Ćuk converter calculator (and SEPIC, Zeta)

Design the power stage of a Ćuk (Cuk), SEPIC or Zeta DC-DC converter: duty cycle with the diode drop, the two inductors for your ripple (and the coupled-inductor value), the coupling capacitor and its voltage, the output capacitor, the lightest load that stays in continuous conduction, switch and diode stresses, and both inductor currents drawn over two periods. Free, no sign-up, runs in your browser.

Ideal power stage + diode drop · CCM · formulas checked against a circuit simulation · Updated 17 Nov 2026

Ideal switch, diode with a fixed forward drop. Size the inductors at the highest input voltage (largest ripple) and check currents at the lowest.

Duty cycle D0.564CCM, |Vo|/Vin = 1.250
L1 = L2 each130.9 µHcoupled pair: 65.5 µH
0.00.51.01.505101520time (µs)current (A)━ iL1 ━ iL2 · shaded: switch on (D = 0.564)

    How does a Ćuk converter work?

    A Ćuk converter is a DC-DC converter that can step a voltage up or down and inverts it. Unlike a buck-boost converter, which stores energy in one inductor, it passes energy from input to output through a capacitor, C1, with an inductor on each side. That puts an inductor in series with both the input and the output, so both currents are smooth triangles instead of pulses.

    +−VinL1SC1DL2C2R−+Vo
    The Ćuk power stage. C1 sits at Vin + |Vo|; note the output polarity.
    • Switch on: L1 charges from the input. The switch grounds the left plate of C1, so C1 discharges into L2 and the load. The diode is reverse-biased.
    • Switch off: L1's current recharges C1 through the diode, while L2 keeps driving the load through the same diode.

    Volt-second balance on the two inductors gives the duty cycle, and charge balance on C1 gives the currents. VF is the diode's forward drop:

    How do you design a Ćuk converter?

    Five steps, all for continuous conduction (CCM). The same steps size a SEPIC or a Zeta; only the C1 voltage and the output capacitor change.

    1. Duty cycle from the formula above. Use the lowest input voltage for the largest D and current.
    2. Inductors. Allow a ripple of 20% to 40% of the input current and use the same value for both inductors, as Texas Instruments' SEPIC and ZETA design notes do. Two windings on one core (a coupled inductor) share the ripple, so each needs only half the inductance.
    3. Coupling capacitor. It carries the full load current while the switch is on, so choose its ripple ΔVC1, a few percent of VC1.
    4. Output capacitor. In a Ćuk or Zeta converter L2 feeds the output continuously, as in a buck. In a SEPIC the output gets pulses from the diode, as in a boost, and needs much more capacitance.
    5. Checks: the lightest load that stays in CCM, the switch and diode ratings, and the C1 resonance.

    Worked example: a 12 V to −15 V, 1 A Ćuk converter

    A negative rail for an op-amp or sensor supply from a 12 V input. Switching at 100 kHz, Schottky diode with VF = 0.5 V, 40% ripple, 5% ripple on C1 and 150 mV on the output:

    So two 130.9 µH inductors (or one 65.5 µH coupled pair) rated above 1.55 A and 1.26 A peak, a 4.18 µF coupling capacitor rated well above 27 V, and 4.31 µF at the output. The switch must block 27.5 V and carries 2.81 A at its peak (both inductor currents together); the diode blocks 27 V and carries the 1 A load on average.

    0.00.51.01.505101520time (µs)current (A)━ iL1 ━ iL2 · shaded: switch on (D = 0.564)
    Both inductor currents with L1 = L2 = 130.9 µH: iL1 (input) around 1.29 A and iL2 (output) around 1 A, each with 0.517 A ripple. Shaded: switch on, 56% of each 10 µs period.

    We simulated this circuit (ideal switch, 0.5 V diode, RK4, periodic steady state): output −14.999 V, C1 at 27.00 V, inductor ripples 0.517 A and 0.519 A, C1 ripple 1.35 V and output ripple 150.8 mV, against 0.517 A, 1.35 V and 150 mV by formula.

    When does a Ćuk converter go into discontinuous mode?

