Engineering Graphics cover
Interactive book · Semester 1-2

Engineering Graphics

Roll a circle to trace a cycloid, swing a line until its true length shows, slice a cone into an ellipse and unroll it flat

24 chapters, 24 interactives, few words. Every chapter is mapped to the Anna University, VTU, SPPU, Mumbai University and KTU units it covers: BIS conventions and scales, conics, cycloids, involutes, spirals and helices, projection of points, lines and planes, true length and traces, projection of solids, sections and true shapes, development of surfaces and transition pieces, orthographic, sectional and missing views, isometric, perspective and oblique projection, and CAD drafting.

  • AUGE3251Engineering Graphics
  • VTUBCEDK103/203Computer-Aided Engineering Drawing
  • SPPU102012Engineering Graphics
  • MUFEC204Engineering Graphics
  • KTUGMEST103Engineering Graphics and Computer Aided Drawing

By Skill-Lync · Updated 19 Nov 2026 · 24 chapters · 24 interactives · free, no sign-up

Chapter 1

Drawing sheets, lines, lettering and dimensioning to BIS conventions

Which syllabus covers thisAU GE3251 ConventionsVTU BCEDK103 Module 1SPPU 102012 Unit IMU FEC204 Module 1KTU GMEST103 Introduction

Why does a part still need a drawing when the CAD model exists?

A drawing is the contract between the designer, the shop floor and the inspector: it says what to make, to what size and how to check it, and it can be read by anyone trained in the same conventions without the software. In India those conventions are collected in BIS SP 46, which follows the ISO standards. One rule to fix early: SP 46 requires the first-angle method of projection for drawings made after 31 December 1991. Every chapter of this book uses first angle unless it says otherwise.

Where do the A0 to A4 sheet sizes come from, and how is a sheet laid out?

A0 has an area of 1 m² and sides in the ratio 1:√2, so it is 840.9 × 1189.2 mm, rounded to 841 × 1189. Halve the long side and you get the next size with the same shape: A1 594 × 841, A2 420 × 594, A3 297 × 420, A4 210 × 297, and 16 A4 sheets make one A0. IS 10711 leaves a 20 mm border on the left (the filing margin) and 10 mm on the other edges, a 180 mm wide title block sits in the bottom right corner, A0 to A3 are used horizontally and A4 vertically. Prints larger than A4 are folded to A4 with the title block on top.

Drawing sheet sizes A0 to A4, borders and title block, and the scale that fits your part: interactive loads as you scroll

Which type of line goes where?

SP 46 uses two widths in the ratio 1:2, for example 0.7 and 0.35 mm. Continuous wide: visible edges and outlines. Continuous narrow: dimension lines, projection (extension) lines, leader lines, hatching and short centre lines. Dashed narrow: hidden edges. Long-dashed dotted narrow: centre lines, lines of symmetry and pitch circles. The cutting plane is the same chain line made wide at its ends and where it changes direction. A narrow freehand or zigzag line marks where a view is broken off. Dashes are about 12 line widths long with gaps of 3.

How tall should lettering be, and how thick?

SP 46 lists nominal heights of 1.8, 2.5, 3.5, 5, 7, 10, 14 and 20 mm, each about √2 times the last, the same step as the paper sizes, so lettering stays legible when a drawing is enlarged or reduced from one A size to the next. Height h is the height of a capital letter. Type B, the preferred upright style, uses a stroke width of h/10 and lower-case letters 7/10 of h; type A is thinner at h/14. Letters may be vertical or sloped at 75°. Use single-stroke letters of uniform width.

What are the parts of a dimension, and what rules keep a drawing readable?

Projection lines carry the feature out of the view, a dimension line with a termination at each end spans the size, and the value sits above it near the middle; a leader points to a note. Arrowheads have an included angle between 15° and 90° (or use a 45° oblique stroke), one style per drawing. Values are either aligned with the dimension line and read from the bottom or right (Method 1) or all read from the bottom (Method 2), never mixed. Dimension each feature once, on the view that shows it most clearly, in mm without the unit, and avoid crossing lines. Chain, parallel and combined dimensioning differ in how errors add up.

Predict, then check

How many A4 sheets can be cut from one A0 sheet?

Worked examples

The A series from one rule · A0 has an area of 1 m² and its sides are in the ratio 1:√2; each next size halves the long side (rounded down to the mm)
  1. Short side x = 1000/2^(1/4) = 840.9 mm, long side y = 1000 × 2^(1/4) = 1189.2 mm, so A0 = 841 × 1189 mm
  2. A1: halve 1189 → 594, so 594 × 841; A2: halve 841 → 420, so 420 × 594
  3. A3: halve 594 → 297, so 297 × 420; A4: halve 420 → 210, so 210 × 297
  4. Check the shape: 297/210 = 1.414 and √2 = 1.414
  5. Drawing space of A3 (horizontal): 420 − 20 − 10 = 390 mm by 297 − 10 − 10 = 277 mm, as in IS 10711

Answer: A0 841 × 1189, A1 594 × 841, A2 420 × 594, A3 297 × 420, A4 210 × 297 mm; A4 = 0.0624 m², about 1/16 m²

Choosing the sheet and the scale · A cover plate 520 × 300 mm (illustrative). The view must fit the drawing space above a title block about 27 mm tall; recommended scales only
  1. A3 usable area: 390 × (277 − 27) = 390 × 250 mm; at 1:1 the 520 mm length does not fit
  2. At 1:2 the view is 260 × 150 mm, which fits A3
  3. A2 usable area: 564 × (400 − 27) = 564 × 373 mm; at 1:1 the 520 × 300 view fits
  4. On A4 (180 × 250 usable) the largest fitting recommended scale is 1:5: 104 × 60 mm, too small to dimension comfortably

Answer: A2 at 1:1 if full size is wanted, otherwise A3 at 1:2; SP 46 asks for the smallest sheet that still gives clarity

Line widths and lettering for one drawing · Line group 0.7 (wide 0.7 mm, narrow 0.35 mm), dimension values in type B lettering 5 mm tall, notes 3.5 mm
  1. Hidden line (dashed narrow, d = 0.35 mm): dashes 12d = 4.2 mm, gaps 3d = 1.05 mm
  2. Centre line (long-dashed dotted narrow): long dashes 24d = 8.4 mm, dots no longer than 0.5d = 0.175 mm
  3. 5 mm type B lettering: stroke h/10 = 0.5 mm, lower case 0.7h = 3.5 mm, spacing 0.2h = 1.0 mm
  4. 3.5 mm notes: stroke 3.5/10 = 0.35 mm, the same as the narrow line

Answer: Visible edges 0.7 mm; dimension, hidden and centre lines 0.35 mm; lettering strokes 0.5 and 0.35 mm

Chapter 2

Scales: representative fraction, plain, diagonal and vernier scales

Which syllabus covers thisAU not in syllabusVTU BCEDK103 Module 1SPPU not in syllabusMU FEC204 Module 1KTU not in syllabus

What is the representative fraction, and which scales should a drawing use?

The representative fraction RF is the length on the drawing divided by the true length, both in the same unit. RF 1 is full size; 1/2, 1/5 or 1/100 are reducing scales; 2, 5 or 10 are enlarging scales for small parts. SP 46 recommends 50:1, 20:1, 10:1, 5:1, 2:1, 1:1 and 1:2, 1:5, 1:10 down to 1:10000, written as SCALE 1:2 in the title block. A map that says 1 cm = 1 km has RF 1/1,00,000.

How is a plain scale built and read?

First the length of the scale: RF × the longest length to be measured. To measure up to 6 m at 1:40 the scale is 6000/40 = 150 mm. Divide it into 6 main units of 25 mm (one per metre), divide the first main unit into 10 subunits (decimetres), and put the zero at the end of the first main unit: metres are numbered to the right, decimetres to the left. A plain scale reads two units, here metres and decimetres, so its least count is 1 dm. Write the RF and the units below it.

How does a diagonal scale read a third unit?

Draw 10 equal horizontal spaces above the plain scale and, in the first main unit, join each bottom subunit point to the next point along the top. These diagonals are the trick: by similar triangles, on the k-th horizontal line a diagonal has moved k/10 of a subunit. So for 3.47 m, put one divider point where the 3 m line crosses horizontal 7 and the other where diagonal 4 crosses it. The scale reads metres, decimetres and centimetres, a least count of 1/100 of a main unit.

Plain and diagonal scales: build one for any representative fraction and read a length off it: interactive loads as you scroll

What do forward and backward vernier scales do?

A vernier reads a fine unit by comparing two slightly different divisions. Its least count is the difference between 1 main scale division and 1 vernier division. In a forward vernier, 10 vernier divisions span 9 main divisions, so with a 1 mm main division the least count is 0.1 mm, and the vernier is numbered the same way as the main scale. In a backward vernier, 10 vernier divisions span 11 main divisions and the vernier is numbered the other way. A scale of chords (an arc divided into degrees) is a related tool for setting out angles without a protractor.

Predict, then check

A line measures 48 mm on a drawing at scale 1:5. What is its true length?

Worked examples

Plain scale for a room layout · 1 cm on the drawing represents 0.5 m (illustrative); lengths up to 8 m; show 5.7 m
  1. RF = 1 cm / 0.5 m = 10 mm / 500 mm = 1/50
  2. Length of scale = 8000 × 1/50 = 160 mm, divided into 8 main units of 20 mm (metres)
  3. First main unit divided into 10 subunits of 2 mm (decimetres); zero at its right end
  4. 5.7 m: from the 5 m mark to the 7th decimetre left of zero, 114 mm on paper

Answer: A 160 mm scale reading metres and decimetres; 5.7 m spans 114 mm

Diagonal scale for a map · A map at RF 1/50,000 (illustrative); a scale to read km, hm and dam up to 12 km; show 7.46 km
  1. Length of scale = 12 km × 1/50,000 = 12,000,000 mm / 50,000 = 240 mm, 12 main units of 20 mm
  2. First main unit split into 10 subunits of 2 mm (hm); 10 horizontal spaces above; diagonals from each bottom point to the next top point
  3. On the 6th horizontal line a diagonal has moved 6/10 × 2 = 1.2 mm: that is 6 dam
  4. 7.46 km: from the 7 km line to diagonal 4, along horizontal 6: 7 × 20 + 4.6 × 2 = 149.2 mm
  5. Check: 7.46 km × 1/50,000 = 149.2 mm

Answer: A 240 mm diagonal scale with a least count of 1 dam (0.2 mm on paper); 7.46 km spans 149.2 mm

Backward vernier on a plan · RF 1/25 (illustrative); main scale divisions of 1 dm; 10 vernier divisions span 11 main divisions; show 2.37 m
  1. 1 MSD = 100 mm × 1/25 = 4 mm on paper; 1 VSD = 11 × 4/10 = 4.4 mm
  2. Least count = VSD − MSD = 0.4 mm on paper = 10 mm = 1 cm true
  3. 2.37 m = 237 cm: take 7 VSD (77 cm) and the rest, 160 cm, as 16 MSD
  4. Divider length = 7 × 4.4 + 16 × 4 = 94.8 mm = 2370 mm × 1/25

Answer: Least count 1 cm; 2.37 m is 7 vernier divisions plus 16 main divisions, 94.8 mm on paper

Chapter 3

Conics by the eccentricity method: ellipse, parabola and hyperbola, with tangents and normals

Which syllabus covers thisAU GE3251 Unit IVTU not in syllabusSPPU 102012 Unit IIIMU not in syllabusKTU not in syllabus

What makes a curve an ellipse, a parabola or a hyperbola?

Take a fixed point, the focus F, and a fixed line, the directrix. A conic is the path of a point P whose distance from the focus divided by its distance from the directrix is a constant e, the eccentricity. If e < 1 the curve closes into an ellipse, if e = 1 it is a parabola, and if e > 1 it is a hyperbola. The same three curves appear when a plane cuts a cone: across all the generators (ellipse), parallel to one generator (parabola), or steeper, cutting both halves (hyperbola). Chapter 15 cuts the cone.

How is a conic drawn by the eccentricity method?

Draw the directrix and the axis through F at right angles, meeting at C. Divide CF at the vertex V so that VF/VC = e: with CF = 60 mm and e = 2/3, VC = 36 and VF = 24 mm. At V draw VE = VF at right angles and join CE: this e-line rises e mm for every mm from the directrix. Any vertical at distance x from the directrix meets it at height e·x. An arc of that radius about F cuts the vertical at two points with PF = e·PD. Repeat and join the points smoothly.

Ellipse, parabola and hyperbola by the eccentricity method, with the tangent and normal at any point: interactive loads as you scroll

How are the tangent and normal at a point found?

Join P to the focus F. At F draw a line at right angles to PF; it meets the directrix at T. The line PT is the tangent at P, and the normal is the line through P at right angles to PT. The method works for all three conics. At the vertex PF lies along the axis, so FT runs parallel to the directrix and never meets it: the tangent at the vertex is parallel to the directrix.

Where do engineers meet these curves?

Planets move on ellipses with the Sun at a focus. Earth's eccentricity is only 0.0167, so its orbit is 0.99986 as wide as it is long, almost a circle. A parabola sends every ray from its focus out parallel to its axis, which is why headlamp reflectors and dish antennas are paraboloids. A projectile without air drag follows a parabola. Plot pV = constant for a gas at constant temperature and you get a rectangular hyperbola, and cooling towers are hyperboloids: their curved surface can be built from straight members.

Predict, then check

The focus is 60 mm from the directrix and e = 2/3. How far is the vertex from the directrix?

