NACA airfoil calculator

Coordinates for any NACA 4- or 5-digit section, ready for SOLIDWORKS, CONVERGE or XFOIL. Lift, pitching moment and the pressure along the surface from an inviscid panel method, the critical Mach number, and what changes when the flow is supersonic. Free, no sign-up, runs in your browser.

The last tab checks a "flow over an airfoil" report: the regime, the Reynolds number, the coefficients and the slips that show up in the forces. Skill-Lync read 367 of those reports to build it.

NACA equations as in Abbott & von Doenhoff · panel method checked in Python with a different method and against an exact airfoil · Updated 20 Nov 2026

4-digit codes (2412, 0012, 4415) or non-reflexed 5-digit (23012, 24012). Cosine spacing. The .dat file is in chords, Selig order (trailing edge, upper surface, nose, lower surface); the SOLIDWORKS and CSV files are scaled to the chord and turned nose-up by α.

Max thickness12%at 29.9% chord
Max camber2%at 40% chord
Nose radius1.59%area 0.0818 c²
NACA 2412 · α 0° · flow →mean camber linemax thickness 12% at 29.9% chord
  • Zero-lift angle -2.077°, quarter-chord moment -0.05312 (thin-airfoil theory). Open the Lift and pressure tab for the panel method.

What do the "flow over an airfoil" projects ask?

Skill-Lync has 367 public reports with airfoil or NACA titles. Two briefs account for most of them. In the SOLIDWORKS Flow Simulation exercise (162 reports name SOLIDWORKS), students import a NACA 0017, run a 2-D external flow at 0°, 2°, 4°, 6°, 8° and 10°, and compare lift and drag; 143 of the reports set the inlet to 600 m/s. In the CFD mini project (CONVERGE), it is a NACA 2412 with a 0.1 m chord at Re = 200,000 and 1°, 5°, 10° and 15°, run with two turbulence models (43 reports use k-ω SST, 42 k-ε or RNG k-ε).

Both start with coordinates, which is what the first tab makes. The findings below come from reading all of them.

The NACA 4-digit and 5-digit equations

A NACA 4-digit code MPXX means a maximum camber of M% of the chord, at P tenths of the chord, and a maximum thickness of XX%. NACA 2412: 2% camber at 40%, 12% thick. The thickness distribution is the same for every 4- and 5-digit section (x in chords, t the thickness as a fraction):

Its last coefficient leaves the trailing edge open, 0.0025 chords thick for a 12% section. Changing −0.1015 to −0.1036 closes it, which is what a CAD sketch and a CFD mesh want. The mean camber line is two parabolas that meet at x = p:

The thickness is laid out perpendicular to the camber line, not straight up from the chord:

A 5-digit code LPQXX keeps the thickness and uses a cubic camber line: the design lift coefficient is 0.15 L, the camber peaks at P/20 of the chord, and Q = 0 means a normal (not reflexed) line. NACA 23012 is designed for cl = 0.3 with its camber peak at 15%. The nose radius of every section is 1.1019 t², 1.587% of the chord for a 12% section.

Lift: thin-airfoil theory, the panel method and real data

Thin-airfoil theory treats the section as its camber line. The lift grows by 2π per radian (0.1097 per degree), starting from a zero-lift angle that depends only on the camber:

For NACA 2412 that gives αL=0 = -2.077° and a quarter-chord pitching moment of -0.053, the values in Anderson's Fundamentals of Aerodynamics. The panel method in the second tab adds the thickness: it covers the surface with 200 vortex panels whose strength varies linearly along each, and makes the flow leave the trailing edge smoothly (the Kutta condition). Thickness raises the inviscid slope a few percent above 2π. Real air takes some of it back through the boundary layer, and stalls the section:

NACA 2412, αThin airfoilPanel (inviscid)XFOIL Re 200,000XFOIL Re 1,000,000
0°0.2280.2580.286 (cd 0.0100)0.244 (cd 0.0057)
1°0.3370.3780.426 (cd 0.0098)0.347 (cd 0.0055)
5°0.7760.8580.801 (cd 0.0123)0.809 (cd 0.0080)
10°1.3241.4501.161 (cd 0.0270)1.270 (cd 0.0159)
15°1.8732.0301.286 (cd 0.0668)1.560 (cd 0.0314)

XFOIL polars from Airfoil Tools (Ncrit 9). Maximum lift: 1.328 at 14.25° (Re 200,000), 1.582 at 16.5° (Re 1,000,000). The panel method has no stall: at 15° it is far above any real section.