    In a Ćuk, SEPIC or Zeta converter the individual inductor currents can go negative without anything changing; what matters is the diode current, iL1 + iL2, during the off-time. When it falls to zero the converter is in discontinuous conduction (DCM), and the output no longer depends on D alone. The boundary depends on the two inductors in parallel:

    The example's Le is 65.5 µH, 4.4 times the limit, so it stays in CCM down to a load of 0.225 A. In the simulation, Le = 1.1 × Le,crit kept the diode conducting for the whole off-time in all three topologies, and 0.9 × Le,crit did not.

    Ćuk vs SEPIC vs Zeta converter

    Same duty-cycle relation, same switch and diode voltage (Vin + Vo, plus VF for the switch), same inductor and C1 ripple formulas. They differ in polarity, in which side has the smooth current, and in where C1 sits.

    ĆukSEPICZeta
    Output polarityInverted (negative)Same as inputSame as input
    Coupling capacitor voltageVin + VoVinVo
    Input currentContinuous (L1)Continuous (L1)Pulsed (switch)
    Output currentContinuous (L2)Pulsed (diode)Continuous (L2)
    Output capacitor C2ΔIL / (8 fs ΔVo)Io D / (fs ΔVo)ΔIL / (8 fs ΔVo)
    SwitchLow-sideLow-sideHigh-side
    Switch and diode voltageVin + VoVin + VoVin + Vo
    Typical useNegative rails; low ripple in and outBattery to a fixed rail, LED driversPositive rail with low output ripple
    +−VinL1SC1L2DC2R+−Vo
    SEPIC: L2 goes to ground and the diode feeds the output, so the output is positive but pulsed.
    +−VinSL1C1DL2C2R+−Vo
    Zeta: the switch is on the input side (high-side), L2 feeds the output as in a buck.

    SEPIC example: 9 V to 12 V at 2 A

    A SEPIC holds a 12 V rail from a battery that may sit above or below 12 V. At the low end, 9 V in, 250 kHz, 0.5 V diode: D = 0.581, input current 2.78 A, L1 = L2 = 18.8 µH, C1 = 10.3 µF on 9 V, and C2 = 38.8 µF for 120 mV. The output capacitor is 3.8 times C1 because the diode delivers current only during the off-time. Simulated output: 12.004 V, ripple 120.0 mV.

    Zeta example: 20 V to 12 V at 1.5 A

    200 kHz, 0.5 V diode: D = 0.385, input current 0.938 A, L1 = L2 = 102.6 µH, C1 = 4.81 µF on 12 V, and only 1.95 µF at the output for 120 mV because L2 smooths the output current. Simulated output: 11.991 V, ripple 120.2 mV.

    Why does the coupling capacitor need a resonance check?

    C1 and the two inductors form a resonant loop. The ripple formulas assume that loop rings much more slowly than the switching frequency. In our simulations, shrinking C1 to push its resonance up raised the error of the C1 ripple formula from under 0.5% to about 1% at fs/10 and to several percent beyond, so the calculator flags designs above fs/10:

    The Ćuk example sits at 4.8 kHz, 1/21 of fs. A bigger C1 or bigger inductors pull it lower; the loop's damping and its effect on the control loop need the full small-signal model.

    What this calculator does not cover

    • Losses. Only the diode drop is modelled. Switch, inductor and capacitor losses mean a real converter needs a slightly larger D and limit the useful gain.
    • Capacitor RMS current. C1 carries IL1 during the off-time and IL2 during the on-time, so its RMS current is √(Iin Io) (1.14 A in the Ćuk example; the same as TI's Iin√((1 − D)/D)). The calculator shows it; check the capacitor's ripple-current rating and the DC-bias derating of ceramics.
    • Inductor saturation. Rate each inductor (or the coupled pair) above its peak current with margin for load steps.
    • Control. These are fourth-order converters (the Ćuk and SEPIC also have a right-half-plane zero), so loop compensation needs a small-signal model.
    • DCM operation. Below the CCM limit the calculator says so but does not compute the DCM duty cycle.

    Use the results to size parts and see the trade-offs move, then confirm with the controller IC's datasheet and a bench test. For a single-inductor design, use the buck and boost converter calculator.

    Design power converters

    Skill-Lync's power electronics courses take you from these formulas to simulated and laid-out converters, the work EV and electronics teams hire for.

    Frequently asked questions

    What is the formula for the duty cycle of a Ćuk converter?