Worked examples

Ellipse by the eccentricity method · Focus 60 mm from the directrix, eccentricity 2/3 (illustrative)
  1. Vertex: VC = 60/(1 + 2/3) = 36 mm, VF = 24 mm; draw VE = 24 mm at right angles and join CE
  2. Vertical at 50 mm from the directrix: the e-line is 33.33 mm high there
  3. Arc of radius 33.33 about F cuts that vertical at ±√(33.33² − 10²) = ±31.80 mm from the axis
  4. The far vertex is where PF = e·PD on the far side of F: x = 60/(1 − 2/3) = 180 mm, so the major axis is 180 − 36 = 144 mm
  5. At the centre (x = 108 mm) the construction gives half the minor axis: 53.67 mm

Answer: Major axis 144 mm, minor axis 107.3 mm, centre 108 mm from the directrix

Parabola and its tangent by the focus method · Focus 40 mm from the directrix, e = 1; tangent at the point 60 mm from the directrix (illustrative)
  1. Vertex midway: VC = VF = 20 mm; the e-line is at 45°
  2. Vertical at 60 mm: radius 60 about F gives P at ±√(60² − 20²) = ±56.57 mm
  3. Join PF; at F draw FT ⟂ PF to meet the directrix at T, 14.14 mm from C (same side as P)
  4. PT is the tangent: it makes 35.26° with the axis; the normal is at right angles to it at P

Answer: P is 56.57 mm from the axis; the tangent cuts the directrix 14.14 mm from C, at 35.3° to the axis

Hyperbola by the eccentricity method · Focus 50 mm from the directrix, e = 1.5 (illustrative)
  1. Vertex: VC = 50/2.5 = 20 mm, VF = 30 mm
  2. The e-line rises 1.5 mm per mm: at 60 mm from the directrix it is 90 mm high
  3. Arc of radius 90 about F cuts the 60 mm vertical at ±√(90² − 10²) = ±89.44 mm
  4. The branch opens out; far away it runs along its asymptotes at arctan √(e² − 1) = 48.2° to the axis

Answer: Vertex 20 mm from the directrix; at 60 mm the curve is 178.9 mm wide

Chapter 4

Other conic constructions: concentric circles, oblong, arcs of circles, rectangle and the rectangular hyperbola

Which syllabus covers thisAU GE3251 Unit IVTU not in syllabusSPPU 102012 Unit IIIMU not in syllabusKTU not in syllabus

How do two circles give an ellipse?

Draw circles on the major axis and the minor axis as diameters, from the same centre. Divide them into 12 equal parts with radial lines. Where a radial line cuts the large circle, draw a vertical; where it cuts the small circle, draw a horizontal. They meet on the ellipse, because the point is (a cos t, b sin t). Twelve points and the four axis ends are enough to draw a smooth curve by hand. This is the quickest exact method when both axes are given.

Other ways to draw conics: concentric circles, oblong, arcs of circles, the rectangle method and pV = c: interactive loads as you scroll

How do the oblong and arcs-of-circles methods work, and where are the foci?

Oblong: draw the rectangle that holds the ellipse, divide the half major axis and the short side of the rectangle into equal parts counted from the axis end, and join each division from the two ends of the minor axis; matching lines cross on the curve. Arcs of circles: the foci are where an arc of radius a, half the major axis, from the end of the minor axis cuts the major axis; for 120 × 70 mm they are 48.7 mm from the centre. Any point on the curve has PF1 + PF2 = 2a, so arcs of radii r and 2a − r about the two foci cross on it.

How is a parabola drawn from its span and rise?

Rectangle method: draw the rectangle of the span and the rise with the vertex at the middle of one long side. Divide half that side, from the vertex, and the short side, from the vertex end, into the same number of equal parts. Lines from the vertex to the points on the short side meet the lines parallel to the axis through the matching points. Tangent method: the tangents at the two base ends meet on the axis at twice the rise; divide both into equal parts, number one forwards and one backwards, and join matching numbers. The joins wrap the parabola.

What is a rectangular hyperbola, and how is it drawn?

It is the curve xy = constant, a hyperbola whose asymptotes are at right angles; its eccentricity is √2. Given the asymptotes and one point P0, draw lines through P0 parallel to both asymptotes. Mark points on the line parallel to the vertical asymptote, join each to the origin and extend to the other line. A vertical from that crossing and a horizontal from the marked point meet on the curve, because similar triangles keep x·y equal to that of P0. Boyle's law, pV constant, plots as this curve.

How is the tangent drawn at a point of these curves?

Ellipse: join P to both foci; the normal bisects the angle F1PF2 and the tangent is at right angles to it. That is also why a ray from one focus reflects through the other. Parabola: the tangent bisects the angle between PF and the perpendicular from P to the directrix. Rectangular hyperbola: the tangent at P cuts each asymptote at twice P's distance along it, so P is the midpoint of the tangent between the asymptotes.

Predict, then check

An ellipse has a major axis of 120 mm and a minor axis of 72 mm. How far from the centre are the foci?

Worked examples

Ellipse by arcs of circles · Major axis 130 mm, minor axis 78 mm (illustrative); one point from the division 20 mm inside F1
  1. Foci: an arc of radius 65 mm from the minor-axis end cuts the major axis at √(65² − 39²) = 52 mm from the centre
  2. Mark point 1 at 20 mm from F1 towards the centre: A1 = (65 − 52) + 20 = 33 mm, B1 = 130 − 33 = 97 mm
  3. Arc of 33 mm about F1 and of 97 mm about F2 meet at 40.0 mm left of the centre, 30.74 mm from the axis (and its mirror points)
  4. Check: 40²/65² + 30.74²/39² = 1.000
  5. Tangent there: bisect the angle F1PF2 for the normal; the tangent makes 25.1° with the major axis

Answer: Foci 52 mm from the centre; the point is (−40.0, ±30.74) mm; tangent at 25.1° to the major axis

A parabolic arch by the rectangle method · An arch opening 4 m wide and 1.2 m high (illustrative), drawn at 1:50, half-side divided into 4
  1. Rectangle: 4000/50 = 80 mm by 1200/50 = 24 mm, vertex at the middle of the top side
  2. Divide the 40 mm half-side from the vertex and the 24 mm side from the top into 4 parts each
  3. Point 2: the vertical 20 mm from the vertex meets the line to side point 2 at 6 mm below the vertex = 24 × (2/4)²
  4. The focus is B²/(16H) = 80²/(16 × 24) = 16.67 mm below the vertex, 0.83 m on the real arch

Answer: Points at 1.5, 6, 13.5, 24 mm below the vertex line; focus 16.7 mm below the vertex on the drawing

Expansion line pV = constant · A gas at 4 bar and 0.3 m³ expands at constant temperature (illustrative); plot to 1 bar = 10 mm, 0.1 m³ = 10 mm
  1. P0 is at (30, 40) mm from the axes; pV = 4 × 0.3 = 1.2 bar m³
  2. For 2 bar: mark 20 mm up the vertical through P0, join to O and extend to the 40 mm line: x′ = 30 × 40/20 = 60 mm, so V = 0.6 m³
  3. Likewise 8 bar gives 0.15 m³ and 1.5 bar gives 0.8 m³
  4. Tangent at (0.6 m³, 2 bar) cuts the volume axis at 1.2 m³ and the pressure axis at 4 bar: twice each coordinate

Answer: A rectangular hyperbola through (0.3, 4), (0.6, 2), (0.15, 8) and (0.8, 1.5); pV = 1.2 bar m³ everywhere

Chapter 5

Cycloid, epicycloid, hypocycloid and trochoids

Which syllabus covers thisAU GE3251 Unit IVTU not in syllabusSPPU 102012 Unit IIIMU FEC204 Module 1KTU not in syllabus

What is a cycloid, and how do you draw one?

Mark a point on the rim of a wheel and roll the wheel along a straight line without slipping: the point traces a cycloid. One revolution moves the centre forward by the circumference, so the base of one arch is πD. To draw it, divide the circle and the base into 12 equal parts, mark the 12 positions of the centre, and through each division point of the circle draw a line parallel to the base. Swing an arc of radius r from each centre position to cut the matching line. For D = 48 mm the base is 150.8 mm, each step 12.57 mm.

Cycloid, epicycloid and hypocycloid traced by a rolling circle, with the normal through the contact point: interactive loads as you scroll

What changes when the circle rolls on another circle?

Rolling outside a directing circle of radius R gives an epicycloid; rolling inside gives a hypocycloid. The base is now an arc, and one revolution of the rolling circle covers an angle θ = 360 r/R at the directing centre: 90° for r = 20 mm on R = 80 mm. The centre moves on a circle of radius R + r (outside) or R − r (inside). One special case is worth seeing: when R = 2r the hypocycloid is a straight line, a diameter of the directing circle. Cycloidal gear teeth, still used in clocks and watches, have epicycloid tips and hypocycloid roots.

What are trochoids?

If the tracing point is not on the rim the curve is a trochoid. A point inside the circle, like a reflector clipped to a bicycle spoke, traces an inferior (curtate) trochoid: a smooth wave that never touches the base. A point outside the rolling circle, like the flange of a railway wheel that reaches below the top of the rail, traces a superior (prolate) trochoid with small loops: for a moment that part of the wheel moves backwards. The same two cases exist for epicycloids and hypocycloids (epitrochoids and hypotrochoids).

How do you draw the tangent and normal at a point on a cycloid, and why does it work?

At any instant the rolling circle pivots about its contact point with the base, so every point of the circle moves at right angles to the line joining it to that contact point. Hence the normal at P passes through the contact point. With P as centre and radius r, cut the locus of centres at C; drop a perpendicular from C to the base at N. PN is the normal, and the tangent is drawn through P at 90° to it. The cycloid is also the brachistochrone: a bead sliding without friction gets from one point to a lower one fastest along an upside-down cycloid.

Predict, then check

A wheel of diameter 600 mm rolls exactly one turn along a road. How far does a point on its rim travel along its own path?

Worked examples

A cycloid by the 12-division construction · A circle of 48 mm diameter rolls on a straight line for one revolution. Draw the cycloid traced by a point P on its rim, starting at the contact point (illustrative size).
  1. Draw the base: π × 48 = 150.80 mm long, and divide it into 12 parts of 12.566 mm.
  2. Draw the circle on the start of the base, divide it into 12 at 30°, and draw a horizontal line through each division point.
  3. Draw the locus of the centre 24 mm above the base and mark the 12 centre positions above the base divisions.
  4. From centre 3 swing an arc of 24 mm to cut the line through division 3: P3 is 13.70 mm along and 24 mm up (r(φ − sin φ), r(1 − cos φ) with φ = 90°).
  5. Centre 6 gives the top point P6, 75.4 mm along and 48 mm up; join all 13 points with a smooth curve.
  6. Check: the arch is 8r = 192 mm long and the area under it is 3πr² = 5,429 mm².

Answer: Base 150.8 mm, height 48 mm, arch length 192 mm

An epicycloid on a 160 mm directing circle · A circle of 40 mm diameter rolls outside a directing circle of 160 mm diameter for one revolution (illustrative sizes).
  1. Angle covered at the directing centre: θ = 360 × r/R = 360 × 20/80 = 90°.
  2. Divide this 90° arc and the rolling circle into 12 parts: 7.5° per step on the directing circle.
  3. The rolling centre moves on an arc of radius R + r = 100 mm; mark its 12 positions on the radial lines.
  4. Through each division point of the rolling circle draw an arc centred at the directing centre; cut it with an arc of 20 mm from the matching centre position.
  5. The curve rises to 120 mm from the directing centre (R + 2r) at the middle of the arch.
  6. Check: the directing arc rolled over is 125.66 mm, equal to the rolling circumference πd; one arch is 8r(R + r)/R = 200 mm long.

Answer: θ = 90°, arch length 200 mm, highest point 120 mm from the centre

Tangent and normal on a cycloid · A cycloid is traced by a circle of 24 mm radius. Draw the normal and tangent at the point P, 36 mm above the base on the rising half (illustrative).
  1. P is where the circle has turned through φ with 24(1 − cos φ) = 36, so cos φ = −0.5 and φ = 120°; P lies 29.48 mm along the base.
  2. With P as centre and radius 24 mm, cut the locus of centres at C.
  3. Drop a perpendicular from C to the base at N, 50.27 mm along: N is the contact point at that instant.
  4. PN is the normal, 41.57 mm long (= 2r sin(φ/2)).
  5. Draw the tangent through P at 90° to PN; it makes 30° with the base.

Answer: Normal PN = 41.57 mm, tangent at 30° to the base

Chapter 6

Involutes of a circle, a square and a polygon, and why gear teeth use them

Which syllabus covers thisAU GE3251 Unit IVTU not in syllabusSPPU 102012 Unit IIIMU FEC204 Module 1KTU not in syllabus

What is an involute?

Wrap a string round a base, a circle or a polygon, and unwind it while keeping it taut: its free end traces an involute. Two facts fix the curve. The free part of the string always touches the base, and its length equals the length unwound. So after one full turn off a circle of 42 mm diameter the string is πD = 131.9 mm long. To draw it, divide the circle into 12, draw tangents at the division points and lay off 1/12, 2/12 ... of πD along them; the ends lie on the involute.

Involute of a circle, square or polygon: unwind the string and watch the normal stay tangent to the base: interactive loads as you scroll

How is the involute of a square or a polygon different?

A polygon has no smooth edge to roll off, so the string swings about one corner at a time. Each piece of the involute is a circular arc centred at a corner, and the radius grows by one side at every corner: a, 2a, 3a and so on. Each arc turns through the exterior angle, 90° for a square, 120° for a triangle, 60° for a hexagon. For a square of side 25 mm the arcs have radii 25, 50, 75 and 100 mm, and the whole curve is 392.7 mm long.

Where are the normal and the tangent at a point of an involute?

The taut string is the normal. While it unwinds, the string pivots about the point where it leaves the base, so the end moves at right angles to the string. For a circle, find that point by drawing a semicircle on OP (O the centre): it cuts the base circle at T, and angle OTP is 90°, so PT is tangent to the base and is the normal at P. The tangent at P is at 90° to PT. The radius of curvature at P is the length PT: after 120° on a 42 mm circle, 44.0 mm.

Why do most gear teeth have involute flanks?

Two involute teeth in mesh always touch on one straight line, the common tangent of the two base circles, called the line of action. The force between them stays along that line, so the speed ratio stays constant through the mesh, and it does not change if the shafts sit a little further apart than designed. That makes involute gears forgiving to make and mount. The angle between the line of action and the common tangent at the pitch point is the pressure angle: most stock gears use 20°, with 14½° and 25° much less common. Base circle diameter = pitch diameter × cos 20°.

Predict, then check

A taut string is unwound through half a turn (180°) from a cylinder of 30 mm diameter. How long is the free string?

Worked examples

Involute of a circle · Draw the involute of a circle of 42 mm diameter for one turn, and find the distance of the point P from the centre after 120° (illustrative size).
  1. Length of string for one turn: π × 42 = 131.95 mm; divide it into 12 parts of 10.996 mm.
  2. Divide the circle into 12 at 30° and draw the tangent at each division point, all in the same sense round the circle.
  3. On the tangent at division 4 (120°) mark 4 × 10.996 = 43.98 mm; repeat for every division and join the ends.
  4. P after 120° is √(R² + PT²) = √(21² + 43.98²) = 48.74 mm from the centre.
  5. After the full turn the end is √(21² + 131.95²) = 133.6 mm from the centre.