Below about 8° the inviscid and the viscous curves stay close; at Re = 200,000 laminar separation bubbles even push XFOIL's lift above the inviscid line near 1°. Above that the boundary layer thickens and separates from the trailing edge forward, and the curves part. Drag never comes out of a panel method. A flat plate of the same chord with friction on both sides gives a floor and a ceiling for it: cd = 0.0059 if the boundary layer stays laminar and 0.0123 if it is turbulent from the nose, at Re = 200,000. XFOIL's 0.0100 at 0° sits between them.

The Re = 200,000 brief: 31.4 m/s and a 15° stall

With a 0.1 m chord in air at 300 K:

40 reports work in this brief. Those that type out a speed use 30 m/s (Re ≈ 1,91,226) or 31.4 to 31.8 m/s; 31.51 m/s comes from ρ = 1.1765 kg/m³ and μ = 1.8538 × 10⁻⁵ Pa·s. Any of these is close enough. The coefficient needs a reference area: chord times the depth of the 2-D domain, which in CONVERGE is the thickness of the one-cell slab. Dividing by the wrong depth, or by a "frontal area", is the most common way to get a lift coefficient that is off by a factor.

The reports that typed their coefficients out show the same pattern. One gives cl = 0.364, 0.781, 1.257 and 0.941 at 1°, 5°, 10° and 15°; two others give 0.378, 0.748, 1.075, 0.906 and 0.331, 0.662, 0.904, 0.751. All stall between 10° and 15°. XFOIL at the same Reynolds number reaches its maximum at 14.25° and is still at 1.286 at 15°. RANS models with wall functions on a coarse 2-D mesh tend to put the stall too early, and k-ε more than k-ω SST. The check tab marks where your run stalls against XFOIL's maximum.

600 m/s is Mach 1.75: what the SOLIDWORKS results really show

The speed of sound in air at 293.2 K is 343.3 m/s, so 600 m/s is Mach 1.748. That is supersonic. Of the 143 reports that use 600 m/s, 135 never mention a shock or supersonic flow, and 37 describe it as subsonic. 13 explain the drag rise by the airfoil's frontal area growing with the angle.

Supersonic linear theory (Ackeret) says what the forces should do. For a section at small angles:

At Mach 1.748 that is cl = 0.097 at 2° and 0.487 at 10°, rising in a straight line, with no stall. The exact flat plate (an oblique shock below, a Prandtl-Meyer expansion above) gives 0.496 at 10°. To second order a symmetric section has the same lift as a flat plate, so the 17% thick nose matters for drag, not lift. The drag due to lift is cl·α: the pressure force is roughly normal to the chord, so tilting it by α adds a drag component of lift × tan α.

Skill-Lync could read the lift and drag tables in 21 of the reports. A typical one:

αDrag (N)Lift (N)L/D(D − D₀) / Ltan α
0°303.8-0.2––0.000
2°332.5825.42.480.0350.035
4°414.41641.23.960.0670.070
6°551.92430.54.400.1020.105
8°738.73207.64.340.1360.141
10°1007.34033.44.000.1740.176

The forces follow the supersonic theory closely. Lift is linear in α. The drag rise from 0° to 10° is 0.174 of the lift, against tan 10° = 0.176: that is the tilted pressure force. In 17 of the 21 tables L/D at 10° is 4.00 to 4.06 (some tables appear in more than one report), and in 16 of those 17 the drag rise is 0.16 to 0.18 of the lift. An inviscid flat plate could reach L/D = cot 10° = 5.67; the bow shock on the round nose and friction bring it down to 4.

