Illustration of a power converter board: power transistors on a finned heat sink, a copper toroidal inductor, electrolytic and film capacitors, copper bus bars and cable terminals
Courses / Power Electronics

Power electronics courses online

Every Skill-Lync power electronics course, from DC-DC converters and rectifier harmonics to converter design for EVs, with fees, hours, projects and which one fits your stage.

6
courses and programs
₹40,000
per short course
6 to 12
weeks per short course
1
program, ₹2,75,000

As of 20 Nov 2026 · Fees are the list price on each course page, inclusive of all charges

Skill-Lync teaches power electronics in 6 online courses: five 6 to 12-week courses on DC-DC converters, converter simulation for EVs, industrial converter hardware, rectifiers and harmonics, and a short converter-to-PCB overview, plus a 48-week PG program in power converter design that bundles four of them. Here they all are with fees, duration and projects, which ones overlap, and which fits the job you want.

Every Skill-Lync course that teaches Power Electronics

CourseLevelDurationProjectsFee
Design of Power Converter with PCB OverviewShort course6 weeks3₹40,000
Design Concepts of Power Electronic Converters for IndustriesShort course12 weeks2₹40,000
Simulation and Design of Power Converters for EV using MATLAB and SimulinkShort course12 weeks3₹40,000
AC-DC Rectifiers, Harmonics and Related StandardsShort course12 weeks2₹40,000
Fundamentals of DC-DC ConvertersShort course12 weeks2₹40,000
Post Graduate Program in Power Converter Design and AnalysisPG program48 weeks12₹2,75,000 · EMI from ₹14,375/mo

Projects is the number of industry projects listed on the course page. Programs also include the courses' smaller assignments. EMI figures are the lowest monthly plan shown on the course page.

Which one should you pick?

  1. You want the basics of switching converters, cheaply in time. Fundamentals of DC-DC Converters (12 weeks, ₹40,000) works through buck, boost, buck-boost, Cuk, SEPIC, ZETA and Luo converters, then Bode plots and state-space models. It has only 7 hours of video, the least of the five, so it suits engineers who want the equations and a structured set of exercises (a SEPIC converter and an MPPT controller) more than long lectures.
  2. You want converter design and simulation for EVs, renewables and data centres. Simulation and Design of Power Converters for EV using MATLAB and Simulink (12 weeks, ₹40,000, 22 h, 3 projects) covers the widest ground: boost and up/down converters, gate drivers, discontinuous mode, small-signal modelling, feedback control, isolated converters, rectifiers and inverters. Its projects are a converter design report, an interleaved DC-DC system for a data centre at 85% efficiency, and an H-bridge inverter for a microgrid. If you take only one course, this is the broadest.
  3. You want the hardware side: devices, magnetics, losses and cooling. Design Concepts of Power Electronic Converters for Industries (12 weeks, ₹40,000, 25 h) is about what sits on the board: switching devices, SiC and GaN, PWM methods, magnetics, inverter topologies, drives, cooling and snubbers. Projects: a DC-DC converter loss calculation and a three-phase EV inverter model.
  4. You work with grid-connected equipment, drives or power quality. AC-DC Rectifiers, Harmonics and Related Standards (12 weeks, ₹40,000, 23 h) is the only course on thyristor rectifiers, power factor correction, harmonic compensation and IEEE/IEC harmonic standards, with LTspice and MATLAB. Pick it for UPS, drives, HVDC and utility work, or as a second course after a DC-DC one.
  5. You want a short overview that ends with a PCB. Design of Power Converter with PCB Overview (6 weeks, ₹40,000, 23 h) packs switched-mode basics, buck and boost design, rectifiers and inverters, power components and automotive standards into five weeks and spends week 6 on Altium. Its converter weeks repeat material from the DC-DC and EV courses, so take it instead of them, not as well as them.
  6. You want a program. The Post Graduate Program in Power Converter Design and Analysis (48 weeks, ₹2,75,000, EMI from ₹14,375 a month, 99 h, 12 projects) contains four of the courses above (DC-DC fundamentals, the EV simulation course, industrial converters, rectifiers) plus Introduction to Physical Modeling using Simscape and the full Advanced PCB Design Using Altium course. It does not include the PCB Overview course. Buying the four short courses separately costs ₹1,60,000; the program adds Simscape, the full PCB course and placement support.

What is Power Electronics?

Power electronics is the part of electrical engineering that converts electric power from one form to another using semiconductor switches: a phone charger turning 230 V AC into 5 V DC, a solar inverter turning panel DC into grid AC, an electric car's inverter turning battery DC into the three-phase AC that spins the motor. The switches (MOSFETs, IGBTs, and now SiC and GaN devices) turn on and off tens of thousands of times a second, and inductors, capacitors and transformers smooth the result.

Converters come in four families: DC-DC (buck, boost, buck-boost, Cuk, isolated flyback and full-bridge), AC-DC rectifiers (diode, thyristor and PWM rectifiers with power factor correction), DC-AC inverters, and AC-AC converters. Design work is choosing the topology, sizing the inductor and capacitor, picking a switch, working out its losses and the heat sink, closing the control loop so the output holds steady, and meeting harmonic and EMC standards. The courses below split that work in different ways.