Answer: PT = 43.98 mm and OP = 48.74 mm at 120°; string 131.9 mm after one turn

Involute of a square · A string is wound round a square of side 25 mm, one end at a corner A. Draw the involute traced as the whole string is unwound (illustrative size).
  1. Name the corners A, B, C, D going round the way the string is wound; produce each side beyond the corner ahead of it.
  2. Centre B, radius AB = 25 mm: swing a 90° arc from A to the produced side CB.
  3. Centre C, radius 50 mm: swing the next 90° arc to the produced side DC.
  4. Centre D, radius 75 mm, then centre A, radius 100 mm: two more 90° arcs.
  5. The last arc ends on side AB produced, 100 mm (the perimeter) from A. Total curve length = (π/2)(25 + 50 + 75 + 100) = 392.7 mm.

Answer: Four quarter arcs of radii 25, 50, 75 and 100 mm, total length 392.7 mm

Base circle and flank of a gear tooth · A spur gear has 36 teeth, module 3 mm and a 20° pressure angle; its tip diameter is 114 mm (illustrative gear).
  1. Pitch diameter d = m z = 3 × 36 = 108 mm.
  2. Base circle diameter = 108 × cos 20° = 101.49 mm: the tooth flank is the involute of this circle.
  3. At the pitch circle the string length (radius of curvature of the flank) is √(54² − 50.74²) = 18.47 mm, which equals 54 sin 20°.
  4. At the tip circle (radius 57 mm) it is √(57² − 50.74²) = 25.96 mm, unwound through 29.3° of the base circle.

Answer: Base circle 101.49 mm; flank radius of curvature 18.47 mm at the pitch circle, 25.96 mm at the tip

Chapter 7

Archimedean spiral and the helix on a cylinder and a cone

Which syllabus covers thisAU not in syllabusVTU not in syllabusSPPU 102012 Unit IIIMU FEC204 Module 1KTU not in syllabus

What is an Archimedean spiral and how is it constructed?

A point moves out along a line at a steady speed while the line turns about a fixed pole at a steady speed. Equal turns give equal steps out: r = aθ, so successive turns are one pitch apart on any ray. To draw two turns reaching 72 mm, the pitch is 36 mm; draw 12 radial lines and step the radius by 3 mm on each. The scroll of a lathe's self-centring chuck and the groove of a gramophone record follow it closely. A cam with this profile lifts its follower by equal amounts for equal turns, a uniform rise. A logarithmic spiral instead grows by the same ratio per turn.

What is a helix, and why does it unroll into a straight line?

A point that goes round a cylinder at a steady rate while moving along its axis at a steady rate traces a helix. The rise per turn is the pitch. In the front view the helix is a wave whose rear half is hidden, so it is drawn dashed; in the top view it is just the circle. Unroll the cylinder into a rectangle πD wide: each turn becomes a straight line rising one pitch, so the helix makes a constant angle ψ with the base. On a 50 mm cylinder with a 40 mm pitch, ψ = 14.3° and one turn is 162.1 mm long.

Archimedean spiral and the helix on a cylinder and a cone, and why a helix develops into a straight line: interactive loads as you scroll

How is a helix on a cone drawn?

On a cone the point still turns at a steady rate and rises at a steady rate, but the radius shrinks as it climbs. Divide the base circle into 12 and the height of each turn into 12; join each division of the base to the apex to get 12 generators. The point lies on generator k at height k/12 of a pitch. Its top view is an Archimedean spiral, since the radius falls by the same step for every 30°: on a cone 60 mm across and 90 mm tall with 3 turns, by 10 mm per turn.

Where do helices appear in engineering?

Screw threads, coil springs, helical gears, drill flutes and spiral staircases are all helices. Most hardware screw threads are right-handed: with the axis vertical, the visible strands rise from left to right. For a screw of 12 mm diameter with a 1.5 mm pitch (illustrative) the thread rises at only 2.3° to the base. A shallow angle like this, helped by friction, lets a screw hold a load without turning back; one turn of thread is 37.7 mm long.

Predict, then check

The pitch of a helix on a 40 mm cylinder is doubled from 20 mm to 40 mm. The helix angle with the base

Worked examples

An Archimedean spiral of two turns · A point moves out from the pole O to 72 mm while its line turns through two full turns at a steady rate (illustrative).
  1. Pitch (rise per turn) = 72/2 = 36 mm; with 12 divisions per turn each 30° adds 3 mm.
  2. Draw 12 radial lines at 30° and concentric circles at 3, 6, 9 ... 72 mm.
  3. Mark the point where line k meets circle k: at 210° (k = 7) the radius is 21 mm; join the 24 points smoothly.
  4. The spiral constant a = pitch/2π = 5.730 mm per radian.
  5. Length of the curve: (a/2)[θ√(1 + θ²) + sinh⁻¹θ] with θ = 4π gives 463.1 mm.

Answer: Pitch 36 mm, 3 mm per 30°, curve 463.1 mm long

Helix on a cylinder and its development · Draw two turns of a helix of pitch 40 mm on a cylinder of 50 mm diameter standing on the HP, and its development (illustrative).
  1. Draw the TV (a 50 mm circle) and divide it into 12; project the points up to the FV.
  2. Divide each 40 mm pitch into 12 parts of 3.33 mm; the point on generator k sits at height k × 3.33 mm.
  3. Join the points: the half in front of the axis is visible, the half behind is dashed.
  4. Develop the surface: a rectangle 157.1 mm (πD) by 80 mm; each turn is a diagonal rising 40 mm.
  5. Helix angle tan ψ = 40/157.1, ψ = 14.29°; one turn = √(40² + 157.1²) = 162.1 mm.

Answer: ψ = 14.29°, one turn 162.1 mm, two turns 324.2 mm

Helix on a cone · A cone with a 60 mm base and 90 mm height stands on the HP. A point goes round it 3 times from the base to the apex at a steady rate (illustrative).
  1. Pitch along the axis = 90/3 = 30 mm; the radius falls by 30/3 = 10 mm per turn.
  2. Divide the base circle into 12 and draw the 12 generators in both views.
  3. Divide the height into 36 parts of 2.5 mm; the point on generator k is at height k × 2.5 mm, and its TV lies on the matching radial line.
  4. Half way up (1.5 turns) the radius is 15 mm; the TV of the helix is an Archimedean spiral, pitch 10 mm.
  5. Length of the helix (numerical integration): 306.5 mm.

Answer: TV: Archimedean spiral, 10 mm per turn; helix length 306.5 mm

Chapter 8

Orthographic projection: reference planes, the four quadrants, first and third angle, and projection of points

Which syllabus covers thisAU GE3251 Unit IIVTU BCEDK103 Module 1SPPU 102012 Unit IVMU FEC204 Module 2KTU GMEST103 Module 1

What is orthographic projection, and what are the reference planes?

Orthographic projection draws an object as if seen from infinitely far away: every projector is parallel to the others and perpendicular to the plane of projection, so sizes parallel to the plane come out true. Two planes are used first: the vertical plane VP, which receives the front view, and the horizontal plane HP, which receives the top view. They meet in a line called XY, the reference line on every drawing. A profile plane at right angles to both gives the side views.

What are the four quadrants, and where do the views of a point land in each?

The HP and VP cross along XY and divide space into four quadrants: 1st above HP and in front of VP, 2nd above and behind, 3rd below and behind, 4th below and in front. To draw, the HP is turned about XY until it lies in the plane of the VP, its front half going down. Then the front view a′ sits above XY if the point is above the HP, and the top view a sits below XY if the point is in front of the VP. In the 2nd and 4th quadrants both land on the same side and the views overlap, so drawings use the 1st or 3rd.

Projection of a point in the four quadrants: rotate the HP open and see where the views land, then an L block in first and third angle: interactive loads as you scroll

What is the difference between first-angle and third-angle projection?

In first angle the object sits between the observer and the plane, so each view is pushed onto the plane behind it: the top view goes below the front view, and the view from the left goes on the right. In third angle the plane, imagined transparent, is between the observer and the object: the top view goes above and the view from the left on the left. The views themselves are identical, only their places swap. The method is shown by a truncated-cone symbol in the title block. Indian standard SP 46 requires first angle for drawings made after 31 December 1991; the United States and Japan mostly use third angle.

How are the projections of a point named and measured?

A point in space is named with a capital letter, A. Its top view is a, its front view a′ (a dash) and its side view a″. a′ and a always lie on one projector, a line at right angles to XY. The distance of a′ from XY is the height of A above or below the HP; the distance of a from XY is its distance in front of or behind the VP. A point on the HP has its front view on XY; a point on the VP has its top view on XY.

Predict, then check

A point is 20 mm below the HP and 30 mm in front of the VP. After the HP is opened out, where are its views?

Worked examples

Points in all four quadrants · A is 25 mm above HP and 35 mm in front of VP; B 15 mm above HP and 20 mm behind VP; C 30 mm below HP and 10 mm behind VP; D 20 mm below HP and 40 mm in front of VP. Draw their projections on one XY line (own numbers).
  1. Draw XY and four projectors at right angles to it, a few centimetres apart.
  2. A (1st quadrant): a′ 25 mm above XY, a 35 mm below XY.
  3. B (2nd quadrant): b′ 15 mm above XY, b 20 mm above XY: both above, the views overlap.
  4. C (3rd quadrant): c′ 30 mm below XY, c 10 mm above XY.
  5. D (4th quadrant): d′ 20 mm below XY, d 40 mm below XY: both below, the views overlap.

Answer: Only A and C keep the two views on opposite sides of XY

Distance of a point from XY · A point P is 30 mm above the HP and 40 mm in front of the VP. Find the length of its projector on the drawing and the true distance of P from the line XY (own numbers).
  1. p′ is 30 mm above XY and p is 40 mm below XY on the same projector.
  2. Length of the projector p′p on the drawing = 30 + 40 = 70 mm.
  3. In space, P, its foot on the HP and its foot on the VP make a rectangle with XY at one corner.
  4. True distance of P from XY = √(30² + 40²) = 50 mm (seen true in a side view).

Answer: Projector 70 mm on the drawing; P is 50 mm from XY

Reading a point and a layout back from the drawing · (a) a′ is 18 mm below XY and a is 26 mm above XY. (b) An L block 40 × 30 × 20 mm (leg 10 mm thick) is drawn in front view, top view and the view from the left with 16 mm between views (own numbers).
  1. (a) a′ below XY: the point is 18 mm below the HP. a above XY: it is 26 mm behind the VP. So it is in the 3rd quadrant.
  2. (a) Its distance from XY is √(18² + 26²) = 31.62 mm.
  3. (b) First angle: top view below the front view, view from the left to the right of it; third angle: top view above, view from the left to the left.
  4. (b) Either way the three views need 76 mm × 66 mm of sheet (40 + 16 + 20 by 30 + 16 + 20); one hidden line, 10 mm above the base, appears in the side view.

Answer: (a) 3rd quadrant, 18 mm below HP, 26 mm behind VP, 31.62 mm from XY; (b) 76 × 66 mm

Chapter 9

Lines parallel, perpendicular and inclined to one reference plane

Which syllabus covers thisAU GE3251 Unit IIVTU BCEDK103 Module 1SPPU 102012 Unit IVMU FEC204 Module 2KTU GMEST103 Module 1

How is a line named on a drawing, and what do θ, φ, α and β stand for?

A line AB is drawn through its two ends, each projected like a point. In first angle the front view a′b′ sits above XY and the top view ab below it, and a vertical projector joins a′ to a and b′ to b. θ is the true angle the line makes with the HP and φ the true angle with the VP. α and β are the angles a′b′ and ab make with XY on paper: the apparent angles. If A is 20 mm above the HP and 30 mm in front of the VP, a′ is 20 mm above XY and a is 30 mm below it.

What do the views look like when a line is parallel to both planes, or perpendicular to one?

Parallel to both planes: both views are parallel to XY and both show the true length. Perpendicular to the HP (a vertical rod): the front view is a vertical line of true length and the top view shrinks to a point. The end nearer the observer hides the other, so the point is written b(a), with the hidden end in brackets. Perpendicular to the VP (a pin sticking out of a wall): the top view is a vertical line of true length and the front view is the point b′(a′).

A line is inclined to one plane and parallel to the other. Which view shows the true length?

The view on the plane it is parallel to. Tilt a line θ to the HP but keep it parallel to the VP, and the front view a′b′ shows the true length at the true angle θ, while the top view ab lies parallel to XY and shortens to L cos θ. A 60 mm line at 35° has a top view of 49.1 mm. Swap the planes for a line inclined φ to the VP and parallel to the HP: ab shows the true length at φ and a′b′ is parallel to XY, L cos φ long.

Lines parallel, perpendicular and inclined to one reference plane: which view shows the true length: interactive loads as you scroll

What changes when the line lies in a reference plane, and what are end projectors?

A line lying in the HP has every point at zero height, so its front view falls on XY; a line lying in the VP has its top view on XY. A line in both planes lies on XY itself and both views coincide with it. End projectors are the vertical projectors through the two ends. For a line parallel to the VP, the distance between them equals the top-view length, so a 50 mm line at 30° to the HP has its end projectors 43.3 mm apart.

Predict, then check

A 60 mm rod is inclined at 35° to the HP and parallel to the VP. Its top view is

Worked examples

A rod inclined to the HP · Line PQ 65 mm long, P 12 mm above the HP and 18 mm in front of the VP, PQ inclined at 40° to the HP and parallel to the VP
  1. Draw XY. Mark p′ 12 mm above XY and p 18 mm below it on one projector
  2. From p′ draw p′q′ 65 mm long at 40° to XY: this is the true length
  3. q′ is 12 + 65 sin 40° = 53.78 mm above XY
  4. Project q down to the horizontal through p (the line is parallel to the VP, so every point is 18 mm in front)
  5. Top view pq = 65 cos 40° = 49.79 mm, parallel to XY

Answer: Front view 65 mm at 40°, top view 49.8 mm parallel to XY, end projectors 49.8 mm apart, Q 53.8 mm above the HP

Inclination from the top view · A line 75 mm long is parallel to the VP with one end on the HP; its top view measures 54 mm
  1. Draw the top view, 54 mm parallel to XY, and erect projectors at both ends
  2. The end on the HP has its front view on XY. With that point as centre and radius 75 mm, cut the other projector
  3. Rise = √(75² − 54²) = 52.05 mm
  4. θ = cos⁻¹(54/75) = 43.95°

Answer: θ = 43.9°; the upper end is 52.0 mm above the HP

A flag mast on a 1:100 site drawing · A 6 m vertical flag mast stands on the ground 2.5 m in front of a building wall (illustrative); scale 1:100
  1. The mast is perpendicular to the HP and parallel to the VP
  2. Front view: a vertical line 6000/100 = 60 mm long, starting on XY
  3. Top view: a point 25 mm below XY, labelled b(a) because the top end hides the foot

Answer: Front view 60 mm, true length; top view a single point 25 mm below XY

Chapter 10

Lines inclined to both planes: true length and true inclinations by the rotating-line method

Which syllabus covers thisAU GE3251 Unit IIVTU BCEDK103 Module 1SPPU 102012 Unit IVMU FEC204 Module 2KTU GMEST103 Module 1

Why does neither view of an oblique line show its true length or true angles?

