Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge

Aim- To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective- The objective of the project is to route the wiring harness on given V16 Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry best…

Statement of assignment: Route the Wiring harness on the Given car body and Prepare to flatten the view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be used,…

Q1. Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view. AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING:…

                                                                                           …

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download…

 Wiring harness routing & packaging Rules Week 3 Challenge Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Hellarmann Tyton – 21160129 process: Create two points one as entry and another as exit point.…

  DEFINIG ELECTRIC PARAMETER FLOW CHART CONNECTOR DEFINATIONS IN CATIA V5 1. Deutsch DT06 – 08SA Connector connection point: Create midpoint on the contact face which will be normal to wire bunddle insertion. Craete Axis System with respect to the point which we have created and defining the axis direction…

Assemble and apply GD&T to the butterfly valve assembly drawing Butterfly valve: working principle The construction of a butterfly valve is relatively simple, with the rotation of the valve disc controlling the fluid flow. In the closed position, the disc blocks the valve bore while in the open position, the disc…

   FINAL PROJECT                                                                                                            DOOR TRIM DEVELOPMENT  INPUTS: CLASS A surfaces of the DOOR ARM REST, MAP POCKET, BOTTLE HOLDER and LOWER SUBSTRATE. Master section for the attachment features. Push clips for the assembly. OBJECTIVES:…

   FINAL PROJECT                                                                                                            DOOR TRIM DEVELOPMENT  INPUTS: CLASS A surfaces of the DOOR ARM REST, MAP POCKET, BOTTLE HOLDER and LOWER SUBSTRATE. Master section for the attachment features. Push clips for the assembly. OBJECTIVES:…

AIM:   To design and development of vehicle interior door trim using Catia V5 with given class A surface along with Master section. Also create the Side Attachment features as per design rules.   OBJECTIVE:   To create thickened part using master section for reference To create the mounting features as per…

  QUICK RETURN MOTION MECHANISM:   SLOTTED LEVER:   BASE:   RECTANGULAR SLIDER:   CONNECTING ROD:   CIRCULAR SLIDER:   ASSEMBLY:     DRAFTING:   CV JOINT:   PART 1:   PART 2:   PART 3:   ASSEMBLY:     DRAFTING:  

                                                                                         A…

AIM:-- Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create the Heat Stakes and the locators considering…

Question: Create the Dog House for the Door Trim considering the design rules mentioned in the video. Consider the thickness of the part to be 2.5 mm. "C" is where the doghouse contacts the backside of the surface.  Doghouse wall thickness at the intersection of the part wall ( C ) should be 40% or…

                                                                            Attachment Feature Creation (Ribs & Screw Boss)…

AIM Create Core and Cavity for the existing Switch Bezel design and Show Draft Analysis using existinng Tooling Axis. OBJECTIVE Create Parting Surface and Parting Line for Switch Bezel. Create Core And Cavity Blocks. Show Draft Analysis Component with the Core and Cavity. Make Solid a Body Using Close Surface Feature from…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface.CLASS-B SURFACE: a surface below a certain thickness from the class-A…

Aim: To be able to model solid from the given Class a surface, and perform Draft analysis and create Tooling axis. Class A surface with tooling axis. COIN HOLDER To create a coin holder plastic component by closed method with reference to the class A surface and do the draft analysis for the component. Steps followed The…

- Aim: Create the Switch Bezel Plastic component through the given Class-A surface. - Objectives: - To create class B & C surface for the given component. - To form the tooling axis and capture the surface properly. - To check the feasibility of the component with a draft of 3 degrees. - Method: - In…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. REPORT ON DRAFT ANALYSIS: Given Class A Surface: STEP…

CAR BACK DOOR DESIGN Aim: To design back door of car using given outer class 'A' surface. What is back door of a car? A door which is located at the rear side of a car which gives access for the boot space to store luggage, spare wheel etc. These doors can be operated manually or electric powered. In most of…

OBJECTIVE We need to design the required reinforcment and flanges for the given Class A surface of Roof.Required reinforcments are Front Roof Rail,Rear Roof Rail,Bow Roof 1,Bow Roof 2.After designing the roof assembly completely we need to perform the Heat distortion analysis and the Snow Load Analysis.…

Aim: To decide whether the given design passes the European standards or not.   Given Design:   European Regulations Requirement:   Take the outline of the wheel and the fender. Make the centre of the wheel circle. Draw horizontal and vertical perpendicular axes from the centre of the wheel circle. Draw lines at 30 degrees…

