Wiring harness routing & packaging Rules Week 3 Challenge

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing,   Download connector 3D data from www.te.com   DT06-4S DT06-6S DT06-2S DT06-08SA Check the bundle Continuity. Add snap of result in submission…

AIM:= Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.   Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2…

 Objective:      To design of Butterfly Valve in appropriate dimension with the application of GD&T - ASME Y14.5 2009. To assemble all the individual parts of the butterfly valve by assigning suitable constraints. To understand the concept of geometric tolerance and dimensioning.   …

Week 12- Final project: Development of a Door Trim panel Door trim panel is creation of CAD model considering following inputs as like in OEM and tier1 companies Class A surface is givin but after applying boundries check, it has been found there is some improvement needed to be actioned to get a closed surface. Nominal…

AIM: To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. CLASS A SURFACE:           Class A is an aesthetic surface with the highest quality finish. Most Class A Surfaces for…

Objective: The main aim of this challenge is to create a solid body of 'Door Trim Lower' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Door trim. Overview:Initially, we need to offset the given Door…

Attachment Feature Creation - Challenge 2 AIM Create the Dog House for the Door Trim considering the design rules INTRODUCTION DOG HOUSE Dog house is an engineering feature used in plastic design. Dog houses are used as support feature. Sometimes other engineering features like snaps, locators, and screw bosses are mounted…

Objective: The main objective of this challenge is to create the B-side features RIBs and Screw Bosses for a given drill handle. Overview: Creating the class B and class C surfaces to the door handle, and creating the B side features (RIBs and Screw Bosses) by considering all the design parameters.Design parameters…

AIM Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 3 mm REPORT…

ANSWER: BASE BRACKET DESIGN AIM: To create the Base Bracket Plastic component through the given Class-A surface by creating a tooling axis meeting the requirements of the draft angle and to perform the Draft Analysis on the solid model at the end.  GIVEN CLASS A SURFACE:            …

AIM: To create  the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.   CAD DATA: The  CAD DATA…

1.0 AIM Use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses 2.0 INTRODUCTION 2.1 BACK DOOR   Back door or tail gate  simply refers to the back of the car that can open and close.it covering the…

Aim: For the given roof styling, develop the essesntial flanges and reinforcements, provide appropriate dimensions and check for draft analysis and to perform roof curvature study using NX-CAD Introduction: Roof An automobile roof or car top is the portion of an automobile that sits above the passenger…

DESIGN OF CAR FENDER Fender is  the part of an automobile, motor cycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into the air by the rotating tire. Fenders are typically rigid and can…

Objective             To calculate the wheel arc for given Fender model, by means of the European standards regulations.  Introduction             Wheel arc calculation is necessary for the fender design to pass the local regulation which are based on the local road conditions.             Wheel arch is a semi-circular…

Problem Statement: - Use the Section from your Hood design and calculate the section modulus using the formula S = I/y S = Section Modulus I = Moment of Inertia Y = distance between the neutral axis and the extreme end of the object Come up with a new section that has improved the section modulus of the previous section…

                                                                                           …

Objcetive: >> Writing a one-pager about Under-Body Coating and its purpose, its types in detail, and its pros and cons.   What is under Body Coating: Underbody coating is a thick cladding (typically made of rubber) that is placed uniformly to the car’s underside. When the automobile is fresh…

Project Objective:- In This Project, I am Going to Suggest a Big Car for Mr.D.S. Pughazhyendhii Under 8 to 10 Lakhs on Road for Official and Family Purpose Traveling Distance Around 500km. 01. Suggested Cars Listed Below:-  01. Hyundai Vennu 1.4 CRDi MTE. 02. Mahindra XUV 3000 1.5W6. 03. Nissan Kicks XE Diesel.…

Title: Defining Connectors and Clips using CATIA V5 Objective : Downloading the 3D CAD files form the te.com website and then defining the parts electrically and further creating a catalogue for the components. Introduction:  A connector is a device(or more precisely, a mating pair of devices, often a plug…

 Objective: To create quick return mechanism and CV joint parts in part workbench or generative work bench and assemble themfollowing guidelines   CV JOINT  2. CV JOINTConstant-velocity joints (also known as homokinetic or CV joints) allow a drive shaft to transmit power through a variable angle, atconstant…

AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2…