Each view keeps only two of the three dimensions. The front view drops the depth change, so a′b′ = L cos φ; the top view drops the height change, so ab = L cos θ. Both are shorter than L. The angles on paper are steeper than the true ones: α ≥ θ and β ≥ φ. A 72 mm line at θ = 30° and φ = 40° shows a′b′ = 55.2 mm at α = 40.7° and ab = 62.4 mm at β = 47.9°.

How does the rotating-line method recover the true length and the true angles from the two views?

Swing the top view ab about a until it lies parallel to XY, at b1. Now the line is, for the moment, parallel to the VP, so project b1 up to the horizontal locus of b′: a′b1′ is the true length and its angle with XY is θ. Do the same with the front view: swing a′b′ about a′ parallel to XY, project down to the locus of b, and ab2 is the true length at φ. The trapezoid method gets the same length by setting off the heights of a′ and b′ at right angles to ab and joining their ends.

Line inclined to both planes: true length and true inclinations by the rotating-line method: interactive loads as you scroll

How are the views drawn when the true length, θ and φ are given?

Run the method backwards. First pretend the line is parallel to the VP: draw a′b1′ at θ, which gives the top-view length and the height of b′ (its locus line). Then pretend it is parallel to the HP: draw ab2 at φ, which gives the front-view length and the locus of b. Swing the top-view length about a to the locus of b, and the front-view length about a′ to the locus of b′. If b′ and b land on one vertical projector the drawing is right: for 72 mm, 30° and 40° both land 41.8 mm from A's projector.

Why can θ + φ never exceed 90°?

The height change L sin θ and the depth change L sin φ are two perpendicular parts of the same line, so sin²θ + sin²φ cannot exceed 1, which means θ + φ ≤ 90°. At exactly 90° nothing is left along XY: the line lies in a profile plane, both views are vertical and on one projector, and a side view is needed to see the true length. A line at 50° to the HP can make at most 40° with the VP.

Where does this show up outside the drawing sheet?

Any straight member between two points at different heights and depths: a ladder leaning on a wall and a parapet, a stay cable, a pipe or duct between two floors, a conveyor. Plans and elevations give each view only, so the true length (the material to cut) and the true slope come from this construction. A pipe from 0.5 m to 3.5 m above the floor, 1.2 m and 2.8 m from the back wall and 4 m apart along it, is 5.25 m long and rises at 34.9° (illustrative).

Predict, then check

The front view of a line inclined to both planes makes 40° with XY. The line's true inclination θ to the HP is

Worked examples

Views from the true length and angles · Line AB 72 mm long, A 18 mm above the HP and 24 mm in front of the VP, θ = 30°, φ = 40°
  1. Mark a′ 18 mm above XY and a 24 mm below it
  2. Draw a′b1′ 72 mm at 30°: top-view length = 72 cos 30° = 62.35 mm; locus of b′ at 18 + 36 = 54 mm above XY
  3. Draw ab2 72 mm at 40°: front-view length = 72 cos 40° = 55.16 mm; locus of b at 24 + 72 sin 40° = 70.28 mm below XY
  4. Swing 62.35 mm about a to the locus of b: b is √(62.35² − 46.28²) = 41.79 mm to the right
  5. Swing 55.16 mm about a′ to the locus of b′: b′ is √(55.16² − 36²) = 41.79 mm to the right, on the same projector as b
  6. Apparent angles: α = tan⁻¹(36/41.79) = 40.7°, β = tan⁻¹(46.28/41.79) = 47.9°

Answer: a′b′ = 55.2 mm at 40.7°, ab = 62.4 mm at 47.9°, end projectors 41.8 mm apart

True length from given views · a′ 15 mm and b′ 50 mm above XY, a 20 mm and b 45 mm below XY, end projectors 40 mm apart
  1. Top view ab = √(40² + 25²) = 47.17 mm, front view a′b′ = √(40² + 35²) = 53.15 mm
  2. Swing ab about a parallel to XY to b1, project up to the locus of b′ (50 mm): a′b1′ = √(47.17² + 35²) = 58.74 mm
  3. θ = tan⁻¹(35/47.17) = 36.58°
  4. Swing a′b′ about a′ parallel to XY to b2′, project down to the locus of b (45 mm): ab2 = √(53.15² + 25²) = 58.74 mm
  5. φ = tan⁻¹(25/53.15) = 25.19°; check: α = 41.2° > θ and β = 32.0° > φ

Answer: TL = 58.7 mm (both constructions agree), θ = 36.6°, φ = 25.2°

A pipe between two points in a room · Pipe from P (0.5 m above the floor, 1.2 m from the back wall) to Q (3.5 m above the floor, 2.8 m from the wall, 4.0 m further along it); drawn at 1:50 (illustrative)
  1. Elevation (FV) length on paper: √(4² + 3²) m = 5 m → 100 mm
  2. Plan (TV) length on paper: √(4² + 1.6²) m → 86.2 mm
  3. Rotating line: true length = √(4² + 3² + 1.6²) = 5.250 m, 105.0 mm on the sheet
  4. θ = sin⁻¹(3/5.250) = 34.85°, φ = sin⁻¹(1.6/5.250) = 17.74°

Answer: Cut 5.25 m of pipe; it rises at 34.9° to the floor and runs at 17.7° to the wall

Chapter 11

Traces of a line and the auxiliary-plane method

Which syllabus covers thisAU GE3251 Unit IIVTU not in syllabusSPPU 102012 Unit IVMU FEC204 Module 2KTU GMEST103 Module 1

What are the traces of a line?

A trace is the point where the line, extended if needed, meets a reference plane. The horizontal trace HT is where it meets the HP, so its height is zero and its front view h′ lies on XY. The vertical trace VT is where it meets the VP, so its distance in front is zero and its top view v lies on XY. A line parallel to a plane never meets it: a line parallel to the HP has no HT, and one parallel to both planes has no traces at all.

How are the HT and VT found on the drawing?

For the HT, extend the front view a′b′ until it meets XY at h′, then drop a projector from h′ to the top view ab, extended: that point is the HT. For the VT, extend ab to meet XY at v and raise a projector to a′b′, extended: that point is the VT. A trace can land behind the VP or below the HP. A 50 mm line from A (10 mm up, 35 mm out) at θ 40° and φ 30° has its HT 27.2 mm in front of the VP and its VT 35.0 mm below the HP.

Traces of a line and the auxiliary-plane method for true length: interactive loads as you scroll

What is the auxiliary-plane method, and how does it give the true length?

Instead of turning the line, turn the viewer. Draw a new reference line X1Y1 parallel to the top view ab. That is a new vertical plane parallel to the line, so a view on it shows the true length. Draw projectors from a and b at right angles to X1Y1 and mark a1′ and b1′ beyond it at the heights of a′ and b′ above XY. a1′b1′ is the true length and its angle with X1Y1 is θ. An X1Y1 parallel to a′b′, with depths transferred, gives the true length and φ. Mumbai University leaves traces out but uses this method.

Why would anyone need a trace in practice?

A trace is where a straight member pierces a floor or a wall: the spot to core a hole for a pipe, a duct or a cable, or the anchor point of a stay. In the worked example a pipe running towards a wall would meet the wall 0.6 m above the floor and 1.5 m to the left of its lower end, before it could reach floor level. Traces of planes, which are lines rather than points, are used the same way for sloping roofs and chutes.

Predict, then check

A line is parallel to the HP and inclined to the VP. Its traces are

Worked examples

Traces from the two views · a′ 20 mm and b′ 45 mm above XY, a 10 mm and b 40 mm below XY, end projectors 50 mm apart
  1. Extend a′b′ to XY: it drops 25 mm per 50 mm, so it meets XY 40 mm to the left of a′'s projector at h′
  2. Project h′ down to ab extended: ab moves 30 mm per 50 mm, so at 40 mm to the left it is 10 − 0.6 × 40 = −14 mm, i.e. 14 mm above XY
  3. The HT is therefore 14 mm behind the VP
  4. Extend ab to XY: it meets XY 16.67 mm to the left at v; project up to a′b′ extended: 20 − 0.5 × 16.67 = 11.67 mm above XY

Answer: HT 14 mm behind the VP, 40 mm left of A; VT 11.67 mm above the HP, 16.67 mm left of A

True length by auxiliary planes · The same line as the previous example
  1. Top view ab = √(50² + 30²) = 58.31 mm. Draw X1Y1 parallel to ab, any distance away
  2. Projectors from a and b at right angles to X1Y1; mark a1′ 20 mm and b1′ 45 mm beyond it (heights of a′ and b′)
  3. a1′b1′ = √(58.31² + 25²) = 63.44 mm, at θ = tan⁻¹(25/58.31) = 23.21° to X1Y1
  4. Front view a′b′ = √(50² + 25²) = 55.90 mm. X2Y2 parallel to a′b′, depths 10 and 40 mm transferred: TL = √(55.90² + 30²) = 63.44 mm at φ = 28.22°

Answer: TL = 63.4 mm both ways, θ = 23.2°, φ = 28.2°

Where a pipe meets the wall · A straight pipe passes through P (1.5 m above the floor, 0.6 m from the wall) and Q (2.7 m up, 1.4 m from the wall, 2.0 m to the right); extend it back towards the wall; drawing at 1:50 (illustrative)
  1. Plan: the pipe comes 0.8 m nearer the wall for every 2.0 m to the left; it reaches the wall (v on XY) 0.6/0.8 × 2.0 = 1.5 m to the left of P
  2. Elevation: over those 1.5 m it drops 1.2 × 0.75 = 0.9 m, so the VT is 0.6 m above the floor
  3. On the sheet: 30 mm left of p′ and 12 mm above XY
  4. The HT would be 2.5 m to the left and 0.4 m behind the wall face: the pipe meets the wall first

Answer: Core the wall 0.6 m above the floor, 1.5 m to the left of P

Chapter 12

Projection of planes: polygons and circles inclined to both reference planes

Which syllabus covers thisAU GE3251 Unit IIVTU BCEDK103 Module 1SPPU 102012 Unit IVMU FEC204 Module 2KTU not in syllabus

In what positions can a plane lamina sit, and what are the traces of a plane?

A plane can be parallel to the HP (top view is the true shape, front view a line), parallel to the VP (front view true, top view a line), perpendicular to both (a profile plane: both views are lines), inclined to one and perpendicular to the other (one view is a line at the true angle, the other is foreshortened), or inclined to both (no view is true). A plane meets the HP and VP in lines, not points: its horizontal and vertical traces.

How is a lamina inclined to both planes drawn in three stages?

Stage 1: lay it flat on the HP with the resting edge perpendicular to the VP; the top view is the true shape and the front view a line on XY. Stage 2: tilt it about that edge to θ; the front view becomes a line at θ, the same length as before, and the top view narrows, found with projectors and horizontal locus lines. Stage 3: redraw that top view turned until the resting edge makes φ with XY, then project up to the heights of stage 2. Nothing is guessed: every point comes from a projector meeting a locus line.

Projection of a plane inclined to both HP and VP in three stages by the change-of-position method: interactive loads as you scroll

How much smaller is the top view of a tilted lamina?

Tilting about a horizontal edge squeezes every distance across that edge by cos θ and leaves distances along it unchanged, so the top view's area is the true area times cos θ. Turning the lamina about a vertical axis in stage 3 does not change the top view's area at all. A regular hexagon of 30 mm side has a true area of 2,338.3 mm²; tilted 60° to the HP its top view covers 1,169.1 mm², exactly half.

Why does a tilted circle project as an ellipse, and how big is it?

The diameter along the hinge stays horizontal and keeps its full length D: that is the major axis. The diameter at right angles to it tilts by θ and shrinks to D cos θ: the minor axis. Every chord in between shrinks by the same factor across the hinge, which is exactly what turns a circle into an ellipse. A 60 mm disc at 45° to the HP has a top view of 60 × 42.4 mm. On paper, 12 points on the circle are projected and joined freehand or with a French curve.

The resting edge makes φ with the VP. Is that the angle of the lamina with the VP?

No. The resting edge lies in the HP, so its top view shows its true angle φ with the VP. The surface itself makes a larger angle with the VP, cos⁻¹(sin θ cos φ): a pentagon at θ = 40° whose resting edge is at 35° to the VP has its surface at 58.2° to the VP. Problems also give an apparent angle: the angle a line in the lamina, not lying in the HP (say a diameter through the resting point), makes with XY in the top view, which differs from its true angle.