                                                                    Report On Section Modulus Calculation Of Hood Aim  To calculate the section…

Fender is  the part of an automobile, motor cycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into the air by the rotating tire. Fenders are typically rigid and can be damaged by contact…

Design Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section mentioned with the Design parameters explained in the videos.   Submit an ASSEMBLY of Hood Inner Panel, Outer Panel, Latch, Hinge and the Reinforcements.A detailed report about the Hood Design which includes a detailed…

  Writing a one-pager about Under-Body Coating and its purpose, its types in detail, and its pros and cons.  What is under Body Coating: Underbody coating is a thick cladding (typically made of rubber) that is placed uniformly to the car’s underside. When the automobile is fresh off the lot…

1. Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, a five-year-old boy, his father, and his mother. He visits his native place Madurai…

Identify each of the major elements in the above automotive wiring diagram.  There are some major elements like 1)GENETRATOR. 2) CURRENT AND VOLTADE REGULATOR . 3) BATTERY. 4) STARTER 5) BREAKER. 6) DISTRIBUT0R. 2. Explain the purpose and working of any three elements briefly. i)BATTERY A battery is a device that stores…

Objective of Main Project: Developing Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink. Follow all the MBD related processes: Requirement Tagging & Traceability, SLDD creation, Configuration Parameter changes, Model Advisor check & Code Generation. In Configuration Parameters: enable…

 Mini Project - Vehicle Direction Determination Simulink model: We have created  Subsystem. After creating subsystem we have requirement1 and requirement2 port 1 (Logic Now in the Subsystem) After this. Requirement1 Requirement2 The SLDD_file is created to store the calibration values and input and output signals. …

   For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB.              this will be based model which we are going to use for our project by doing some…

Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions. A123’s high-performance Nanophosphate lithium iron phosphate (LiFePO4) battery technology delivers high power and energy density combined with excellent safety performance and extensive…

1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation ?  Hint :(Download the file from the link and go to SOC estimation model-ECU block)   After downloading…

Matlab code: clear all close all clc disp(' RANKINE CYCLE '); disp('1-2 is Constant pressure heat addition in the boiler'); disp('2-3 is Isentropic Expansion in the Turbine'); disp('3-4 is Constant pressure heat removal in the Condenser'); disp('4-1 is Isentropic compression in the pump'); p1 = input('nValue of pressure…

Cp=specific heat R=molar gas constant T=temperature S=Entropy H=Enthalpy t=coefficients   Code for calling function specific heat(): function Cp = specific_heat(t1,t2,t3,t4,t5,t8,t9,t10,t11,t12,T,R,global_midtemp) %calculating specific_heat for global_hightemp and global_lowtemp if(T>= global_midtemp) Cp=R*(t1+(t2*T)+(t3*(T).^2)+(t4*(T).^3)+(t5*(T).^4));…

ODE FUNCTION PROGRAM function [dtheta_dt] = ode_func(~,theta,b,g,l,m) theta1 = theta(1) theta2 = theta(2); dtheta1_dt = theta2; dtheta2_dt = -(b/m)*theta2 - (g/l)*sin(theta1); dtheta_dt = [dtheta1_dt; dtheta2_dt]; end * Ode45 function is which solve the simple differential equation with a certain specified command.…

From Live Session Introduction BATTERY: Batteries are a collection of one or more cells whose chemical reactions create a flow of electrons in a circuit. All batteries are made up of three basic components: an anode (the '-' side), a cathode (the '+' side), and some kind of electrolyte (a substance that chemically…

function [stalagmite] = stalagmite_func(input_vector) x= input_vector (1); y = input_vector (2); f1 = (sin(5.1*pi * x +0.5)).^6; f2 = (sin(5.1*pi * y +0.5)).^6; f3 = exp((-4*log(2)).*(x-0.0667)^2/(0.64)); f4 = exp((-4*log(2)).*(y-0.0667)^2/(0.64)); stalagmite = -(f1*f2*f3*f4); end STALAGMITE FUNCTION A stslsgmite function…

EXPLANATIONOF CODE clear all - To clear all the variables from the current workspace. close all - It close all figures whose handles are visible. clc - clc clears all the taxt from the command window. l1 - l1 is length of 1st link. l2 - l2 is length of 2nd link. theta - theta1 and theta2 an array, which have 20 values…