Here is the first calculation every converter course teaches. A buck converter steps 48 V down to 12 V at 5 A, switching at 100 kHz. Ideally the duty cycle is D = Vout ÷ Vin = 0.25: the switch is on a quarter of each 10 µs period. Allow a ripple of 30% of the load current, ΔI = 1.5 A, and the inductor is L = (Vin − Vout) × D ÷ (fs × ΔI) = 36 × 0.25 ÷ (100,000 × 1.5) = 60 µH. For 1% output ripple (0.12 V) the capacitor is C = ΔI ÷ (8 × fs × ΔV) = 15.625 µF.

Two things follow from those numbers. The inductor must carry a peak of 5.75 A without saturating, not just the 5 A average. And below 0.75 A of load (ΔI ÷ 2, 15% of full load) the inductor current touches zero each cycle and the converter drops into discontinuous mode, where D is no longer simply Vout ÷ Vin. Raise the switching frequency to 500 kHz and the inductor shrinks five-fold to 12 µH, which is why designers push frequency up. Check your own numbers with the buck and boost converter calculator.

The catch is loss. Take a MOSFET with an on-resistance of 10 mΩ that needs 20 ns to turn on and 20 ns to turn off (assumed, typical of a 100 V part). Conduction loss is Io² × D × Rds(on) = 0.063 W. Switching loss is ½ × Vin × Io × (tr + tf) × fs = 0.48 W at 100 kHz, so the switch dissipates about 0.54 W, 0.9% of the 60 W output. At 500 kHz the switching loss alone is 2.4 W and the total 2.46 W, 4.1% of the output. A gallium nitride (GaN) switch with 5 ns edges brings it back to 0.6 W of switching loss (0.66 W in all). That trade, smaller magnetics against hotter switches, is the centre of modern converter design and the reason wide-bandgap devices get a week of their own.

What a Power Electronics course covers

  1. DC-DC converters. Buck, boost, buck-boost and Cuk converters in continuous and discontinuous conduction; interleaved, SEPIC, ZETA and Luo converters; isolated DC-DC converters; ripple current and voltage, inductor and capacitor sizing; gate driver design for a boost converter.
  2. Rectifiers, harmonics and standards. Diode half- and full-wave rectifiers with R, RL, RLE and RC loads, three-phase bridges, thyristor phase-controlled rectifiers and inverter-mode operation, power factor and PFC rectifiers, PWM rectifiers, passive and active harmonic compensation (TCR, TSC, STATCOM), and IEEE 519 and IEC 61000-4-7.
  3. Inverters and drives. Single- and three-phase inverters, multi-level and neutral-point-clamped topologies, sinusoidal and space-vector PWM, an introduction to electric drives and AC machines, and a three-phase inverter model for an EV.
  4. Devices, magnetics and thermal. MOSFETs, IGBTs, SCRs and thyristors and how to choose one, SiC and GaN wide-bandgap devices, inductor and transformer design (a push-pull transformer), conduction and switching losses from an IGBT datasheet, heat sink and cooling design, snubbers and DC-link capacitors.
  5. Modelling and control. Transfer functions and Bode plots, averaged state-space models, small-signal models, controllability and observability, gain and phase margin, and closed-loop (feedback) control of DC-DC converters in MATLAB and Simulink; LTspice for rectifier circuits.
  6. Hardware design and PCB. Power components from switch to EMI filter, bus bars, clearance and creepage, UL 1741, UL 840, ISO 26262 and ISO 16750, EMC requirements, and PCB design in Altium Designer (a short introduction in one course, the full 12-week Advanced PCB course in the PG program).

The courses in detail

Design of Power Converter with PCB Overview

Short course6 weeks23 h of video₹40,000

A 6-week overview: switched-mode power converters, DC-DC converter and rectifier/inverter design in Simulink, power components, hardware design and an introduction to PCB layout in Altium. Projects: an LDO regulator PCB, a full-bridge converter and a converter loss calculation.

Projects include: Design of PCB Using Altium ECAD Software for a Low Dropout Voltage Regulator; Design and Simulation of Full Bridge Converter in Simulink; Loss Calculation for a DC/DC Converter Using MATLAB.

Tools: MATLAB, Simulink, Altium Designer

Design Concepts of Power Electronic Converters for Industries

Short course12 weeks25 h of video₹40,000

Hardware side of power electronics: converter components and standards, switching devices and wide band gap (SiC, GaN) devices, switching methods, closed-loop buck control, magnetics, topologies, single-phase inverters, drives, cooling, snubbers and DC-link capacitors.

Projects include: Loss Calculation of a DC/DC Converter using MATLAB; Modeling of 3 Phase Inverter for Electric Vehicle Application.

Tools: MATLAB

Fundamentals of DC-DC Converters

Short course12 weeks7 h of video₹40,000

Non-isolated DC-DC converters in MATLAB and Simulink: buck, boost, buck-boost, Cuk and interleaved converters (modes, ripple, continuous conduction), then design and modelling of each and Bode plots. 7 h of video; projects are a SEPIC converter and an MPPT controller.