Predict, then check

A hexagonal plate is tilted to 60° with the HP about one of its edges. Compared with its true area, the top view covers

Worked examples

Pentagonal plate inclined to both planes · Regular pentagon of 32 mm side resting on the HP on one edge, surface at 40° to the HP, resting edge at 35° to the VP
  1. Stage 1: true shape in the top view with the resting edge perpendicular to XY; width across the edge = R(1 + cos 36°) = 49.24 mm, area = 1,761.8 mm²
  2. Stage 2: front view a line 49.24 mm long at 40°; highest corner 31.65 mm above the HP; top view width 49.24 cos 40° = 37.72 mm
  3. Stage 3: redraw the stage 2 top view with the resting edge at 35° to XY; project up to the heights of stage 2
  4. Top view area = 1,761.8 × cos 40° = 1,349.6 mm²; surface to the VP = cos⁻¹(sin 40° cos 35°) = 58.2°

Answer: Highest corner 31.7 mm above the HP, top view area 1,350 mm², surface at 58.2° to the VP

A manhole cover leaning on its rim · A 600 mm circular cover drawn at 1:10 (D = 60 mm on paper) rests on the HP on a point of its rim, surface at 30° to the HP, the horizontal diameter at 45° to the VP (illustrative)
  1. Divide the circle into 12 parts; stage 1 top view is the true circle
  2. Stage 2: front view a line 60 mm long at 30°; top point 30 mm above XY; top view an ellipse 60 × 60 cos 30° = 51.96 mm
  3. Stage 3: turn the ellipse until its major axis makes 45° with XY, project the 12 points up to the stage 2 heights
  4. The front view is also an ellipse: major axis 60 mm, minor axis 60 sin 30° cos 45° = 21.21 mm

Answer: Top view ellipse 60 × 52.0 mm, front view ellipse 60 × 21.2 mm, top 30 mm above the HP

Finding θ from the top view · A square plate of 40 mm side rests on one edge on the HP; its top view measures 28 mm across the resting edge; the resting edge is at 30° to the VP
  1. Across the hinge the top view is s cos θ, so cos θ = 28/40 and θ = 45.57°
  2. Opposite edge height = 40 sin θ = 28.57 mm
  3. Top view area = 40 × 28 = 1,120 mm² (the stage 3 turn does not change it)
  4. Surface to the VP = cos⁻¹(sin 45.57° × cos 30°) = 51.80°

Answer: θ = 45.6°, opposite edge 28.6 mm above the HP, surface at 51.8° to the VP

Chapter 13

Projection of solids in simple positions: prisms, pyramids, cylinders and cones

Which syllabus covers thisAU GE3251 Unit IIIVTU BCEDK103 Module 2SPPU 102012 Unit IVMU FEC204 Module 3KTU GMEST103 Module 2

Which solids does engineering graphics draw?

Two families. Polyhedra have only flat faces: the five regular ones (tetrahedron, cube, octahedron, dodecahedron, icosahedron with 4, 6, 8, 12 and 20 faces), and the prisms and pyramids named after their base: triangular, square, pentagonal, hexagonal. Solids of revolution come from spinning a shape about an axis: the cylinder, the cone and the sphere. Every convex polyhedron obeys Euler's count V − E + F = 2; a pentagonal prism has 10 corners, 15 edges and 7 faces. Cut a pyramid or cone parallel to its base and you get a frustum; cut it at a slant and it is a truncated solid.

What are the axis, the generators and the slant height?

The axis joins the centre of the base to the apex (pyramid, cone) or to the centre of the top face (prism, cylinder). In a right solid it is perpendicular to the base. Lateral faces meet in lateral edges; on a cylinder or cone the straight lines on the curved surface are generators. Two lengths get mixed up on a pyramid: the slant height of a face (apex to the middle of a base edge) and the slant edge (apex to a corner). For a square pyramid of side 40 mm and axis 60 mm they are 63.25 and 66.33 mm.

What is a simple position, and which view shows the true shape?

A solid is in a simple position when its axis is perpendicular to one reference plane. Axis perpendicular to the HP (standing on its base): the top view is the true shape of the base, and the front and side views are rectangles for prisms and cylinders, triangles for pyramids and cones. Axis perpendicular to the VP: the front view shows the true base. Axis parallel to both: the side view does. Start from the view that shows the base, then project the others from it, keeping the height in the front view and the depth in the top view.

Front, top and side views of prisms, pyramids, cylinders and cones, with hidden edges dashed: interactive loads as you scroll

When does a front view need dashed lines?

An edge at the back is drawn dashed only if no visible line covers it. A pentagonal prism of side 30 mm standing with a face parallel to the VP shows 4 visible vertical lines in the front view and 1 dashed one: the back edge sits on the axis, where nothing in front hides it. Turn it so a lateral edge faces you and the view has 3 visible and 2 dashed lines. In a hexagonal prism every back edge lies exactly behind a front one, so the view has none. Hidden edges are drawn as dashed narrow lines (SP 46).

Predict, then check

A pentagonal prism stands on its base with one lateral edge nearest the observer. How many dashed lines does its front view have?

Worked examples

Hexagonal prism standing on its base · Hexagonal prism, base side 30 mm, axis 70 mm, base on the HP with two base edges parallel to the VP, axis 40 mm in front of the VP
  1. Top view first: a regular hexagon of side 30 mm (true shape), centre 40 mm below XY; across corners 60 mm along XY, across flats 30√3 = 51.96 mm
  2. The two edges parallel to the VP are 14.02 mm and 65.98 mm in front of it
  3. Project the corners up: front view lines at 30 and 15 mm either side of the axis, 70 mm tall; the back edges fall exactly behind the front ones, so no dashed lines
  4. Volume = (3√3/2) × 30² × 70 = 1,63,679 mm³; lateral area = 6 × 30 × 70 = 12,600 mm²

Answer: Front view 60 × 70 mm with four vertical lines and none dashed; volume 163.7 cm³, total area 172.8 cm²

Cone standing on its base · Cone, base diameter 50 mm, axis 60 mm, base on the HP, axis 35 mm in front of the VP
  1. Top view: a circle of 50 mm diameter, centre 35 mm below XY, with two centre lines
  2. Front view: a triangle with a 50 mm base on XY and the apex 60 mm above it; the outline generators are the true slant height √(25² + 60²) = 65 mm
  3. Each outline generator makes atan(60/25) = 67.38° with the HP
  4. Volume = π × 25² × 60/3 = 39,270 mm³, curved area = π × 25 × 65 = 5,105 mm²

Answer: Slant height 65 mm at 67.4° to XY; volume 39.3 cm³, total area 70.7 cm²

Pentagonal pyramid with a base edge parallel to the VP · Pentagonal pyramid, base side 30 mm, axis 55 mm, base on the HP, one base edge parallel to the VP and nearer the observer
  1. Circumradius R = 30/(2 sin 36°) = 25.52 mm, inradius r = 30/(2 tan 36°) = 20.65 mm
  2. Top view: the pentagon with its front edge parallel to XY; the apex projects to the centre and the five slant edges are visible
  3. Front view width = 2R cos 18° = 48.54 mm; the slant edge to the back corner lies on the axis and is dashed
  4. Slant edge = √(55² + R²) = 60.63 mm, face slant height = √(55² + r²) = 58.75 mm, lateral area = 5 × 30 × 58.75/2 = 4,406 mm²

Answer: Front view 48.5 mm wide with one dashed line; slant edge 60.6 mm, lateral area 44.1 cm²

Chapter 14

Solids with the axis inclined to one or both reference planes

Which syllabus covers thisAU GE3251 Unit IIIVTU BCEDK103 Module 2SPPU not in syllabusMU FEC204 Module 3KTU GMEST103 Module 2

Why draw a tilted solid in stages?

With the axis tilted, no view shows the base in true shape, so there is nothing to start from. So start in a simple position (stage 1: axis vertical, the top view is the true base), then tilt (stage 2). Turning the solid about an edge perpendicular to the VP only rotates the front view: copy it at the new angle. Every corner keeps its distance from the VP, so each top-view point lies on the projector from the new front view at its old depth. A 60 mm axis at 40° to the HP shows 45.96 mm long in the top view.

What changes when the solid rests on an edge, a corner or a generator?

Resting on a base edge or a base corner, the solid turns about that edge or corner and the axis angle θ is yours to choose; the resting element must stay on XY in the front view. Resting on a lateral edge, a slant edge or a generator, the shape decides: a prism or cylinder lying on a side edge has its axis parallel to the HP, and a cone of 50 mm diameter and 60 mm axis lying on a generator has its axis at atan(25/60) = 22.6° to the HP.

Solids with the axis inclined to the HP and the VP: resting on an edge or a corner: interactive loads as you scroll

How is the axis made inclined to both planes?

Add stage 3: turn the stage-2 top view about a vertical line until the axis makes the required true angle φ with the VP. The heights do not change, so the new front view is found from the old heights and the new top view. The top view of the axis makes an apparent angle β with XY, larger than φ: for θ = 40° and φ = 30°, β = 40.7°. θ + φ cannot exceed 90°. Mumbai University also accepts the auxiliary plane method: draw a new reference line instead of turning the solid; the views come out the same.

Which edges are hidden once the solid tilts?

The outline of every view is visible. Inside it, an edge is visible if a face next to it faces the observer: in the front view, check the top view to see which corners are nearer the observer (further below XY); in the top view, check the front view to see which are higher. The rest are dashed. A circular base no longer shows as a circle: with the axis at θ to the HP it becomes an ellipse in the top view, major axis D and minor axis D sin θ, 28.7 mm for D = 50 mm at 35°.

Predict, then check

A cone (base 50 mm, axis 60 mm) lies on the HP on one of its generators, axis parallel to the VP. What angle does its axis make with the HP?

Worked examples

Pyramid resting on a base edge · Pentagonal pyramid, base side 30 mm, axis 60 mm, resting on the HP on a base edge perpendicular to the VP, axis 40° to the HP and parallel to the VP
  1. Stage 1: pentagon in the top view with the resting edge perpendicular to XY; inradius 20.65 mm, circumradius 25.52 mm
  2. Stage 2: redraw the front view turned about the resting edge until the axis is at 40° (the base at 50° to the HP)
  3. Base centre height = r sin 50° = 15.82 mm; apex height = 15.82 + 60 sin 40° = 54.38 mm
  4. Highest base corner = (r + R) sin 50° = 35.36 mm
  5. Top view from the new front view and the stage-1 depths; the axis is 45.96 mm long in it

Answer: Apex 54.4 mm above the HP, top corner 35.4 mm, axis 46.0 mm long in the top view

Cylinder resting on its base rim · Cylinder, diameter 50 mm, axis 70 mm, resting on a point of its base circle on the HP, axis 35° to the HP and parallel to the VP
  1. Stage 1: circle in the top view, rectangle 50 × 70 mm in the front view
  2. Stage 2: turn the rectangle about its lower right corner until the axis is at 35°
  3. Highest point (far side of the top face) = 50 sin 55° + 70 cos 55° = 81.11 mm
  4. Top view: both end circles become ellipses with major axis 50 mm and minor axis 50 sin 35° = 28.68 mm
  5. Overall length of the top view along XY = 70 cos 35° + 50 sin 35° = 86.02 mm

Answer: Top 81.1 mm above the HP; top view 86.0 mm long with ellipses of minor axis 28.7 mm

Inclined to both planes · The pyramid of the first example, now with its axis at 30° to the VP as well (θ = 40°, φ = 30°)
  1. Check the limit: θ + φ = 70° ≤ 90°, so the position exists
  2. Stage 3: turn the stage-2 top view so its axis makes β with XY, sin β = sin 30°/cos 40°, β = 40.75°
  3. The top view keeps its shape; the axis there is still 45.96 mm
  4. Project the front view from the heights of stage 2: the axis shows 51.96 mm long (60 cos 30°) at an apparent 47.9° to XY

Answer: β = 40.7°; front view of the axis 52.0 mm at 47.9° to XY

Chapter 15

Sections of solids and the true shape of the section

Which syllabus covers thisAU GE3251 Unit IVVTU not in syllabusSPPU not in syllabusMU FEC204 Module 4KTU GMEST103 Module 3

What are the section plane, the section and the sectional view?

Imagine slicing the solid with a flat plane. The plane is the section plane; the flat face it leaves is the section. Remove the part between the plane and the observer and draw what is left: that is the sectional view, with the section hatched in thin lines, preferably at 45° to the main outlines (SP 46). The plane is shown edge-on in the other view by a long-dashed dotted thin line, made thick at its ends. Here the plane is perpendicular to one reference plane, so it shows as a line in that view.

Which plane positions give the true shape directly, and which need more work?

A plane parallel to the HP cuts a shape that the top view shows true. A plane perpendicular to the VP and tilted at α to the HP shows as a line in the front view, and the top view shrinks the section by cos α along XY: a hexagonal prism of side 30 mm cut at 35° has a 2,854 mm² section but a 2,338 mm² top view. A plane perpendicular to the HP and tilted to the VP is the same story with the views swapped.

How is the true shape of the section drawn?

Use an auxiliary plane parallel to the section plane. Draw a new reference line X1Y1 parallel to the plane's trace in the front view. From each point where the trace cuts an edge, draw a projector perpendicular to X1Y1, and mark off the point's distance in front of the VP, measured from XY in the top view. Join the points: that is the true shape. A cylinder of 60 mm diameter cut at 30° gives an ellipse with axes 60 and 60/cos 30° = 69.28 mm. The reverse problem works backwards: a 50 mm cylinder whose true shape is a 70 mm long ellipse is cut at acos(50/70) = 44.4° (KTU leaves this out).

Why are the ellipse, parabola and hyperbola called conic sections?

They are the sections of a right circular cone. Compare the plane's angle α with the angle γ of the generators to the base: 69.4° for a cone of 60 mm diameter and 80 mm axis. α = 0 gives a circle; α below γ, an ellipse; α equal to γ (parallel to a generator), a parabola; α above γ, a hyperbola; a plane through the apex and steeper than the generators, a triangle. The eccentricity of chapter 3 is e = sin α / sin γ: 0.755 at α = 45°, exactly 1 for the parabola.