    With an ideal switch and diode, D = Vo / (Vin + Vo), so |Vo|/Vin = D/(1 − D) and the output is inverted. With the diode's forward drop VF: D = (Vo + VF)/(Vin + Vo + VF). Stepping 12 V to −15 V with a 0.5 V diode needs D = 0.564. SEPIC and Zeta converters use the same duty-cycle relation but keep the output positive.

    How do you calculate the inductors of a Ćuk or SEPIC converter?

    Pick the ripple current, 20% to 40% of the input current (the rule of thumb in TI's SEPIC and ZETA design notes), then L1 = L2 = Vin × D / (fs × ΔIL). For 12 V to −15 V at 1 A and 100 kHz with 40% ripple, ΔIL = 0.517 A and L = 130.9 µH each. Two windings on one core (a coupled inductor) need about half that: 65.5 µH.

    How do you choose the coupling capacitor in a Ćuk converter?

    C1 carries the load current while the switch is on, so its ripple is ΔVC1 = Io × D / (fs × C1). Choose a ripple of a few percent of its DC voltage, which is Vin + Vo in a Ćuk converter, Vin in a SEPIC and Vo in a Zeta. In the 12 V to −15 V example, C1 = 4.18 µF for 5% ripple on 27 V. It also carries a large RMS current, so low-ESR ceramic or film capacitors are used.

    What is the difference between Ćuk, SEPIC and Zeta converters?

    All three step up or down with the same duty-cycle relation and move energy through a coupling capacitor. The Ćuk inverts the output and has continuous current at both input and output. The SEPIC keeps the output positive with a continuous input current but a pulsed output current. The Zeta keeps the output positive with a continuous output current but a pulsed input current, and needs a high-side switch.

    Why is the output of a Ćuk converter negative?

    The coupling capacitor C1 charges to Vin + Vo with the switch-side plate positive. When the switch turns on it grounds that plate, so the other plate drops to −(Vin + Vo) and pulls current through L2 out of the output node. The load current flows from ground into the output, so the output voltage is negative.

    Is this calculator accurate?

    For an ideal power stage, yes: Skill-Lync checked every formula against a time-domain simulation of each switched circuit on 3 worked examples and 120 random designs (output voltage within 0.5%, inductor ripple within 0.1%, C1 ripple within 1.1%, output ripple within 1.5%). Real converters add losses, ESR, inductor saturation and control-loop effects, which the page lists.

    Related on Skill-Lync

    Sources

    • S. Ćuk and R. D. Middlebrook, "A new optimum topology switching dc-to-dc converter", IEEE Power Electronics Specialists Conference, 1977 (the original Ćuk converter).
    • N. Mohan, T. M. Undeland and W. P. Robbins, Power Electronics: Converters, Applications and Design, chapter 7, dc-dc switch-mode converters (the Ćuk converter's CCM relations).
    • R. W. Erickson and D. Maksimović, Fundamentals of Power Electronics, chapter 2 (volt-second and charge balance applied to the Ćuk converter).
    • J. Falin, "Designing DC/DC converters based on SEPIC topology", Texas Instruments Analog Applications Journal, 4Q 2008 (SLYT309), and "Designing DC/DC converters based on ZETA topology", 2Q 2010 (SLYT372): duty cycle with the diode drop, 20% to 40% ripple rule, equal and coupled inductors.
    • Worked examples and all their numbers: Skill-Lync, checked by scripts/verify/cuk.py, which simulates each switched circuit (ideal switch, diode with a fixed drop, RK4, 2,000 steps per period, periodic steady state by shooting) for the 3 examples and 120 random designs, plus the CCM/DCM boundary and the C1 resonance sweep, and is cross-checked against this page's calculator code at build time.
    Free counselling

    Go from formulas to working converters.

    Power electronics for EVs, chargers and electronics products is a hiring area for electrical engineers. A Skill-Lync counsellor can map the course that fits the role you want.

    Talk to a power electronics course counsellor

    Free. We call you back, usually the same day.

    By submitting you agree to our Terms and Privacy Policy.

    Talk to a career counsellor

    Talk to a career counsellor

    Free 20-minute call. We'll map the right course to where you want to work.

    By submitting you agree to our Terms and Privacy Policy.