Projects include: Design of DC-DC SEPIC Converter; Design of MPPT Controller.

Tools: MATLAB, Simulink

Post Graduate Program in Power Converter Design and Analysis

PG program48 weeks99 h of video₹2,75,000

Six courses in 48 weeks: Simscape physical modelling, power converters for EVs in Simulink, industrial converter design concepts, Advanced PCB Design using Altium, AC-DC rectifiers and harmonics standards, and DC-DC converter fundamentals.

Projects include: Preparation of Converter Design report; Design an interleaving DC/DC converter system for a data center application; Design and development of DC/AC H-bridge inverters for microgrid applications; Create a Project Workspace for MIC33030.

Tools: Simulink, MATLAB, Altium Designer, LTspice

Jobs after a Power Electronics course

Typical job titles: power electronics engineer, power electronics design engineer, hardware design engineer (power), SMPS or power supply design engineer, inverter or motor-controller hardware engineer, magnetics design engineer, and power electronics test or validation engineer. They work at EV and two-wheeler makers and their suppliers (traction inverters, on-board chargers, DC-DC converters), solar inverter and UPS companies, data-centre and telecom power-supply makers, industrial drive makers, and engineering services firms.

From Skill-Lync's own placement records (as of 20 Nov 2026, 3,905 placements): 5 have a power electronics or hardware design job title, at 4 companies, placed 2022 to 2025, with reported salaries from 2.8 to 4 LPA. That is too few records to quote a median. All 5 came from the PG Program in Electric Vehicle Design & Development, which has 546 placement records in all (median 3.5 LPA, n = 528 with a salary), most of them in other EV roles.

We have no placement record yet from the PG Program in Power Converter Design and Analysis. These are learners who told us they were placed, so treat them as a starting point, not as today's market rate. Salary data for EV roles: EV engineer salaries.

Free Power Electronics tutorials

Start here before you pay for anything. These are written by Skill-Lync learners and engineers:

Before you pay

Everything is simulation. The courses use MATLAB, Simulink, LTspice and Altium; none of them sends a kit or has you build, power up and measure a converter. Employers hiring for hardware roles will ask what you have built and tested, so plan a bench project of your own (a small buck or boost board, an oscilloscope, a load).

Hours differ more than weeks. Four of the five courses run 12 weeks, but Fundamentals of DC-DC Converters has 7 hours of video against 25 for the industrial converters course. Compare hours and projects, not weeks.

Do not buy overlapping courses. The PCB Overview course repeats buck, boost, rectifier and inverter basics that the DC-DC and EV simulation courses teach in more depth. If you plan to take the PG program, do not buy its four member courses separately first.

Two short workshops are left out. Power Electronics in EV Applications and Traction Inverter Hardware Design - Overview are 1-hour sessions, yet their pages show the same ₹40,000 as a 12-week course. Ask the counsellor what they include before paying for either.

No placement record from the power converter program yet. The five power electronics placements we hold all came from the EV program. Ask for recent placements in the exact role before paying for the PG program.

Power Electronics course FAQs

What is the fee for a power electronics course at Skill-Lync?

As of 20 Nov 2026: each of the five power electronics courses is ₹40,000. The Post Graduate Program in Power Converter Design and Analysis is ₹2,75,000 (EMI from ₹14,375 a month). Fees are inclusive of all charges.

Which software is used in power electronics?

MATLAB and Simulink (with Simscape Electrical) for converter models and control loops, LTspice for circuit-level simulation, PLECS and PSIM in many companies, and Altium Designer or KiCad for the PCB. The Skill-Lync courses use MATLAB, Simulink, LTspice and Altium. LTspice and KiCad are free.

What should I know before a power electronics course?

Circuit basics (Ohm's law, Kirchhoff's laws, how inductors and capacitors store energy), how diodes and transistors behave, and some MATLAB. Control theory helps for the modelling weeks; the DC-DC fundamentals course teaches Bode plots from scratch.

How long does it take to learn power electronics?

Each Skill-Lync course runs 6 to 12 weeks with 7 to 25 hours of video and 2 or 3 projects; the PG program runs 48 weeks. Being useful in a design team usually means a DC-DC course, a course on devices and losses or on rectifiers, and a small converter you have built and measured yourself.

Is power electronics a good career in India?

There is steady work in EV traction inverters and chargers, solar inverters, UPS and data-centre power supplies, and industrial drives. It is a hardware field: employers value bench experience. Skill-Lync's placement records include 5 power electronics or hardware design job titles (2022 to 2025, 2.8 to 4 LPA reported), all from the EV program.

What is the difference between power electronics and power systems?

Power systems is the grid: generation, transmission lines, faults, protection, load flow. Power electronics is the converters that connect things to the grid or to each other: chargers, inverters, drives, rectifiers. Skill-Lync's Introduction to Electric Power System course covers the grid side and is not part of this list.

Get the syllabus and fee plans

Talk to a counsellor.

Tell us your branch and year. We will send the syllabus for the Power Electronics course that fits and explain the payment plans.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.