Section of solids: the cutting plane, the sectional top view and the true shape of the section: interactive loads as you scroll
Predict, then check

A cone with generators at 69.4° to its base is cut through the middle of its axis by a plane at 75° to the HP, perpendicular to the VP. The section is

Worked examples

Hexagonal prism cut by an inclined plane · Hexagonal prism, base side 30 mm, axis 80 mm vertical, two base edges parallel to the VP; section plane perpendicular to the VP at 35° to the HP through the middle of the axis
  1. In the front view the trace runs from 18.99 mm above XY at the left edge to 61.01 mm at the right; it cuts only the six lateral edges
  2. Sectional top view: the hexagon of the base, now hatched, because the cut face lies over the whole base
  3. True shape: X1Y1 parallel to the trace; the length along it is 60/cos 35° = 73.25 mm, the width across flats stays 30√3 = 51.96 mm
  4. Area = base area / cos 35° = 2,338.3/0.8192 = 2,854.5 mm²

Answer: An elongated hexagon 73.2 mm long and 52.0 mm wide, area 28.5 cm² against 23.4 cm² in the top view

Ellipse from a cone · Cone, base 60 mm, axis 80 mm vertical; section plane perpendicular to the VP at 45° to the HP through the axis 40 mm above the base
  1. Generator angle γ = atan(80/30) = 69.44° > 45°, and 40 mm > 30 tan 45° = 30 mm: the plane misses the base, so the section is a full ellipse
  2. The trace meets the outline generators at x = −24.00 and 10.91 mm: major axis = (10.91 + 24.00)/cos 45° = 49.37 mm
  3. At its midpoint (x = −6.55 mm, height 33.45 mm) the cone's circle has radius 17.45 mm, so the minor axis = 2√(17.45² − 6.55²) = 32.36 mm
  4. Area = π × 24.68 × 16.18 = 1,254.8 mm²; e = sin 45°/sin 69.44° = 0.7552

Answer: Ellipse 49.4 × 32.4 mm, area 12.5 cm², eccentricity 0.755

Parabola from the same cone · The same cone; section plane parallel to the left outline generator (at γ to the HP) through the axis 40 mm above the base
  1. The plane meets the base at x = −40/tan γ = −15 mm: a chord of 2√(30² − 15²) = 51.96 mm
  2. It meets the right generator at (7.5, 60) mm: the vertex of the parabola
  3. Along the plane, vertex to chord = √(22.5² + 60²) = 64.08 mm
  4. Area of a parabolic segment = ⅔ × chord × height = ⅔ × 51.96 × 64.08 = 2,219.8 mm²

Answer: A parabola 64.1 mm high on a 52.0 mm base chord, area 22.2 cm²

Chapter 16

Development of lateral surfaces: parallel-line and radial-line methods, and truncated solids

Which syllabus covers thisAU GE3251 Unit IVVTU BCEDK103 Module 4SPPU 102012 Unit VIMU not in syllabusKTU GMEST103 Module 3

What is a development, and where is it used?

A development is the flat pattern that folds or rolls into the surface of a solid, with every line at its true length. Sheet-metal work runs on it: ducts, hoppers, chimneys, funnels, trays and boxes are marked out flat, cut, bent and joined at a seam. Prisms, pyramids, cylinders and cones can be developed exactly because they unroll without stretching. A sphere cannot; it is made from approximate pieces called gores. Bend lines on a blank are drawn as thin continuous lines (SP 46).

How does the parallel-line method work?

Prisms and cylinders have parallel lateral edges or generators, so their surface opens into a strip. Draw a stretch-out line equal to the base perimeter, divide it into the base edges (or, for a cylinder, 12 equal parts of πD), and erect the edges or generators at their true lengths, which the front view shows directly. A cylinder of 48 mm diameter and 64 mm height develops into a 150.8 × 64 mm rectangle. The seam usually goes on the shortest line, which keeps the joint short.

How does the radial-line method work?

Pyramids and cones have all their lateral lines meeting at the apex, so their surface opens into a fan. For a cone, swing an arc of radius equal to the slant height L and make the sector angle 360° × R/L, so the arc equals the base circumference: a cone of 54 mm diameter and 64 mm axis has L = 69.46 mm and a 139.9° sector. For a pyramid, find the true length of a slant edge first (70.68 mm for a hexagonal pyramid of side 30 mm and axis 64 mm), then lay out the triangles: 147.0° in all.

How do you develop a truncated solid?

Develop the whole surface first, numbering the edges or generators. In the front view, mark where the cutting plane crosses each one. Carry each cut point to the same line in the development at its true distance from the base. For a prism or cylinder the heights go straight across, because the generators are true length in the front view. For a pyramid or cone, slide the point horizontally onto the outline generator, which is true length, and measure from the apex. Join the points: straight between edges on flat faces, a smooth curve on a curved surface.

Development of lateral surfaces: parallel-line and radial-line methods for prisms, cylinders, pyramids and cones: interactive loads as you scroll

What is the shortest path between two points on a cylinder?

Unroll the surface and draw a straight line: rolled back up, it is the shortest path (a piece of helix). An ant going from the bottom rim of a 48 mm by 64 mm can to the opposite point on the top rim walks across half the circumference (75.4 mm) and up 64 mm: √(75.4² + 64²) = 98.9 mm, at 40.3° to the base. Going straight up and across the lid would take 112 mm.

Predict, then check

A cone keeps its 60 mm base but its axis goes from 40 mm to 80 mm. Its development sector angle

Worked examples

Truncated hexagonal prism · Hexagonal prism, base side 24 mm, axis 64 mm, corners on the left and right; cut by a plane perpendicular to the VP at 30° to the HP through the axis 38.4 mm above the base, part above removed
  1. Stretch-out line 6 × 24 = 144 mm, seam on the shortest edge (left corner)
  2. Kept edge heights from the front view (38.4 + x tan 30°): 24.54, 31.47, 45.33, 52.26, 45.33, 31.47, 24.54 mm
  3. Carry each height across to its fold line and join the tops with straight lines (each face is flat)
  4. Area = sum of six trapezoids = 5,529.6 mm²; cut edge = sum of √(24² + Δh²) = 155.3 mm, the perimeter of the section

Answer: A 144 mm strip with a peaked top edge from 24.5 to 52.3 mm, area 55.3 cm², cut edge 155.3 mm

Cone and hopper (frustum) · Cone, base 60 mm, axis 80 mm; then the same cone cut parallel to the base 50 mm up, as a hopper (illustrative)
  1. Slant height L = √(30² + 80²) = 85.44 mm; sector angle = 360 × 30/85.44 = 126.4°
  2. Full development area = πRL = 8,052.5 mm²
  3. Removed top cone: radius 30 × 30/80 = 11.25 mm, slant 32.04 mm: arc of radius 32.04 mm on the same 126.4° sector
  4. Hopper pattern: the ring between radii 32.04 and 85.44 mm, area π(30 × 85.44 − 11.25 × 32.04) = 6,920 mm²

Answer: A 126.4° ring from 32.0 to 85.4 mm radius, area 69.2 cm²

Shortest path on a cylinder · Cylinder, diameter 48 mm, height 64 mm; from a point on the bottom rim to the diametrically opposite point on the top rim
  1. Develop: a rectangle 150.8 × 64 mm; the two points are half the stretch-out apart, 75.40 mm
  2. Straight line on the development: √(75.40² + 64²) = 98.90 mm
  3. It climbs at atan(64/75.40) = 40.33° to the base, so on the cylinder it is half a turn of a helix
  4. Up the side and across the top: 64 + 48 = 112 mm, longer by 13.1 mm

Answer: 98.9 mm along half a helix turn, against 112 mm by the obvious route

Chapter 17

Development in practice: triangulation, transition pieces, funnels and trays

Which syllabus covers thisAU not in syllabusVTU BCEDK103 Module 4SPPU 102012 Unit VIMU not in syllabusKTU not in syllabus

What is triangulation, and when do you need it instead of the parallel-line or radial-line method?

Parallel lines unroll prisms and cylinders, radial lines unroll pyramids and cones. A transition piece that joins a square duct to a round one is neither: its surface twists. Triangulation splits it into thin triangles, finds the true length of every side, and lays the triangles down one after another, each sharing a side with the last. A triangle is fixed by its three sides, so the flat pattern is right if every length is right. More divisions give a smoother edge.

How do you get all those true lengths quickly?

Use a true-length diagram. Draw one vertical line equal to the height between the two ends. Measure each line's plan length in the top view and lay it off along the base from the foot of the vertical; the hypotenuse is the true length. A line with a plan length of 80 mm and a rise of 60 mm is 100 mm long. For a square-to-round piece, one diagram serves every line, because all of them rise through the same height.

How is a square-to-round transition piece built up?

Divide the circle into 12 equal parts. Each side of the square joins the circle point facing its middle: four flat triangles. Each corner joins the three circle segments facing it: four fans, each a piece of an oblique cone. That is 16 triangles. For a 300 mm square duct and a Ø200 duct 250 mm above it, the corner lines are 295.8 mm and 276.6 mm long. The seam runs up the middle of one flat face, 255.0 mm long.

Development by triangulation: a square-to-round transition piece, a funnel and a tray: interactive loads as you scroll

How are a funnel and a tray with sloping sides developed?

A funnel is a cone frustum on a cylindrical spout. The frustum unrolls into a ring-shaped sector about the cone's apex, and the spout into a rectangle π d long. A Ø240 mouth over a Ø40 spout, 150 mm apart, gives a 199.7° sector. A tray is a base plus four trapezoids folded up. In the pattern, each side keeps its true height (58.3 mm for a 180 mm top, 120 mm base and 50 mm depth). In the workshop a lap or seam strip is added along the joints; exam drawings leave it off.

Predict, then check

On the true-length diagram, a line has a plan length of 80 mm and its ends differ in height by 60 mm. Its true length is

Worked examples

Square-to-round transition for a ventilation duct · Square duct 300 × 300 mm at the bottom, round duct Ø200 mm on the same axis 250 mm above it (illustrative); circle in 12 parts
  1. Top view: draw the 300 mm square and the Ø200 circle, divide the circle into 12 and join each corner to the three points facing it
  2. Plan lengths from a corner: to the points level with the sides 158.1 mm, to the two in between 118.4 mm
  3. True-length diagram with a 250 mm vertical: √(158.1² + 250²) = 295.8 mm and √(118.4² + 250²) = 276.6 mm
  4. Seam (middle of a flat face): √(250² + 50²) = 255.0 mm
  5. Lay out the seam, then each triangle from its three true sides: half flat face, corner fan, flat face, corner fan, half flat face
  6. Area of the 16 triangles: 2,36,300 mm² (the exact curved surface is 2,36,734 mm², 0.18% more)

Answer: Corner lines 295.8 and 276.6 mm, seam 255.0 mm, sheet area about 0.236 m² before joint allowances

Funnel for filling a drum · Mouth Ø240 mm, spout Ø40 mm, cone 150 mm high, spout 60 mm long (illustrative)
  1. Slant height of the frustum = √((120 − 20)² + 150²) = 180.3 mm
  2. Extend the generators to the apex: L1 = 120 × 180.3/100 = 216.3 mm, L2 = 20 × 180.3/100 = 36.1 mm
  3. Sector angle θ = 360° × 120/216.3 = 199.7°
  4. Check: arc L1 θ = 216.3 × 3.4853 = 754.0 mm = π × 240
  5. Spout: rectangle π × 40 = 125.7 mm by 60 mm

Answer: Annular sector of radii 216.3 and 36.1 mm and angle 199.7°, plus a 125.7 × 60 mm rectangle; area 86,830 mm²

Tray with sloping sides · Square tray: top 180 mm, base 120 mm, depth 50 mm, open top (illustrative)
  1. Each side leans out by (180 − 120)/2 = 30 mm
  2. True height of a side = √(50² + 30²) = 58.3 mm
  3. Corner edge true length = √(50² + 30² + 30²) = 65.6 mm
  4. Diagonal of a side (to triangulate it) = √(150² + 58.3²) = 160.9 mm
  5. Draw the 120 mm base and fold out each side as a trapezoid 120 / 180 mm wide and the true height deep

Answer: Four trapezoids 58.3 mm deep on a 120 mm square; pattern area 49,386 mm²

Chapter 18

Orthographic views of objects from pictorial drawings, first and third angle

Which syllabus covers thisAU GE3251 Unit IIIVTU BCEDK103 Module 3SPPU 102012 Unit IVMU FEC204 Module 5KTU GMEST103 Module 2

Which side of the object should be the front view?

The most informative one. SP 46 asks for the view that shows the shape best as the front (principal) view, generally with the part in its working, manufacturing or mounting position. Then add only the views needed to define the object without doubt, choosing them to avoid hidden lines and repeated detail. In practice: put the longest side across, the side with the most visible features facing you, and check that the other views come out with as few dashed lines as possible.

Where do the six views go in first and third angle?

Imagine six directions: front, above, left, right, below and rear. In first angle the object sits between you and the plane, so the view from above goes underneath the front view and the view from the left goes on its right. In third angle the plane sits between you and the object, so the view from above goes above and the view from the left on the left. A truncated-cone symbol in the title block says which method is used. SP 46 makes first angle the basic requirement for drawings made after 31 December 1991.

From a pictorial block to its front, top and side views in first- and third-angle projection: interactive loads as you scroll

Which sizes do the views share, and what is the 45° mitre line for?

The front and top views share the width, so they line up vertically. The front and side views share the height, so they line up horizontally. The top and side views share the depth, but one shows it vertically and the other horizontally. A 45° mitre line turns one into the other: carry each depth across from the top view, turn it at the mitre and carry it up. A 120 × 60 × 80 block gives a 120 × 60 front view, 120 × 80 top view and 80 × 60 side view.

How are hidden edges, coinciding lines and curved surfaces shown?

Visible edges are continuous wide lines, hidden edges dashed narrow lines and axes long-dashed dotted narrow lines (SP 46 Table 6.8). Where two lines fall on each other, draw the more important one: visible beats hidden, hidden beats a centre line. In an L-block of 20 mm cubes, the inside corner of the L is hidden in the side view and shows as one dashed line 60 mm long. A curved surface shows an edge line only where it ends or meets another surface; a rounded corner may be marked by a thin line that stops short of the outline.

How do you sketch the views freehand from a pictorial drawing?

Work on squared paper and get the proportions first. Count the overall width, height and depth in squares, block in the three rectangles in their places with light lines, and line up the views by eye along the grid. Then add features one at a time, carrying each across to the other views before moving on. Darken visible lines last, then dashed hidden lines and centre lines. Sizes come from the pictorial drawing; the sketch only has to keep their ratios.