So the simulations are sound. The write-ups are what go wrong: the drag does not rise because more area faces the flow, and nothing stalls at 10°. Without the depth of the 2-D domain the coefficients cannot be recovered from these forces, but they fix q·S: 8283 N at 10° if the run matches Ackeret, i.e. a reference area of 0.0382 m². The check tab does this for your own table.

Critical Mach number

Below Mach 1, the air speeds up over the upper surface. The free-stream Mach number at which the fastest point just reaches sonic is the critical Mach number. The panel method gives the lowest pressure coefficient at low speed, Cp,0; the Karman-Tsien rule scales it with Mach number, and the critical Mach is where it meets the sonic value Cp*:

NACA 0012 at 0°: the panel method gives Cp,0 = -0.414, so Mcr = 0.729 by Karman-Tsien, or 0.742 by the simpler Prandtl-Glauert rule (Anderson's example uses the measured −0.43 and gets 0.74). Lift moves the suction peak up: at 5° the critical Mach of NACA 2412 drops to about 0.48.

Getting the coordinates into SOLIDWORKS, CONVERGE and XFOIL

  • SOLIDWORKS: Insert > Curve > Curve Through XYZ Points, browse to the .txt (X, Y, Z per line, in millimetres here), OK. Convert Entities onto a front-plane sketch, extrude or use it as the 2-D section. The file is already scaled and turned nose-up by your α about the point you chose, and the last point repeats the first so the curve closes.
  • CONVERGE Studio: reports add each point as a vertex (Geometry > Create > Vertex) and patch them with an ordered vertex list, then extrude by the domain depth. Use the CSV or .dat and scale x and y by the chord.
  • XFOIL: LOAD the .dat file (Selig format: the name on the first line, then x y from the trailing edge over the upper surface to the nose and back along the lower surface), then PANE to repanel. XFOIL also builds NACA sections itself (NACA 2412).

Use the closed trailing edge for CAD and meshing; a 0.25% open gap at the tail turns into a tiny face that the mesher must resolve.

Which slips does the check tab catch?

  • The wrong regime: the Mach number from your speed and temperature, and which theory applies.
  • The wrong Reynolds number: the speed that gives 200,000 for your chord.
  • The wrong reference area: coefficients above the inviscid value, and the depth that would make them fit.
  • Lift and drag swapped, or body-axis forces: drag above lift at moderate angles, negative drag after tilting the inflow.
  • Lift on a symmetric section at 0°, drag that dips below its 0° value: geometry, convergence or averaging problems.
  • Supersonic runs: L/D against cot α, the drag rise against tan α, and whether lift is linear in α.
  • Stall: where your lift drops, against XFOIL's maximum for NACA 2412 and 0012.

What this calculator does not cover

  • Viscous drag and stall. The panel method is inviscid. The XFOIL reference points cover NACA 2412 and 0012 at two Reynolds numbers only.
  • Transonic flow. Between about Mach 0.7 and 1.2 shocks sit on the surface; none of the theories here holds.
  • Blunt-nose supersonic effects. The bow shock's stand-off and the subsonic pocket at the nose need a numerical solution. Linear theory gets the lift; the zero-lift drag of a round-nosed section it cannot.
  • 3-D wings. Finite span adds induced drag and lowers the lift slope; this is a 2-D section.
  • 6-series and other families. Only NACA 4-digit and non-reflexed 5-digit sections are generated.
Learn CFD

Setting up an external-flow case, picking a turbulence model, getting the reference area right and comparing with data is everyday work for a CFD engineer. The airfoil case is part of Skill-Lync's PG Program in CFD.

Frequently asked questions

How do you get NACA airfoil coordinates?

Pick the code, then compute the camber line and thickness from the NACA equations and lay the thickness perpendicular to the camber line. For NACA 2412 the maximum camber is 2% of the chord at 40%, and the maximum thickness 12% at 29.9%. The calculator gives the points with cosine spacing (dense at the nose and tail) as a Selig .dat file, a SOLIDWORKS XYZ curve in millimetres or a CSV.

