Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge

Objcetive: >> Writing a one-pager about Under-Body Coating and its purpose, its types in detail, and its pros and cons.   What is under Body Coating: Underbody coating is a thick cladding (typically made of rubber) that is placed uniformly to the car’s underside. When the automobile is fresh…

Project Objective:- In This Project, I am Going to Suggest a Big Car for Mr.D.S. Pughazhyendhii Under 8 to 10 Lakhs on Road for Official and Family Purpose Traveling Distance Around 500km. 01. Suggested Cars Listed Below:-  01. Hyundai Vennu 1.4 CRDi MTE. 02. Mahindra XUV 3000 1.5W6. 03. Nissan Kicks XE Diesel.…

Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be used, or you can download the connectors…

Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be used, or you can download the connectors from www.te.com…

Q1. Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view.     %ANSWER  

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)   Download connector…

Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp Note: if you face any issue with point definition, point selection, Right-click on the point definition window and use the reset option.  %ANSWER The given clip…

Q1. Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.   Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2…

%ANSWER   ''' Demonstrating file parsing in python ''' # data analysis import math import numpy as np import matplotlib.pyplot as plt from scipy.integrate import simps from tabulate import tabulate # file parsing with uer input # file input File = input("Enter the name of CONVERGE output filename with extension (.out):…

1. What does popt and pcov mean? (Watch the video to get some context) 2. What does np.array(temperature) do? 3. What does the * in *popt mean? 4. Write code to fit a linear and cubic polynomial for the Cp data. Explain if your results are good or bad.  5. What needs to be done in order to make the curve fit perfect?…

    import numpy as np from scipy.integrate import odeint import matplotlib.pyplot as plt import math # function that returns dz/dt def model(theta,t,b,g,l,m): theta1 = theta[0] theta2 = theta[1] dtheta1_dt = theta2 dtheta2_dt = -(b/m)*theta2 - (g/l)*math.sin(theta1) dtheta_dt = [dtheta1_dt, dtheta2_dt] return…

1. Your code should create a PV diagram 2. You should output the thermal efficiency of the engine. """ otto cycle simulator """ import math import matplotlib.pyplot as plt def engine_kinematics(bore,stroke,con_rod,cr,start_crank,end_crank): """ engine_kinematics """ #geometric parameters a=stroke/2 R=con_rod/a #volume…

For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB.    %ANSWER   Component Requirement: Battery (Table-Based): to activate the SoC and Thermal Property Click on the battery block…

Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions.   %ANSWER   ABSTRACT                   In this project, we are going to calculate the all parameters which are required…

1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation ?  %ANSWER1.Simulate the 3 test cases from harness dashboard and write a detailed report on the resultsTo…

1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it %ANSWER Li-ion Batteries A lithium-ion battery or Li-ion battery is a type of rechargeable battery. Lithium-ion batteries…

Description:As discussed in Lecture 11, Project 2 deals with the development of a forward energy-based fuel consumption model of a P1 hybrid vehicle. This model is based on the conventional vehicle model from Project 1. The main goal of this project is to understand the functionality of a P1 hybrid and be able to model…

Description:Project 1 deals with the development of a forward energy-based fuel consumption model of a conventional vehicle. The main goal of this project is to get familiar with the modeling process, writing scripts in Matlab, modeling in Simulink, analyzing data and generating plots. In this project, a typical midsize…

%Answer   scope   result  

Project %Answer PDI control desing dc motor model is here PDI control desing dc motor output is here

%Answer A = xlsread('VI.xlsx'); V = A(:,1); I = A(:,2); x = [-17.3:0.1:0.9]; y = interp1(V,I,x,'spline') plot(V,I,'r',x,y) intervoltage =[I, V] intercurrent = interp1(V,I,intervoltage) Z = [intervoltage intercurrent] field = fopen('intervoltage intercurrent.txt','w'); fprintf("%f",Z); fclose(field)  

1.]  a)generator       b)battery       c)starter       d)breaker       e)ammeter       f)ignition col       g)fues       h)current and voltage regulator 2.] Generator:                       it uses mechanical energy supplied to it to force the movement of electric charges present in the wire of its windings through an…

1.]  a)generator       b)battery       c)starter       d)breaker       e)ammeter       f)ignition col       g)fues       h)current and voltage regulator 2.] Generator:            …