Predict, then check

In a first-angle drawing, the view seen from the left of the object is placed

Worked examples

Lay out three views on the sheet · A block 120 wide, 60 high and 80 deep; drawing space 380 × 260 mm; 30 mm between views; first angle (sizes illustrative)
  1. Width needed: front view 120 + gap 30 + side view 80 = 230 mm; height needed: front view 60 + 30 + top view 80 = 170 mm
  2. Margins: left (380 − 230)/2 = 75 mm, top (260 − 170)/2 = 45 mm
  3. Front view at 75 mm from the left and 45 mm from the top
  4. Top view under it, starting 135 mm from the top; side view (from the left) to its right, starting 225 mm from the left
  5. In third angle the same space holds the top view on top and the side view on the left; the front view then starts 185 mm from the left and 155 mm from the top

Answer: A 230 × 170 mm block of views centred with 75 mm side and 45 mm top margins

Hidden line in the side view of an L-block · An L-block of 20 mm cubes: a base 4 cubes wide, 3 deep, 1 high, with an upright 1 cube wide and 3 high at its left end
  1. Front view: an L, 80 wide and 60 high
  2. Top view: an 80 × 60 rectangle with a line 20 mm from the left, where the upright ends
  3. Side view from the left: the upright fills a 60 × 60 square
  4. The top of the base (20 mm up) lies behind the upright, so its edge is hidden: one dashed line across the side view, 60 mm long

Answer: Side view: 60 × 60 square with one hidden line 60 mm long at 20 mm height

Hidden lines in the top view of a T-block · A T-block of 20 mm cubes: top bar 4 cubes wide, 3 deep, 1 high, standing on a stem 2 cubes wide and 2 high, all 3 deep
  1. Front view: a T, 80 wide and 60 high
  2. Top view: the bar covers everything, so the outline is an 80 × 60 rectangle
  3. The stem's two side faces lie under the bar: each shows as a dashed line 60 mm long, 20 mm in from each end
  4. Side view from the left: a 60 × 60 square with a visible line 40 mm up, where the bar overhangs the stem

Answer: Top view: rectangle with two hidden lines; this is why a view from below, or a section, can be clearer

Chapter 19

Sectional views of machine parts: full and half sections and hatching

Which syllabus covers thisAU not in syllabusVTU not in syllabusSPPU 102012 Unit IVMU FEC204 Module 5KTU not in syllabus

Why cut a part open on paper, and how is the cut shown?

A hollow part drawn from outside is a tangle of dashed lines. Imagine a plane slicing it, take away the part in front, and draw what is left: the inside now shows in continuous lines. The plane is drawn in the other view as a long-dashed dotted narrow line, wide at its ends and bends, with letters and arrows for the viewing direction; the view is then labelled A-A. If the position of a single plane is obvious, SP 46 lets you leave the line out.

What is the difference between a full section and a half section?

A full section cuts right through, usually along the axis. A half section suits symmetrical parts: one quarter is taken away, so one half shows the outside and the other the inside, split by the centre line. Hidden lines are normally left out of both halves. A flanged bush with a 776 mm² profile shows 1,552 mm² of hatching in full section and 776 mm² in half section.

Full and half sectional views of a machine part, with hatching and the rules for what is not sectioned: interactive loads as you scroll

What are the rules for hatching?

Hatching marks cut material only, never holes or the space beyond. SP 46 asks for continuous narrow lines, preferably at 45° to the main outline or the line of symmetry. Every cut area of one part is hatched the same way, even when it appears on both sides of a bore. Neighbouring parts get a different direction or spacing. Spacing grows with the size of the area, and a large area may be hatched only along its outline. Very thin sections may be filled black, with at least 0.7 mm between neighbouring ones.

Which parts are not hatched even when the plane passes through them?

SP 46 lists ribs, fasteners, shafts, spokes of wheels and the like: in principle they are not cut in longitudinal sections. A shaft through a pulley is drawn whole, in outside view, while the pulley around it is hatched. Hatching a solid shaft or a bolt along its length tells the reader nothing new, and a hatched rib or spoke would make a thin web look like a solid disc. Cut across their length, they are sectioned as usual.

What other kinds of section are used?

A section in two parallel planes (an offset section) catches features that do not lie in one plane. A revolved section turns a cross-section through 90° on the view itself and outlines it with continuous narrow lines. A removed section is drawn away from the view, outlined with continuous wide lines and labelled. A local section breaks out a small region with a freehand line when a full or half section is not convenient.

Predict, then check

A pulley sits on a shaft, and the cutting plane passes through the axis of both. In the full section,

Worked examples

Hatched area of a flanged bush · Flange Ø80 × 12 mm, hub Ø44 to 60 mm long overall, bore Ø24 with a Ø32 counterbore 10 mm deep (illustrative)
  1. Profile on one side of the axis: flange 12 × (40 − 12) = 336 mm², hub 48 × (22 − 12) = 480 mm², minus the counterbore 10 × (16 − 12) = 40 mm²
  2. One side: 336 + 480 − 40 = 776.0 mm²
  3. Full section: both sides are cut, 1,552 mm² of hatching, one direction throughout
  4. Half section: one side only, 776.0 mm²
  5. Bonus (Pappus): the profile's centroid is 21.05 mm from the axis, so the bush holds 2π × 21.05 × 776.0 = 1,02,642 mm³ of metal

Answer: Hatched area 1,552 mm² (full), 776.0 mm² (half); volume 1,02,642 mm³

How many hatch lines? · A cut area 40 × 12 mm hatched at 45° with lines 3 mm apart
  1. Measured across the hatch direction, the rectangle spans (40 + 12)/√2 = 36.77 mm
  2. Lines every 3 mm: 36.77/3 = 12.26, so 12 lines
  3. Their total length × spacing ≈ the area: 159 × 3 = 478 mm² against 480 mm²

Answer: 12 lines; for a bigger area, widen the spacing rather than draw hundreds of lines

Stepped pulley: outside view or section? · Three steps Ø100, Ø80 and Ø60, each 20 mm wide, bore Ø24 (illustrative); side view seen from the Ø100 end
  1. Outside front view: the steps show as visible lines; the bore is two dashed lines along its length
  2. Side view from the left: the Ø100 face hides the Ø80 and Ø60 steps behind it, so they come out as dashed circles; the Ø100 rim and the Ø24 bore are visible
  3. Full section: the bore becomes continuous lines and the dashed lines go; hatched area 2 × 1680.0 = 3,360 mm²
  4. Half section: 1,680 mm² hatched, with the outside steps still shown on the other half

Answer: A half section shows the steps and the bore with no hidden lines at all

Chapter 20

Reading drawings: missing views and visualising an object from two views

Which syllabus covers thisAU GE3251 Unit IIIVTU BCEDK103 Module 3SPPU not in syllabusMU FEC204 Module 6KTU not in syllabus

Are two views always enough to fix an object?

No. A square front view and a square top view fit a cube, but also a cylinder lying sideways and a wedge. Built from cubes on a 2 × 2 × 2 grid, 37 one-piece objects have a full square as both front and top outline. Even complete views with every visible and hidden line can be shared: for one staircase-like object on a 3 × 3 × 3 grid, 545 one-piece objects share the outlines and 2 share the complete front and top views. That is why a third view or a section is added.

Missing views: find the third view from two, and see when two views do not fix the object: interactive loads as you scroll

How do you find the third view from two given views?

Number the corners. Heights come from the front view and are carried across horizontally. Depths come from the top view, carried across and turned through the 45° mitre line, or measured with dividers from a common back edge. Each corner of the side view sits where its height and depth meet. Join the corners that are joined in the object, then decide for each line whether a nearer surface covers it: if it does, it is dashed.

What does reading by surfaces mean?

Every flat face is normal, inclined or oblique. A normal face is parallel to one principal plane: true shape in one view, a line in the other two. An inclined face is square to one plane: a line there, a foreshortened outline of the same kind in the other two. A 50 × 40 mm face tilted 30° to the HP shows as a 50 mm line, a 40 × 43.3 mm rectangle and a 40 × 25 mm rectangle. An oblique face is foreshortened in all three views but keeps its number of corners.

What routine helps with missing-view problems?

First read the overall width, height and depth and block in the missing view as a rectangle. Then take one feature at a time: find it in both given views, decide whether it is a step, slot, hole or slope, and project it. Check every line in the given views against your answer; a line with no surface to explain it means a wrong guess. Finally, sketch the object in isometric: if it is impossible to sketch, one of the views is wrong.

Predict, then check

Built from cubes on a 2 × 2 × 2 grid, how many one-piece objects have a full square as both their front and top outlines?

Worked examples

Count the objects behind two outlines · Cubes on a 2 × 2 × 2 grid; front outline and top outline both full 2 × 2 squares
  1. Every possible set of cubes: 2⁸ = 256
  2. Keep those whose front view and top view each fill all four squares
  3. 49 sets pass; 12 of them fall apart into separate pieces
  4. So 37 different solid objects give the same two outlines

Answer: 37 objects: draw the third view (or a section) to say which one you mean

Read an inclined surface · A face 50 mm long and 40 mm wide, perpendicular to the VP and inclined at 30° to the HP
  1. Front view: the face is seen edge-on, a line 50 mm long at 30°
  2. Top view: a rectangle 40 mm by 50 cos 30° = 43.3 mm
  3. Side view: a rectangle 40 mm by 50 sin 30° = 25 mm
  4. Both rectangles have four corners, like the true face: the similar-shape check

Answer: Line 50 mm, rectangles 40 × 43.3 and 40 × 25 mm

Third view of a stepped block · Puzzle 1 in the interactive, with 20 mm cubes: a 60 × 60 × 60 block stepped down towards the front and the right
  1. Overall depth from the top view: 60 mm; overall height from the front view: 60 mm, so the side view fits a 60 × 60 square
  2. Heights of the steps from the front view: 20 and 40 mm; depths from the top view: 20 and 40 mm from the back
  3. Each step that faces you from the left gives a visible line; a step hidden behind a taller part at the left end is dashed
  4. Projected this way, the side view has 12 visible and 4 hidden unit segments of 20 mm

Answer: Pick the drawing whose steps match these heights and depths; the mirror image is the classic wrong answer

Chapter 21

Isometric projection and the isometric scale

Which syllabus covers thisAU GE3251 Unit VVTU BCEDK103 Module 3SPPU 102012 Unit VMU FEC204 Module 7KTU GMEST103 Module 4

What is an isometric projection?

It is an ordinary orthographic projection, parallel projectors at right angles to the plane, of an object turned so that its three main edges are equally inclined to that plane. Turn a cube 45° about a vertical axis, then tilt its top towards you by 35.26°. The long diagonal of the cube now points straight at you, the three edges meeting at the nearest corner appear 120° apart on paper, and each of them looks shorter than it really is by the same factor, 0.8165. One view then shows the top, front and side together.

Isometric projection and the isometric scale: tilt a cube until all three edges shrink to 0.816: interactive loads as you scroll

Where does the factor 0.8165 come from, and how is an isometric scale drawn?

An edge tilted out of the paper shows shorter. For the isometric position the projected length works out to cos 45°/cos 30° = √(2/3) = 0.8165 of the true length. The isometric scale draws this directly. From a point, draw a line at 45° and mark true millimetres on it. Draw a second line at 30° from the same point. Drop vertical lines from each mark to the 30° line. The 30° line now reads isometric lengths: 100 mm true becomes 81.6 mm.

What is the difference between an isometric projection and an isometric drawing?

The isometric projection uses the isometric scale, so every edge along the three axes is drawn at 0.8165 of its true length. The isometric drawing (isometric view) skips the scale and lays off true lengths along the axes. The shape is identical; the drawing is simply 1.2247 times larger, about 22.5% bigger. Drawings are quicker and easier to measure, so most practical sketches are isometric drawings. When a question asks for an isometric projection, use the isometric scale.

Which lines can be measured in an isometric view, and what about other angles?

Only isometric lines, those parallel to one of the three axes, carry the scale. A sloping edge, such as the hypotenuse of a wedge, is a non-isometric line: its drawn length is neither its true length nor 0.8165 of it. Locate both of its ends by measuring along isometric lines (box the object, then take offsets) and join them. Right angles do not stay right angles either: a square corner appears as 60° or 120°. If the axes are foreshortened unequally, the view is dimetric (two equal) or trimetric (all three different).

Predict, then check

A 100 mm cube is drawn as an isometric projection, using the isometric scale. How long does its vertical edge measure on the paper?

Worked examples

Reading lengths off an isometric scale · True lengths 25, 40 and 70 mm; an isometric scale 0 to 100 mm
  1. Draw a horizontal line and, from its left end O, a line at 45° and a line at 30°, both above it
  2. Mark 0 to 100 mm in 10 mm steps on the 45° line. The 100 mm mark sits 70.71 mm to the right of O
  3. Drop a vertical line from each mark to the 30° line. The 100 mm projector meets it 81.65 mm from O, and 81.65/100 = 0.8165
  4. Read the three lengths on the 30° line: 25 → 20.41 mm, 40 → 32.66 mm, 70 → 57.15 mm

Answer: Isometric lengths 20.4, 32.7 and 57.2 mm (each × 0.8165)

A rectangular block: projection against drawing · Block 80 mm long, 50 mm deep, 30 mm high, resting on the ground with its edges along the isometric axes
  1. Isometric projection: edges become 80 × 0.8165 = 65.32, 50 → 40.82 and 30 → 24.49 mm
  2. Overall width on paper = (length + depth) × cos 30° = 130 × 0.8660 = 112.58 mm in the drawing, 91.92 mm in the projection
  3. Overall height on paper = height + (length + depth) × sin 30° = 30 + 65 = 95.0 mm in the drawing, 77.57 mm in the projection
  4. The ratio is the same everywhere: 112.58/91.92 = 95.0/77.57 = 1.2247

Answer: Projection 91.9 × 77.6 mm on paper, drawing 112.6 × 95.0 mm: the same shape, 1.2247 times larger

Why a sloping edge cannot be measured · A wedge whose sloping edge runs from 40 mm up at one end of a 60 mm long base down to the base at the other end
  1. True length of the slope = √(60² + 40²) = 72.11 mm
  2. In the isometric drawing, put the high end at the far corner, 40 mm up the vertical axis, and the low end 60 mm from that corner along the length axis coming towards you (drawn 30° below the horizontal), then join them
  3. The joining line measures 87.18 mm on the drawing, not 72.11 mm, and 71.18 mm in the projection, not 58.88 mm
  4. So sloping edges are always drawn by locating their ends along isometric lines, never by measuring along them

Answer: Drawn length 87.2 mm (drawing) against a true 72.1 mm: non-isometric lines carry no scale

Chapter 22

Isometric drawings of solids and their combinations

Which syllabus covers thisAU GE3251 Unit VVTU BCEDK103 Module 3SPPU 102012 Unit VMU FEC204 Module 7KTU GMEST103 Module 4

How do you draw a prism or a pyramid in isometric?

Use the box (crate) method. Draw the isometric box that just encloses the solid, using its overall length, depth and height along the three axes. Locate every corner of the base on the box's bottom face by offsets measured along isometric lines, then raise the prism's corners by the height, or find the pyramid's apex straight above the centre of its base at the full height. Join the corners and rub out the box. Hidden edges are normally left out of isometric views, so draw only what you can see.

What does a circle become, and how big is the ellipse?

A circle in any face becomes an ellipse whose major axis is at right angles to the axis of the cylinder or cone, horizontal for a circle lying flat. For a circle of diameter D the isometric projection gives an ellipse D long and D/√3 = 0.5774 D wide. The isometric drawing is 1.2247 times larger: 1.2247 D by 0.7071 D. So a 50 mm circle drawn full size along the axes comes out 61.2 × 35.4 mm.

