we need to know the theta at every time if we want to convert that alpha-beta into the DQ axis. And if your, the speed of the DQ axis and the speed of the rotating current vector are same, then this ID and IQ will be constant value. So it will become DC value. Now we are ready to develop the DQ reference frame model of the PMSM. So this is the basically three-phase stator reference frame model. So VA is the stator A phase voltage.
RS is the stator per phase resistance. IA is the stator current. And lambda A is the stator flux linkage. So this is the equation for phase A and this is the equation for phase B and phase C. So dynamic model, so if we convert this equation, By using the transformation equation which we have discussed in the previous slide, then we will get the DQ reference frame model of the machine. So this is the DQ reference frame model of the machine. So here you can see that VD is the direct access voltage and LambdaD is the direct access flux linkage and LambdaQ is the quadrature access flux linkage.
So this is and VQ is the quadrature access flux voltage. So here you can see this equation is for D-axis and this equation is for Q-axis. Similarly, we can derive the torque equation in the DQ reference frame. So if we derive the torque equation in DQ reference frame, then the torque equation will be something like this. So observe this torque equation carefully that what we have in this torque equation. 3 by 2 is a constant, P is the number of pole and LambdaM is the rotor flux linkage.
IQ is the quadrature access current. LD is the direct access inductance. LQ is the quadrature access inductance. ID and IQ are the direct access current and quadrature access current. So you can see in this equation, now the torque is become as a function of two current and one magnetic flux. So now the torque equation is become much similar to the DC machine torque equation. It will, it will be more clear that under VC how the torque equation will be similar to the DC machine. Now let us discuss the vector control theory.
So to understood the vector control theory, first we need to understand the PMSM phasor diagram or rather say it is not phasor diagram. I should rather say it is a space vector diagram or because all the quantities here shown are basically the space vectors. So you can show this is a D-axis and this is the Q-axis. So the rotor flux linkage that is a LambdaM which is along the D-axis and LambdaS is the stator flux linkage. Stator flux linkage has two components. One is along the D-axis that is the LambdaD and one is along the Q-axis which is the LambdaQ.
Now we have the IS is the stator current space vector. So this current space vector has two components. One is along the D-axis ID and one is along the Q-axis IQ. And this is the VS which is the voltage space vector of the stator. So this voltage space vector will create the current that will lag between the voltage and current due to the, here we have considered the lagging power factor that is the operation of the motor. And delta is the phase angle between the rotor flux and the stator flux.
This is known as torque angle. And beta is the angle from the, of the current from the D-axis. Let us try to understand the vector control theory. So torque equation I have already discussed that this is the torque equation. So here you can see in this torque equation, there is a two component of the torque equation. One is the LambdaM into IQ. So this component is basically depending on the two things. One is the rotor flux linkage. Another is the quadrature axis current of the stator.
And another component which is actually summation of ID and IQ that is direct axis current and quadrature axis current. And difference between the direct axis inductance and quadrature axis inductance. So there is a two component. First component is known as, this will produce the electromagnetic torque because this is the interaction between the field, between the flux and the current. And second one was the reductance torque. So reductance torque is applicable for, only for interior permanent magnet machine or salient pole machine. So now let us consider the vector control theory.
Say that we have set that ID equals to 0. That means we have given the ID, stator current ID of the motor we have considered as equals to 0. So what will be the torque equation? The torque equation will be become something like this. Because if ID equals to 0, then the salient torque component will be 0. So we only left with the electromagnetic torque component. So now you can see that, this equation is almost similar to the DC motor equation. Because 3 by 2 and P by 2 are the constant term.
The M is basically the rotor flux and IQ is the stator current. Just like DC motor where we have the field flux and the armature current. So this equation now become a similar equation by DC motor. So under vector control, we will, so what is the conclusion of this thing? That if we use vector control theory, that is basically if we express the machine's equations in DQ reference frame, then the torque equations will become, and we put ID equals to 0, then the torque equation will become similar to the DC machine.
That is if lambda M is constant. Here the lambda M is constant because the lambda M is produced by the rotor permanent magnet. So those are constant for a particular machine. And IQ is the stator current. So you can see that torque is become directly proportional to the stator Q axis current, which is similar to the DC motor. So, so finally we can conclude that under, if we express the motor equation in DQ reference frame, and if we apply the vector control theory by making ID equals to 0, then the torque of the PM synchronous motor will become proportional to the IQ current only.
So that's all for this session. So for the next session, we will start with the, how to implement vector control logic in a drive.