How do I import airfoil coordinates into SOLIDWORKS?

Insert > Curve > Curve Through XYZ Points, browse to the .txt file (three columns X Y Z, in the part's units) and click OK. Convert the curve into a sketch (Convert Entities) on the front plane, close the trailing edge if it is open, then extrude it or use it as the 2-D section for a flow simulation. Rotate the sketch about the quarter chord for each angle of attack, or tilt the velocity vector instead.

What is the lift coefficient of NACA 2412?

Thin-airfoil theory gives cl = 2π(α + 2.077°) per radian: 0.776 at 5°. The inviscid panel method gives 0.858. XFOIL at Re = 200,000 gives 0.801 at 5° and a maximum of 1.328 at 14.25°; at Re = 1,000,000 the maximum rises to 1.582 at 16.5°.

What is the zero-lift angle of NACA 2412?

-2.077° by thin-airfoil theory, with a quarter-chord pitching moment of -0.053. Symmetric sections (NACA 00xx) have zero-lift angle 0°.

Is 600 m/s subsonic for an airfoil simulation?

No. At 20 °C the speed of sound is 343.3 m/s, so 600 m/s is Mach 1.748: supersonic. A round-nosed NACA section then carries a detached bow shock, its lift follows supersonic theory (cl ≈ 4α/√(M² − 1) = 0.487 at 10°) and the drag rises with angle by about cl·α. Explanations about stall or a growing frontal area do not apply.

What velocity gives Re = 200,000 for a 0.1 m chord?

About 31.4 m/s in air at 300 K (ρ = 1.177 kg/m³, μ = 1.846 × 10⁻⁵ Pa·s). Reports that use ρ = 1.1765 and μ = 1.8538 × 10⁻⁵ get 31.51 m/s; 30 m/s gives Re ≈ 1,91,226.

What does a panel method not predict?

Drag and stall. It solves inviscid, attached flow, so it gives the lift, the pitching moment and the pressure along the surface well below stall, but no skin friction and no separation. For drag and maximum lift you need a viscous method (XFOIL couples a panel method with a boundary layer), CFD or a wind tunnel.

Related on Skill-Lync

Sources

  • I. H. Abbott and A. E. von Doenhoff, Theory of Wing Sections (Dover, 1959): the NACA 4- and 5-digit thickness and camber equations and the 5-digit camber constants.
  • J. D. Anderson, Fundamentals of Aerodynamics, ch. 4 (thin-airfoil theory; NACA 2412 αL=0 = −2.077°, cm,c/4 = −0.053), ch. 11 (Prandtl-Glauert and Karman-Tsien rules, the critical Mach number of NACA 0012) and ch. 12 (linearised supersonic flow).
  • A. M. Kuethe and C.-Y. Chow, Foundations of Aerodynamics: the linear-strength vortex panel method used by the page.
  • Airfoil Tools, XFOIL polars NACA 2412 at Re 200,000, Re 1,000,000 and NACA 0012 at Re 200,000 (Ncrit 9), fetched 20 Nov 2026.
  • Skill-Lync, 367 public airfoil reports, read 20 Nov 2026: briefs, inlet speeds, turbulence models, force tables and coefficients.
  • Skill-Lync, scripts/verify/airfoil.py: a Hess-Smith panel method (sources plus a uniform vortex) checked against the exact lift of Karman-Trefftz airfoils, thin-airfoil integrals by adaptive quadrature, the exact flat plate with the wave angle from NACA Report 1135's cubic, and the critical Mach number by root-finding. The page re-checks every number against it when it is built.
Free counselling

From an airfoil case to a CFD career.

Getting the physics of a case right, then explaining the gap to theory and data honestly, is what CFD roles ask for. A Skill-Lync counsellor can tell you which CFD course fits where you are now.

Talk to a CFD course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.