Isometric drawings of prisms, pyramids, cylinders, cones and spheres, and the four-centre ellipse: interactive loads as you scroll

What is the four-centre method, and how accurate is it?

It replaces the ellipse by four circular arcs drawn with a compass inside the rhombus (the isometric square) round the circle. The two large arcs are centred at the 120° corners. The small arcs are centred where the lines from those corners to the midpoints of the opposite sides cross. All arcs meet at the side midpoints with a common tangent. For a rhombus of side s the radii are 0.866 s and 0.289 s. The result is slightly short along the major axis, by about 3.5% of the diameter.

Why does a sphere's isometric projection come out the true size?

Seen from any direction, a sphere's outline is a great circle at right angles to the line of sight, so its orthographic projection is a circle of the true radius R. In the isometric projection, draw the outline with radius R. In an isometric drawing everything is 1.2247 times larger, so use 1.2247 R. Locate the centre by measuring the isometric height R straight above the point where the sphere touches the surface it rests on: 0.8165 R on the paper in the projection. A hemisphere on its flat face shows the upper half of that circle and the front half of the base ellipse.

How do you draw a combination of two solids?

Start with the lower solid and draw it completely. The top face of the lower solid becomes the base of the upper one: find its centre, draw the axis up from it and build the upper solid on that axis. Measure every height along the vertical isometric axis from the ground, never along a sloping line. Finally remove the parts of the lower solid that the upper one hides, and the hidden edges of both, so only the visible outline remains.

Predict, then check

A sphere of 50 mm diameter is drawn in isometric projection (using the isometric scale). Its outline is

Worked examples

Cylinder by the four-centre method · Cylinder 50 mm in diameter, 70 mm high, axis vertical; isometric drawing (true lengths along the axes)
  1. Draw the rhombus round the top circle: sides 50 mm along the two horizontal isometric axes
  2. Large arcs: centres at the two 120° corners, radius = 0.866 × 50 = 43.30 mm
  3. Small arcs: centres on the long diagonal 14.43 mm either side of the centre, radius = 0.289 × 50 = 14.43 mm
  4. The four-centre ellipse measures 57.74 × 36.60 mm; the true ellipse is 61.24 × 35.36 mm, the largest gap 1.75 mm at the ends of the major axis
  5. Repeat the ellipse 70 mm lower for the base, draw its front half only, and join the two with vertical tangent lines. Overall height on paper = 70 + 35.36 = 105.36 mm

Answer: Arc radii 43.3 and 14.4 mm; the ellipse is drawn 1.8 mm short of the true one at each end, about 3.5% of D

Square pyramid by the box method · Square pyramid, base 40 mm with base edges along the isometric axes, height 60 mm; isometric projection
  1. Box: 40 × 0.8165 = 32.66 mm along each horizontal axis, 60 × 0.8165 = 48.99 mm high
  2. Base: the bottom face of the box. Apex: straight above the centre of the base, at the full box height
  3. Every lateral edge is truly √(20² + 20² + 60²) = 66.33 mm long
  4. On paper the front lateral edge is vertical and measures 65.32 mm; each side lateral edge measures 56.57 mm

Answer: Equal true edges (66.3 mm) draw at 65.3 and 56.6 mm: lateral edges are non-isometric lines, so locate the apex, never measure them

A sphere resting on a square slab · Sphere of 40 mm diameter resting at the centre of a square slab 60 × 60 × 15 mm; isometric projection
  1. Slab: 48.99 mm along each horizontal axis and 12.25 mm high
  2. Mark the centre of the slab's top face: that is where the sphere touches it
  3. Centre of the sphere: 20 mm true height above that point, drawn as 20 × 0.8165 = 16.33 mm straight up
  4. Outline: a circle of the TRUE radius, 20 mm, about that centre (no isometric scale on a sphere's outline)
  5. Overall height on paper, from the slab's lowest corner to the top of the sphere: 73.07 mm

Answer: Outline radius 20 mm, centre 16.3 mm above the contact point, total height 73.1 mm on paper

Chapter 23

Perspective and oblique projection

Which syllabus covers thisAU GE3251 Unit VVTU not in syllabusSPPU 102012 Unit VMU not in syllabusKTU not in syllabus

What makes perspective different from the other projections?

Orthographic, isometric and oblique views all use parallel projectors. Perspective uses converging ones: every ray runs from a point on the object to one point, the observer's eye, and the picture is where those rays cross a transparent picture plane. The result looks the way a camera or an eye sees. An object N times further from the eye appears N times smaller, so it is the natural choice for showing a building or a product, but not for taking measurements.

What are the station point, picture plane, ground line and horizon line?

The station point (SP) is the observer's eye. The ground plane (GP) is the horizontal plane the object stands on. The picture plane (PP) is a vertical plane between the eye and the object; the perspective is drawn on it. The ground line (GL) is where the picture plane meets the ground plane. The horizon line (HL) is where it meets the horizontal plane through the eye, so it lies above GL by the eye height. The foot of the perpendicular from the eye to the picture plane is the centre of vision, on the HL.

How does the visual-ray method build a perspective?

Draw the top view and the front view of the object and of the station point. In the top view the picture plane is a line: join the station point to each corner of the object, and mark where these visual rays cross that line. In the front view join the station point to the same corners. Project each crossing point vertically down until it meets the matching ray in the front view. That intersection is the corner in perspective; join the corners and draw the visible edges.

Perspective by the visual-ray method: station point, picture plane, horizon and vanishing points: interactive loads as you scroll

When do you get one vanishing point, and when two?

Parallel lines that are not parallel to the picture plane meet, in perspective, at a vanishing point on the horizon line. With a face parallel to the picture plane, only the edges going straight back recede, so all of them meet at the centre of vision: one-point perspective. Turn the object so its faces are at 30° and 60° to the picture plane and both sets of horizontal edges recede: two-point perspective. With the eye 100 mm from the picture plane, the vanishing points sit 57.7 mm and 173.2 mm either side of the centre of vision.

What is oblique projection, and what are cavalier and cabinet views?

Oblique projection uses parallel rays that strike the plane at a slant. One face, held parallel to the plane, shows in its true shape, so circles on it stay circles; that makes oblique quick for parts with round features on one face. Receding edges are drawn at a chosen angle, usually 30° or 45°. Cavalier oblique draws them at full length, which looks too deep; cabinet oblique halves them, which looks more natural. Unlike perspective, oblique keeps parallel lines parallel.

Predict, then check

Two identical lamp posts stand on a straight road, one on the picture plane and the other 20 m behind it. The eye is 10 m in front of the picture plane. In the perspective, the far post is

Worked examples

One-point perspective of a square prism · Square prism 30 × 30 × 40 mm high, one face parallel to the picture plane and 10 mm behind it, its axis 25 mm right of the station point; eye 90 mm in front of the picture plane and 55 mm above the ground
  1. Top view: rays from the station point to the near corners (10 mm behind the PP) cross the PP line at 90/100 of their offsets: 9.0 and 36.0 mm right of the central line
  2. Rays to the far corners (40 mm behind) cross at 90/130 of their offsets: 6.92 and 27.69 mm
  3. Front view: the near face's corners land at heights 55 − 55 × 0.9 = 5.5 mm and 55 − 15 × 0.9 = 41.5 mm; the far face's at 16.92 and 44.62 mm
  4. Near vertical edge: 36.0 mm tall; far vertical edge: 27.69 mm, a ratio of 100/130 = 0.769
  5. The receding edges, extended, meet on the horizon line straight in front of the eye: the centre of vision is the one vanishing point

Answer: Near face 27.0 × 36.0 mm, far face 20.77 × 27.69 mm, one vanishing point at the centre of vision

Where the vanishing points fall · A block standing with its vertical faces at 30° and 60° to the picture plane; eye 100 mm in front of the picture plane
  1. In the top view, draw lines from the station point parallel to the two sets of horizontal edges until they meet the picture-plane line
  2. The line parallel to the face at 60° to the PP meets it 100 × tan 30° = 57.74 mm to one side of the centre of vision
  3. The line parallel to the face at 30° meets it 100 × tan 60° = 173.21 mm to the other side
  4. Project both points onto the horizon line: the vanishing points are 230.94 mm apart
  5. The two lines from the station point are at 90°, as the faces are: a quick check on the drawing

Answer: VPs 57.7 mm and 173.2 mm either side of the centre of vision (230.9 mm apart)

Cavalier against cabinet oblique · A box 60 mm wide, 40 mm high and 50 mm deep, front face parallel to the plane, receding edges at 45°
  1. The front face is drawn true size: 60 × 40 mm
  2. Cavalier: receding edges full length, 50 mm at 45°; they add 50 cos 45° = 35.36 mm across and up
  3. Cavalier outline: 95.36 × 75.36 mm
  4. Cabinet: receding edges at half length, 25 mm, adding 17.68 mm; outline 77.68 × 57.68 mm

Answer: Cavalier 95.4 × 75.4 mm, cabinet 77.7 × 57.7 mm; the cabinet view looks less stretched

Chapter 24

Computer-aided drafting: coordinates, commands and layers

Which syllabus covers thisAU not in syllabusVTU BCEDK103 Module 1SPPU 102012 Unit IIMU not in syllabusKTU GMEST103 Module 4

Why draft on a computer at all?

Every point is stored as exact numbers, so a 60 mm line is exactly 60 mm, and dimensions read the geometry instead of a scale rule. Changes are edits, not redrawing: move a hole and its dimension follows. Repeated parts are copied, arrayed or saved as blocks and reused, and a template brings the sheet, border and title block ready-made. Layers keep visible lines, hidden lines, centre lines and dimensions apart. In 3D CAD the views themselves are projected from the model, but you still choose, read and dimension them.

How do you type points: absolute, relative and polar?

Absolute coordinates x,y are measured from the origin (0,0). Relative coordinates @dx,dy are measured from the last point, so @50,0 draws 50 mm to the right of wherever you are. Polar coordinates give a distance and an angle: @50<120 goes 50 mm at 120°, angles counted anticlockwise from the +x direction, negative angles clockwise. From (40, 30), @50<120 lands at (15, 73.30). With dynamic input switched on, the next point is relative by default and a # prefix forces absolute.

CAD drafting coordinates: absolute, relative and polar input for the LINE command: interactive loads as you scroll

Which commands do most 2D drawings need?

A short set covers most of first-year drafting. Draw: LINE, CIRCLE, ARC, POLYGON, RECTANG and HATCH. Modify: OFFSET (a parallel copy at a distance, ideal for wall thickness or a border), TRIM and EXTEND (cut or stretch lines to a boundary), FILLET and CHAMFER (round or bevel a corner), MIRROR (draw half of a symmetric part) and ARRAY (copies in rows or round a centre, such as bolt holes). Annotate with DIMLINEAR and its relatives. Object snaps pick exact endpoints, midpoints, centres and intersections instead of guessing with the mouse.

How should layers be set up for an engineering drawing?

Layers are the CAD version of the transparent overlays once used in manual drafting. Each layer carries its own colour, linetype and lineweight, and can be hidden or locked. A common practice is one layer per line type from chapter 1: visible outlines thick and continuous, hidden edges dashed, centre lines chain thin, and separate layers for dimensions, hatching and the title block. Draw on the right layer and every line gets the right style automatically. Keep geometry off layer 0, and start from a template that already has these layers.

Predict, then check

The last point is (40, 30). You type @50<120. Where does the line end?

Worked examples

An equilateral triangle with polar entries · LINE command: first point 20,20, then three sides of 60 mm
  1. 20,20 sets the start (absolute)
  2. @60<0 draws 60 mm along +x to (80, 20)
  3. @60<120 draws 60 mm at 120° to (50, 71.96): the turn of 120° gives the 60° interior angle
  4. C (close) draws the last side back to (20, 20); typing @60<240 instead lands on the same point
  5. Perimeter 3 × 60 = 180 mm, area (√3/4) × 60² = 1558.85 mm²

Answer: Corners (20, 20), (80, 20), (50, 71.96); perimeter 180 mm

A 30-60 set square · Right triangle with a 90 mm base and a 30° angle at the start point (20, 10)
  1. 20,10 then @90<0: the base, to (110, 10)
  2. The vertical side is 90 tan 30° = 51.96 mm: type @0,51.96 to reach (110, 61.96)
  3. C closes the hypotenuse: length √(90² + 51.96²) = 103.92 mm, rising at 30.00° from the start
  4. The same side could be typed from the top corner as @103.92<210 (pointing back down at 30° + 180°)

Answer: Sides 90, 51.96 and 103.92 mm; angles 30°, 60°, 90°; perimeter 245.88 mm

Turning absolute points into relative polar input · A path through the points (10, 10), (70, 45) and (30, 80)
  1. First leg: dx = 60, dy = 35, distance √(60² + 35²) = 69.46 mm, angle atan(35/60) = 30.26°
  2. Second leg: dx = −40, dy = 35, distance 53.15 mm; the angle is in the second quadrant: 180° − atan(35/40) = 138.81°
  3. So the entries are 10,10 then @69.46<30.26 then @53.15<138.81
  4. Check: adding r cos θ and r sin θ for both legs to (10, 10) returns (30, 80)

Answer: @69.46<30.26 and @53.15<138.81

Keep going

Recommended reading

  • Engineering Drawing, N. D. Bhatt and V. M. Panchal
  • Engineering Graphics, K. Venugopal and V. Prabhu Raja
  • Engineering Drawing (Vol. I and II), K. R. Gopalakrishna
  • A Text Book of Engineering Graphics, K. V. Natrajan
  • Engineering Drawing, N. S. Parthasarathy and Vela Murali
  • Engineering Drawing, D. A. Jolhe
  • SP 46: Engineering Drawing Practice for Schools and Colleges, Bureau of Indian Standards

How this book was made

Chapters follow the official syllabi listed above. Every interactive's formulas and every worked-example number were checked by script. Explanations, animations and examples are original to Skill-Lync. Topics informed by MIT OpenCourseWare 2.007 (Design and Manufacturing I), CC BY-NC-SA. All explanations, animations and examples are original to Skill-Lync; MIT does not endorse this page.

From the exam to a core job

Talk to a counsellor.

Ask how design engineers use engineering graphics on real projects, and what the AutoCAD Essentials for Mechanical Engineers covers.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.