Week 9 - Project - A pillar Design with Master Section

  Aim : Route the Given harness layout in Electrical workbench & Apply the Conditions. Ojectives : Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc Check for the bundle warning. Add snap. Generate CAT.part of harness…

  AIM: To route the wiring harness for the given engine. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. DESIGN CRITERIA AND PACKAGING ASSUMPTIONS: Wiring harness routing shall provide ease in manufacturing, accessibility,…

  OBJECTIVE: Route the Wiring harness on Given Engine and Prepare flatten view drawing on CATIA V5 .Application of all Packaging rules, Industry best practices studied in the course shall be demonstrated in design .Apply Protection coverings as required. Prepare and Submit all necessary reports like clearence,Clipping/Clamping…

Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge AIM Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view.       PROCEDURE STEP 1: Mechanical Part into Electrical Part Creation…

Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge   AIM Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end…

Wiring harness routing & packaging Rules Week 3 Challenge Aim Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp Download following Back shell cad data & define it as Electrical back shell using Electrical Part design…

  Wiring harness design in CATIA V5 – 3D modelling Week 2 Challenge Aim: Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 –…

  BACKDOOR           The Back door/Tail Gate of a car is a component which hinges at the back of the car to cover the boot space or luggage area, but there are more functions that come with it which has to be considered while making a design of the same like rear visibility criteria and boot…

ROOF         An automobile roof is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Though it just looks like a styling surface that protects from sun, wind and other elements, various environmental…

SECTION MODULUES                Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. Other geometric properties used in design include area for tension and shear, radius of gyration for compression, and moment of…

AIM :           To design part models and assemble the parts from the 2D sketches and dimensions provided to me. EXERCISES: QUICK RETURN MECHANISM                    2.CV JOINT 1.QUICK…

AIM: To design a  Front Fender OBJECTIVE: To design a Fender mounting on the given model by using Master sketch by considering the safety and manufacturing feasibility for possible mounting region.                                                                       …

FENDER WHEEL ARCH CHALLENGE FENDER WHEEL ARCH                                     Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. The design of the wheel arch of the fender should be such that it must shield wheels and protect both passengers’ compartment and pedestrians from…

AIM: To design the Hood or Bonet of the front driving car by using the master section and standard procedure which is used in the OEM Manufacturer's. GIVEN MASTER SECTION: HOOD or BONET: Hood is the component which is placed over the engine compartment. The design of the hood is not only to enhance the look of the car,…

AIM :-  Write a one-pager about Under-Body Coating and its purpose, its types in detail, and its pros and cons.   Under-Body Coating- Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed…

BENCHMARKING :- A specific, distinctive vehicle attribute branding is essential to make cars unique and competitive. As a first step on the way, vehicle manufacturers have to benchmark their vehicles in the competitive environment in order to understand and to strengthen or improve the potential of their vehicles.…

AIM     To make a full solid model from the provided master section and class A surface. INTRODUCTION: CATIA:          It means Computer-Aided Three-Dimensional Interactive Application.  It is computer aided designing software. This is software which…

A PILLAR DESIGN WITH MASTER SECTION :- Aim- Create A Pillar design using given class A surface and master section considering all design standerds. Use master section to create engineering feature.     Given Class A- Class B Creation- To create class B surface offset the class A with proper direction and…

Door Trim Lower with Engineering Features :- Aim- Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create…

DOG HOUSE CREATION FOR DOOR TRIM :- Aim- Create the Dog House for the Door Trim on Class B Surface considering the design rules. Consider the thickness of the part to be 2.5 mm.   Dog House- Purpose- SHINK MARKS-    Dog house helps to avoid shink marks. If a thick screw boss or rib needed…

Door Trim Lower with Engineering Features :- Aim- Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create the…

DOG HOUSE CREATION FOR DOOR TRIM :- Aim- Create the Dog House for the Door Trim on Class B Surface considering the design rules. Consider the thickness of the part to be 2.5 mm.   Dog House- Purpose- SHINK MARKS-    Dog house helps to avoid shink marks. If a thick screw boss or rib needed…

Attachment Feature Creation (Ribs & Screw Boss) :- To Create the Attachment Features (Ribs & Screw Boss) on A Door Handle through the given Class-A surface by creating tooling direction, the tooling axis for the given Class-A Surface should meet the requirements of the draft angle. Ribs:  Ribs…

CORE & CAVITY DESIGN :-   Aim- Create the Core and cavity blocks for the switch bezel designed   Draft Analysis- Draft analysis is the most importent thing for a part design process. It says, how Core & Cavity part are going to be and what will be the position of parting line & parting surface.…

COIN HOLDER DESIGN :-Aim-Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Take the thickness of the component…

 SWITCH BEZEL DESIGN :- Aim- Create the Switch Bezel Plastic component through the given Class-A surface. Start with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Thickness of the component…

BUMPER DESIGN :- Aim- Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.    Class A Surface- Class A Surface…

Aim: To create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model There are following things are as follows: Tooling…